8-Cylinder Magnetic Engine: Overcoming Lock Area with Unique Design

[@prometheus1111111]

it's a very beautiful design and very elegant. It really doesn't work in this configuration because the attraction side is just going to lock it immediately. You need repulsion on both sides and the timing of the repulsion Has to be calibrated so that there's a constant dynamic exchange on both ends. I suspect that the engineer knows this since anyone who went as far as to design the first case Would very likely understand the second case I just described. In any case these are very creative well designed red herrings that help a consciously intelligent person to actually think. thank you.

[@heinzpg]

" _It really doesn't work in this configuration_ " It doesn't work in any other configuration either. Never mind how elegant a design might be, conservation of energy can't be tricked. Permanent magnets can only deliver potential energy, no continuous energy.

[@alimohammadi7318]

Hello, engineer, according to my personal experience with magnets, the power of the insole magnet must be twice that of the piston magnets, so that the force balance is not created. Because if there is a force balance, the horseshoe magnet will not be able to push the cylindrical magnet back. I hope my opinion is useful for you. Good luck🙏

[@heinzpg]

According to the unanimous experience and knowledge of engineers and scientists this motor can't work and all proposals for changes to make it work are superfluous. A motor can't be driven solely by permanent magnets, this is outright impossible, never mind what exquisite designs are tried. Magnets deliver forces but they don't deliver continuous energy.

[@กอหญ้ากอไผ่]

It doesn't work because equal repulsion is generated in opposite directions at the same time.

[@Sammyboy1335]

You don't make sense the motion is being produced magnets have propulsion

[@กอหญ้ากอไผ่]

@@Sammyboy1335 Someone who fully understands the nature of magnets will easily understand that it won't work. This modeling program is not good enough for magnets

[@gumbogalloschke254]

It will lock, doesn't move a bit

[@jedujedi1981]

Show! O princípio inverso dos compressores automotivos ou lavadoras de alta pressão. Ideia bem interessante, porém o atrito das paredes e do disco, tem que resultar numa força menor que o campo magnético mesmo quando na menor interação, só assim produziria a sequência do próximo movimento. É complicado "vencer" isso. Mas, vamos em frente. É de idéias e tentativas que surgem novas técnicas e tecnologias. Parabéns!!!! Abraço do Brasil!

[@Archin-dn4bp]

on my channel really working gravity engine

[@alimohammadi7318]

Hello engineer, don't be tired. This concept design is interesting and useful! But make sure that the distance between the magnets is greater so that they do not have a negative effect on each other. That is, increase the diameter of the engine and reduce the size of the pistons. Be successful and victorious.

[@mithleshsingh4376]

energy can be neither created nor be destroyed energy is tranfer one body to another body

[@QuinceDeMayo-jg5wb]

Genial excelente trabajo! Ya estoy esperando su prototipo! Lo polos son los correctos?

[@En_theo]

Btw I heard that Algoryx (ANSYS) makes softwares that can simulate such machines as close as possible to reality.

[@patty1991]

😮 a whip for the v-gate inside and two flywheels with half magnets Genius!

[@travisrhead9911]

I can tell you how to make a working magnetic motor. And it's not on KZbin. And works. But your right about it being mechanical.

[@muratyorukoglu3490]

Bu motoru motosiklet veya bisiklete uygularsak verim alabilirmiyiz ..

[@marcelojaviertwt]

PERO AL FINAL TENES ALGUN MOTOR QUE FUNCIONE O ES TODO "TEORICO"???

[@witoldolbrych3140]

Where would the power to drive this device come from? Magnets after one, maybe a few revolutions will come into balance, what after that?

[@Hindkopakistan1]

A permanent magnet engine can be built. I have designed many diagrams it is possible but. Permanent magnets become loose. The magnetic field vanishes.

[@andreasschmitt2307]

No, that's all wrong.

[@pierrevandeputte2543]

When a system become more complex, some frictions apprend, and reduce the final "benefit". When it's too simple, you cannot expect solve all the problems. It's why a lot of reseaches don't acheve ..

[@carlosaguirre6341]

The problem I see with this is the amount of power loss on the flywheel pushing the magnets back and forth.

[@En_theo]

I was thinking the same, a lot of friction there. But it could be overcome if, instead another disk of magnets on the other side, we put a perpendicular disk. Once the first disk is in repulsive position, it will make the perpendicular disk spin which will repulse a 3rd disk. If the second disk can spin in such a way that this works, then it would demonstrate his idea is correct.

[@carlosaguirre6341]

@@En_theo Interesting!!! He should try your idea, I was thinking of getting rid of the friction or at least some of it by adding rollers on both sides of the end of the magnets, instead of pins touching the two sides of the flywheel but I like your idea better.

[@En_theo]

@@carlosaguirre6341 Thanks. Or we could imagine friction-less contacts with smalls magnets. I saw magnetic gears in other videos and it works very well if the motion is not too fast.

[@carlosaguirre6341]

@@En_theo You have good ideas. You should try to make a prototype.

[@En_theo]

@@carlosaguirre6341 I wish I had the free time for that, I gather pieces and make plans bit by bit. I should try 3D printing but i'm really too busy for that and these machines are not guaranteed to work once made.

[@knageswarrao6715]

I love and like your grafic design but realtime perfect prototype model need to best future for mankind. You know at present war for power. Thanks for your valuable time spending for better mankind life.

[@jamescooper9537]

I am wondering how I can contact you....*WOuldlike a free energy device on. my farm....ONLY to run a container refrigerator. HOW DO I? Thank you.

[@tempstep4058]

The gold looking plate will heat up. This is pretty much a heater.

[@BradKinard]

It's a ac compressor with magnets easy enough to try

[@RaidenMotion]

Intéressant super beau travail What's mecanic Cao are you using ? Love how you share ideas with everyone for the love of science and the best for the humanity Much appreciation 💛

[@JohnFreeman-ms3se]

Good concept, but needs redesigned a bit, their to much wear to be had on the top piece , and the disc is a part that will wear fast also. Remove top and disc and put cylinder heads and exhaust ports then fuel with hydrogen on demand , Use a direct air cooling tubes to cool the back of the magnets. Poof, John Rogers version of a hho magnetic engine

[@micheledestefano]

Le tue fantasiose simulazioni sono bellissime. Sei un asso con il C.A.D.

[@ouenergy2437]

It will not work!

[@travisbrimer772]

Where is the power source? The most difficult aspect for a perpetual energy machine is how you hide the power source.

[@QuinceDeMayo-jg5wb]

El comentario anterior de utilizar repulsión y atracción es para este prototipo.

[@randycoolbaugh1408]

Interesting concept. but im thinking this will "run" with any amount of efficacy

[@AhmetTasdemirDJLuds]

magnet motor is real. But this design can not work.

[@travelwithmssolangi959]

Respected sir Very good video

[@CapCarapy4]

Спасибо тебе товарищ!

[@ВячеславКолпаков-е5х]

Картинки механизма роторного или поршневого или какого любого принципа пусты пока не будет решена проблема изоляции магнитного паразитного поля

[@michalstano8857]

there is no such thing as a free energy, why can't people understand that

[@FajarYulianto]

Because they don't want to understand that

[@QuinceDeMayo-jg5wb]

La eólica la solar la hidroeléctrica y ahora viene la magnética?

[@victoryfirst2878]

I have a magnetic thermometer on my wood stove pipe. This heats the stove pipe to 800 degrees from time to time. The magnets never lost their attraction to the pipe. So how is that possible fella ??? I do not know what type of magnet is being used. Sorry.

[@mariobevia53]

Hello, your design is clever but it does not contain any gravitational or magnetic symmetry breaking. So the energy will not be able to increase with each half cycle and your prototype will not work for long and will eventually stop.

[@joshuabrand111]

Well I don't think this design could be used to drive anything but if you implemented induction coils into the cylinders you could technically use this as a compact generator. I'm using it to turn mechanical energy and rotational KZbin rapid lateral force and electricity..... Right here with a few alterations and to a compact Dynamo or alternator that produces a decent amount of electricity for a given mechanical force but it will still need constant mechanical force. The likelihood that it will be able to power itself for any extended period of time off of the magnetic fields alone is extremely low but with a few alterations it could make a great generator core for sale backyard windmill or a water wheel or replacing your alternator. Like it's not going to run forever or any long period of time under its own power because no thanks to Newton's second law.

[@joshuabrand111]

Long story short I do see several possible applications for this design with minimal alteration but not for the intended being a self-powering engine. However you could also take those same alterations and turn it into a electric motor with high torque low speed. For applications such as electrically powered power tools or other instances where you need a lot of torque but not a whole lot of rotational speed.

[@gnosisdg8497]

not going to work for a lot of reasons......anyway best of luck !!!you have to keep it simple in order not to lose energy due to friction.

[@ScrimmyBingus42]

Guy's unibrow is almost as good as mehdi's

[@philippehardel1242]

Bonjour c'est un système comme celui ci que je pensais réalisé

[@_M_H_T_]

That's better.

[@Hindkopakistan1]

Thets good idea

[@altaytandogan4949]

contrary to the laws of thermodynamics. free energy is not possible

[@QuinceDeMayo-jg5wb]

La solar la eólica la hidroeléctrica y ahora la magnética?

[@shinoo91]

did reall test bro

[@luiscosta4973]

Muy bueno 😃

[@Gacha.Cupcake]

خسته نباشید

[@jamesjohnson8754]

Will never work

[@monafatholahiUK]

👌👌

[@xvolodea]

👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎👎

[@reddragon7081]

لرزشش زیاده من انجام دادم شبیه ویبره میشه

[@QuinceDeMayo-jg5wb]

Tienes que equilibrar para disminuir las vibraciones en todo caso lo puedes acoplar a unos coginetes que te absorban las vibraciones?

[@teslabrasileiro]

🤔

[@aerys7273]

Fakers

[@irfanahmetoglu266]

HerzamanllarıELLAHTANCC.HürmetlerimleDuacıyızYardımcınızOLLSUN.ÇOKTEBRİKLERdiliyoruzAyretenDahaGeliştirilmişBaşarıllarıileHayürllıÇallışmallarıHOŞÇAKALLINIZ