999cc Extreme Duty Go Kart Swing Arm ~ V Twin Kids Go Kart

[@Twisted07]

I'd love to see RB build a Honda K-series buggy! Your recent buggy chassis have been awesome, would be sweeeet to see one with a K in it!

[@walkerfablab]

Check out our KiDz Buggy Build!👊🏻😈

[@scottdoubleyou563]

I second this. Somewhere on KZbin, a guy fabbed a 4wd tube buggy using a B18 non vtec and an LS trans w/limited slip, mounted longitudinally. The axles acted as driveshafts. It was yellow, and the clip showed it climbing a wall. If I can find it, I'll edit this post, and paste the link for the video.

[@jeremiahdingemans4151]

I've got a k street buggy project I've been sitting on i need to finish...

[@paulweaver1599]

It's just like TV waiting for that special episode of the season, you know all the suspense building up to it. This is just like that, it's all good though great fun great entertainment. Thanks guys, you'll get us there, eventually, LOL.

[@jesseshelby4383]

That v twin is going to be a handful for that buggy. Cool build 💪

[@fredericklogue6566]

Can't wait to see this rock.

[@bryduhbikeguy]

She's"A Brick House"...Take it Lonnie...

[@davidowen888]

I'm Excited to see this Gravybones Build fire up 😋

[@ALMIGHTYGARAGE]

That was mighty white of you to send John n ike that flywheel to help them out that's awesome bro solid of you

[@seangaudette4849]

Coming along nicely

[@lloydbaker7099]

You don't need no sticking breaks you don't need no thinking staring just right it man ride it

[@davidstephens81]

Love to see it run

[@kwatt-engineer796]

No doubt the solution you chose is the best one. But , it did occur to me that you could have aligned your sprockets on top of one another drilled holes through both of them. Then put spacers between the sprockets, bolt them up tight and the teeth are aligned. they will stay that way since you aren't using the key way to hold them in alignment. Finally , you could unbolt one of the hubs then slide it on the axle with the key in place and finally re-drill the bolt holes for the hub. Simple! Not so much, but an interesting possibility any way. As always I enjoy your fab videos immensely,

[@willieshaw2522]

Or hobbed another keyway in one of the sprockets.

[@CJLeTeff]

Looking awesome Greg! 👍👍🎉🎉🎉🎉🎉🤘🏻🤘🏻

[@jaredmcquiniff5362]

Dude, friggin sweet! Nuff said

[@tihspidtherekciltilc5469]

I suffered some wobbleness last night when I watched the video that made me subscribe. Hangover aside I'm early for once.

[@moyeet7]

the links to the v tread tires doesnt work, can you tell me the exact size? im assuming 22x10x10?

[@morgunfreedom4346]

Looks good, may have to replace that spring with a turnbuckle 👍

[@droberts573]

You folks are doing great. Love the Videos. Informative and funny. What else can a person ask for. Lol. Love it.

[@samwestoby140]

Sick looks like a lot of fun

[@DougsMessyGarage]

Red, you need to get/make yourself a rotary welding table. A rotary table would make welding hubs to sprockets easier.

[@RedBeardsGarage]

Yeah I have been wanting to forever now. I have a chuck from my lathe I just need to get the rest of the parts lol.

[@coleswolemma]

Do some portals on the talon 👀

[@airsoftgodfather]

Coulda skipped all that other mess and just got a high quality 420 chain. High tensile 420 would take a ton of abuse. I still use #35 reaper chain on my 20hp Tillotson with a juggernaut pulley. No issues

[@RedBeardsGarage]

This is not even on the same level as a 20hp Tillotson. The torque would be the issue. We have used motocross 420 chain in the past with 40ft-lbs of toque and stretched it a ton.

[@NCMATT]

Ride time woo woo 🙌 ❤ 👏 😍

[@joneserupinsmoke9161]

RBG 👍👍

[@soonergaming4747]

I’d love to see you guys do an alsport trike

[@tacozila1127]

Can you do a video on how you hookeed up the throttle linkage on a big block

[@bikescarsandmore6156]

I'm loving this build, I'm getting ready to modify my manco dingo frame, was gonna put a duromax 440 but got a sweet offer n sold it, same day I bought a gx390 for dirt cheap n runs just needs a new carb, but I have a 32mm flatslide on the shelf, can I throw it on n run it reliably or do I run the risk of blowing it up?

[@kingspooner3588]

Hey RBG, could you give a little information about the Clutch used on this motor?

[@chuckb9867]

I hope that chain tensioner works I don't know if it has bearings inside or not good luck with it looks shaky to me

[@hunterdan2002]

That spring for the tensioner is going to need to be significantly stronger, since the chain is going to want to stretch and jump when under load.

[@kenlester2725]

Plz do a Polaris 350 go kart build. I'm starting my build and could really use your expertise. To me it seems like a perfect build. Auto trans with reverse, and hi and low.

[@GoManGo-id8iv]

Didn’t see a link for the driver to fit that 1.4” crank? Any info greatly appreciated

[@sandraworkman2946]

Where did you get the torque converter thank you

[@RedBeardsGarage]

I have to buy it from belt palace. I will link it below the video.

[@kwatt-engineer796]

When we used to build airplanes we called it 90% done 90% to go.

[@6speedguy845]

What is your favorite brand of small engine

[@igokarts4510]

I like running the devil's gear ratio in my karts. 60tx9t = 6.66:1

[@cedhome7945]

I would put a chain and sprocket guard under the rear of the beast

[@tmurray1972]

What happened to the go carts and mini bikes that just have a front and rear sprocket…lol? What we had back in the day.

[@frankjames4439]

Please what hubs / rims and tire size in front

[@andertopmobi9494]

Show

[@nfra1663]

What happened to the sema build?

[@RedBeardsGarage]

I will be back in a month to be finished.

[@pspic04]

It needs a air horn

[@jesseshelby4383]

That will donkey, that will do 🤣🤣🤣🤣

[@willyoung4512]

Okay.... riddle me this Batman.... WHY do the chain sprockets need to be clocked the same? Lol

[@reviewaccount469]

RBG, did you eventually get your internet situation resolved? Starlink or cellular? I was watching a video on another YT channel on how a guy bought a wifi router with cell sim built in to get coverage at his place in the country and it made me think about your setup. He put an antenna on his roof connected to his wifi router and gets 50mb down/8mb up through cell towers. If you are still just using your phones, take a look at the "The Kelley's Country Life" channel.

[@RedBeardsGarage]

We ended up paying spectrum a lot of money to run it out here. My job depends on it so I had to have something reliable.

[@acurarl9929]

Why you running a govnor on that engine???

[@RedBeardsGarage]

Stock rods and flywheel. It wouldn't handle more rpm for long.

[@jonallen7191]

Man I really want to build this but I don't have all the tools lol

[@yungcashregister7185]

Am I the only one that thinks that the carb is way too small for this size of the engine

[@RedBeardsGarage]

Its a little small but its what I had on the shelf. Still bigger than the stock carb so either way its going to make more power.

[@brianbugher5156]

Nice try.

[@sotopr7]

Can u make me a colman mini bike swing arm i pay

[@russellafowler7403]

Why are you a jurk to Loni ? You talk to me like you do him ....quit belittling your help. Your bore bads are cheap yet you said he was costing you money. Really ....I'm sure you're not hurting for cash.

[@RedBeardsGarage]

I think you need humor. We give each other a hard time in the shop.

[@russellafowler7403]

@@RedBeardsGarage i understand shop talk. Had a shop for 17 years. But there is a thing called respect for the good people who work WITH you. Take care.