#94 Parts received and a few Tips on the Collins KWM 2

Рет қаралды 17,341

7 жыл бұрын

We finally receive some much needed parts for future video repairs. Then we take a look at the KWM-2 and find why no filament on final tube.
Discuss on site
gokarters.com/smf/index.php?to...
Contact Info
gokarters.com/smf/index.php?to...

Пікірлер: 68

@kd4afw912 2 ай бұрын

First comment. I really enjoy your videos. Ive been watching for 2 or 3 years now. I felt bad for not giving you a pat on the back before now. Paul Carlson,Alan, TRX, MikesRadioRepair,, are also on my watchlist. All you guys are great teachers. Thank you Buddy!!

@TheRadioShop 2 ай бұрын

Thanks for watching

@jaybats7865 4 жыл бұрын

I get such a kick out watching you go through these rigs and bring them back. Thanks buddy

@stormchsr101 Жыл бұрын

an old fella brought me one of those old nationals to revamp. i changed all the power supply caps with new ones and i was letting it warm up. rig worked ok but when i stepped away from it, pow! if i would have been looking close at it, my face would have gotten a full force electrolytic unwind. as it was, it caught my hair on fire and burned my rug. sounded like a 22 pistol going off. let them warm up but point the caps away from you and wear some kind of protection when messing with power supplies!!

@PapasDino 7 жыл бұрын

I had a 3-500Z socket pin in my Drake L-4B go loose on me once; luckily they are super easy to replace and I had a couple of spare sockets to use as "parts mules". Thought I was going to have to replace the socket but luckily the spring clamp took about 30 seconds to pop out and replace and that bulb lit right back up. The loose clamp created a high resistance/high heat situation and the solder in the tube pin actually started to migrate down out from the pin. A little careful heating and addition of a little silver solder fixed that right up...lucky me!!! TNX for sharing Buddy. 73 - Dino KL0S

@TheRadioShop 7 жыл бұрын

Those 3-500Z sockets are my favorite to repair. Glad you got them going. Now try a capacitance socket for a 350B. What a night mare lol. Thanks for sharing that story my friend.

@TRXLab 7 жыл бұрын

Great job Buddy! Like the old Collins.

@ElPasoTubeAmps 5 жыл бұрын

Nice work. I have the KWM-2A, 51S-1 and a number of other S-Line pieces and love and use all of them. Out of 35 years using the 32S-1 and 75S-3, I have had only two issues with the transmitter, none with the receiver. A few years ago a capacitor went bad (shorted) on the screen of one of the 6U8's. I don't remember which one and recently the 2.1 KHz mechanical filter opened up on one side in the transmitter. It should read about 50 ohms DC resistance, both sides of the mechanical filter. Fortunately, I found a true NOS on Ebay. Thanks for posting and keeping this magnificent equipment running. 73 WA4QGA

@1903A3shooter 5 жыл бұрын

lOOKED YOU UP on QTH, nice looking trans you have. Love the Collins gear but do not own any. Take care Dave W4GSM

@dennisqwertyuiop 7 жыл бұрын

Great work, I think you cant find any better than Collins

@TheRadioShop 7 жыл бұрын

Thanks Dennis, yes it is about as good as it gets :)

@joepolen7212 7 жыл бұрын

Hi! Your voice is sounding better and better, you are getting over your pneumonia! Thanks for looking at the Collins, I like these S line ones quite a lot. I have a few of these, I like working on them a lot! I also have a National HRO 500 that I have recapped and repaired quite extensively, It is quite a radio and I like it quite a lot. I really enjoy hearing your commentary, techniques and approach to repairing radios on your channel so if you ever get a HRO 500 in your shop I would be very happy to hear and see your approach to aligning it and any repairs you make. I have just followed the manufactures procedure but I found online a ham that carefully describes an alignment method that uses his spectrum analyzer. I also liked your repair of your HP frequency generator with the broken plastic gears you did a while ago. My gears broke also but I bought a set of replacement gears off of you tube from a fellow in India. He used CNC machining techniques to copy three of the gears in brass. They work great!

@TheRadioShop 7 жыл бұрын

Thanks Joe. I am feeling much better but still tire out easily. Work a little then rest a lot lol. That HRO 500 is a nice rig. There is a guy on the west coast that wants me to restore his. Just hate for him to ship it this far. You know how shipping folks are. Those 8640 videos were my first videos I done. Mine works great but has developed a few bugs in the AM and FM tone generators. Going to have to tear into it and repair. My gears were also broken but was able to glue them back together, Thanks for the comment.

@TerryMcKean 7 жыл бұрын

14:45.. Awesome close-up ability in your camera... good score on that one, and, seeing that tube-socket contact sure brought up some great memories. :-)

@TerryMcKean 7 жыл бұрын

The tube-sockets themselves look great... no burnt insulator-material that would leak or arc, that I can see from here ...

@theradiomechanic9625 7 жыл бұрын

HI Buddy, I keep a selection of good used tube sockets and "steal" a pin as needed to do that same repair. Removing all those connections to replace the entire socket can lead to broken resistor etc. Especially when they are packed in like they are in that radio. Nice job.

@TheRadioShop 7 жыл бұрын

Always a good idea to keep some around. I do have a box of assorted pins that I bought many years ago. Along with wafer switch terminals. Like you said, so easy to break components when removing sockets. Thanks for stopping in my friend.

@larrysherwood9 7 жыл бұрын

Excellent video Buddy. Hope your feeling better.

@TheRadioShop 7 жыл бұрын

Thanks Larry. Feel quite better yes.

@bundylovess 7 жыл бұрын

Nice repair buddy good tip on cleaning tube socket pin big thumbs up

@TheRadioShop 7 жыл бұрын

Thanks very much allan

@mikesradiorepair 7 жыл бұрын

LOL, real HAM radios suck on AM transmit. :-) Nice to see the LA module finally showed up. Noticed what looked like metal film resistors in the one parts bag you got. Probably fine for the Fender amp but watch them on transmitters. Accidently ordered the wrong resistors a few years ago and the working voltage rating was lower then what was in the radio. They lasted about 2 minutes and went open. No smoke, no snap crackle and pop, still looked new and just went open. Learned my lesson there, read the spec sheet first.

@TheRadioShop 7 жыл бұрын

Not only does it suck on transmit, it also is terrible on receive. Was so happy to se the LA come in. Now I can learn a few new tricks lol. Only two resistors in that bag for the Fender, None of them for radios. More projects lined up. I agree they are no good in RF equipment. Thanks for stopping in Mike.

@mikesradiorepair 7 жыл бұрын

The Radio Shop Their usually fine in RF equipment, just need to make sure you order the proper voltage rating. I to have some studying to do with logic analyzers. Got the module that goes with my scope. Haven't had time to even plug it in and play with it yet. :-(

@TheRadioShop 7 жыл бұрын

Don't know why but I mostly replace with CC in RF stuff. And your LA is a lot more complicated than mine is. Should be a very interesting bit of gear when you get it plugged in.

@vetterfellow 7 жыл бұрын

Splendid Buddy.....

@TheRadioShop 7 жыл бұрын

Thanks!

@MrBugsier5 7 жыл бұрын

nice job again!

@TheRadioShop 7 жыл бұрын

Thank You

@1903A3shooter 7 жыл бұрын

Wow, 75 years old and never thought about taking the pin out of a tube. Dont work on gear like I did in the old days but fun to watch you. That is a great looking Collins rig. Clean and sharp. Thanks for Video, Dave W4GSM

@TheRadioShop 7 жыл бұрын

Thanks again Dave. I like to keep these radios as close to original as possible. Always looking at ways to restore tired and worn parts without replacement. These are some nice rigs. glad I get to work on them.

@wa6gxq 7 жыл бұрын

Great video buddy! I have a couple of collins equipment and have had them over thirty years. wouldn't part with them for anything. take care, hope you feel better soon.

@TheRadioShop 7 жыл бұрын

Collins equipment is awesome. Beautiful gear. Very tired and no energy at the moment but getting better. Thanks Barry

@larryk4mu240 7 жыл бұрын

Hi Buddy good video. Nice old 2A. Hope you video the NCX-3, I have one to start refurbishing either next or after a 700CX. Glad you're on the mend. 73

@TheRadioShop 7 жыл бұрын

Thanks Larry. Yep I am recording the repair of the NCX-3. Wish there was a service manual for these but never seen one.

@cuban9splat 7 жыл бұрын

Yes, I agree, I would keep the original sockets in it. Wow, thanks for the good tip about cleaning those octal sockets. I had never thought of pushing the socket pins out and cleaning them. Can you do that with 6 pin and 9 pin miniature tube sockets too? Excellent video Buddy. Thank you

@TheRadioShop 7 жыл бұрын

Most pins can be removed from the quality built sockets. Some sockets have the pins molded in and can not be removed. Thanks for watching.

@johnbellas490 7 жыл бұрын

Buddy thanks for that socket repair tip with the pins !! I was just working on an old Tube type amp, Its a MASCO 27 that has the same problem with one or two pins on one of the 6L6 final tubes that is making intermittent contact right now, so I will tryyour tip on pin removal cleaning and repair ! The amp is a nice working amp otherwise but I had to do a total RECAP and RESISTOR replacement, ALL the resistors had drifted to TWICE the value or higher !! ---- John A Bellas KC2UVN and take it easy and feel better soon Buddy!!

@TheRadioShop 7 жыл бұрын

Thanks John. Hope the repair goes ok. Should not be a problem cleaning those socket pins. Sounds like you are on the way to getting it rebuilt the right way. Thanks for stopping in.

@MrMac5150 7 жыл бұрын

Nice work..

@TheRadioShop 7 жыл бұрын

Thanks MrMac

@captlarry-3525 3 жыл бұрын

Good. Too much damage would be done replacing the tube socket.

@hs0zcw 3 жыл бұрын

what are tips on lube the tuning of the input array of vertical moving parts enclosed in the fiber tubes? Mine are sticky.

@Backtothefutureradios Жыл бұрын

Great video Buddy! Nice to see these rigs continue to operate……what is the ratio of your vinegar and salt solution? Any concentration of vinegar? Thanks and 73…..Larry W4PJP

@TheRadioShop Жыл бұрын

Whatever the amount of vinegar, keep adding salt until it stops dissolving. When you see crystals of salt you hit the spot.

@jma8352 4 жыл бұрын

great video again! i have a heathkit hw101 im working on with a spare hw101 the finals look simular. do you recomend removing all the componets and soap and water brush treatment then hot air drying methoud?

@TheRadioShop 4 жыл бұрын

Remove only the components that could be damaged from water. Watch out for phenolic material that can soak up moisture.

@jma8352 4 жыл бұрын

@@TheRadioShop thank you and blessings to you and your family

@YouAllKnowBob 7 жыл бұрын

Nice shape for the age. Sockets are like new now. I'd keep it original.

@TheRadioShop 7 жыл бұрын

Hi Robert. Yes I would agree, keep as much original as possible. Nothing at all wrong with it now. Thanks for the comment

@mrradioman445 5 жыл бұрын

great tips

@DonDegidio 7 жыл бұрын

Hi Buddy, Learned something new, how to remove the pins of a tube socket. Excellent info for someone who would have just replaced the socket. :-) Hope Mark will be able to assist in designing a replacement display board for the HTX-100. 73 WB3BJU

@TheRadioShop 7 жыл бұрын

Somewhere in the shop here I have a box od tube socket pins that I ordered many years ago. So much easier to replace the pin than the socket. Most of the time cleaning covers it. Already been on the phone with Mark :) Thanks for stopping in Donald

@warplanner8852 7 жыл бұрын

Buddy, I cannot recall seeing the specifics of the vinegar and saline solution you us for cleaning. Would you be good enough to pass it along? 72 de k6whp

@TheRadioShop 7 жыл бұрын

Check out my video #40. There is where you will find it.