After watching your video I have decided to use this motor with 4s 40amp esc and 1045 prop. Will only do 100% on take off, after thst 75% max. Will it handle it?
@asangag Жыл бұрын
you will burn the motor ! 1045 is too big and it will over load the motor even at 75% .
@feltav5719 Жыл бұрын
@@asangag I need at least 1800grams of thrust. What doyou recomend?
@asangag Жыл бұрын
@feltav5719 what is the auw of the plane and wing span?
@feltav5719 Жыл бұрын
@@asangag 2000grams 1.60
@feltav5719 Жыл бұрын
It was a glow trainer with40 engine
@sunilpatidar73433 жыл бұрын
I have a2212 10t 1400kv moter i wants to rewind it with same voltage and rpm i have 36 awg /wire gauge how much turn i need to make this moter with same capacity
@asangag3 жыл бұрын
check this one out kzbin.info/www/bejne/inWvnXmaoLqHrJI
@armysatrio4 жыл бұрын
Hi... Thanks for the test with 4s lipo. Was wondering, did you test it on a full flight? Because the specification on this motor is only 2-3 cell batteries, CMIIW. Is it safe enough without causing the motor to burn?
@asangag4 жыл бұрын
Hi , Yes I have tested it on my XUAV skysurfer and Volantex Ranger both using the same motor with 8x4 APC prop with 4S Lipo. Once airborne it only uses about 4A of current at less than 50% throttle and the motor just slightly gets warm. Because both pf those planes are setup for long range FVP, they are bit heavy with all electronics onboard, and they need fair bit of power to take off , so 4S lipo gives that extra power I need for the take off . I would not run it at full throttle for more than 5mins. here are some links kzbin.info/www/bejne/iHfCZIKDfp6qhrM kzbin.info/www/bejne/iIO4d4SElrGie7M
@armysatrio4 жыл бұрын
@@asangag thank you for the reply. Its a bit relieved, I don't need to buy another bigger motor for my mini skyhunter. And yes, you are correct, once it airborne, cruising will need fewer amps and it glides more. Thanks again.
@Landat783 жыл бұрын
@@asangag hi thanks for test data. I checked your videoa..as i see you have changed the stock motor on the ranger and use only 3s on the skyhunter. So do you have a video with 4s and stock motor of the ranger? Thanks
@asangag3 жыл бұрын
@@Landat78 I bought the ranger secondhand and it did not come with the stock motor , but I replaced the motor it came with (NTM prop drive) with A2212 1400KV and 4S Lipo with 8x4 APC prop
@Landat783 жыл бұрын
@@asangag thanks for quick reply..im just before maiden with a ranger G2 ..i want to use it with 4s li ion with stock 2212 motor and stock 7x5 prop..but i was not not sure if it can burn the motor. I have also 6x4 apc and 6x4.7 hq i will test soon. So you have used it with 8x4 prop..?
@kamilahmed94563 жыл бұрын
thank u so so so much
@asangag3 жыл бұрын
Please subscribe to support the channel
@memoflix10753 жыл бұрын
Hi i have a kv1400 motor, 40A esc and 8040 proppeller. Is a 3s 30c 2250mAh enough ?
@asangag3 жыл бұрын
yes that is enough. More info: kzbin.info/www/bejne/ipiViZuGaaekiKc
@serdarbatkan14142 жыл бұрын
Hello Asanga I use 4S with A2212 1400KV but after %75 throttle engine stops immediately. I am using 40A ESC and 8045 Prop. I have 6 A2212 but 5 of them is not working after %75 throttle with 8045 Prop, one of them is working proper. Have you got any idea to solve this?
@asangag2 жыл бұрын
does the motor get hot ? also if you use 3S does it still cuts out at 75% throttle ?
@bhavyanshukadu28754 жыл бұрын
it was helpful ...thanks for testing :)
@asangag4 жыл бұрын
Subscribe please :)
@factbazar42863 жыл бұрын
Can we use 4s on 2212 1000 kv motor with 1045 prop and 30 amp esc
@Papiwatdiy4 жыл бұрын
Good test.thank.
@asangag4 жыл бұрын
Thanks! Please subscribe to support the channel :)
@chovapubggaming51713 жыл бұрын
Nice brother Keep it up ❤️❤️❤️❤️
@vojtechbednar98484 жыл бұрын
What motor 2212 approximately 1400kv can you recommend? At this time I'm thinking of this one and racerstar 2212 1400kv. Which is better? Can you tell? It is going in my AR900 with 8x4 prop and it will run 3S, probably 3s1p (18650) 3000mah
@asangag4 жыл бұрын
I found they both to be very similar in performance and I think they all come from the same factory. But the racerstar is more expensive. So I would use the non-branded one and I haven't had any issues with them
@vojtechbednar98484 жыл бұрын
Okay. Thanks 😄
@asangag4 жыл бұрын
Please subscribe to support the channel.. 😊
@zayyandzikraka38333 жыл бұрын
@@asangag the non brand 2212 1400kv (yellow motor) can it handle 4S lipo battery..?
@asangag3 жыл бұрын
@@zayyandzikraka3833 yes it can as long as you dont exceed the max current & overheat the motor
@factbazar42863 жыл бұрын
what will be thrust of 1400kv on 3s cause i am getting 750gm with 1000kv
@rcbuildmaster61923 жыл бұрын
Can I use it on park jet with 4s and 6050 prop i need atleast 80% throttle all the time ?
@asangag3 жыл бұрын
did you watch this kzbin.info/www/bejne/ipiViZuGaaekiKc it has all the info you need
@asangag3 жыл бұрын
current draw is about 15A at 80% throttle and it should be ok but check the motor temperature after flying for about 10 mins
@no_1one675 Жыл бұрын
What is the length and width of the motor
@asangag Жыл бұрын
not sure, just google it and you can find out as its a very common motor
@SubrataDas-nb6fl Жыл бұрын
Sir plz tell me, if I use 2212 1400kv motor which 3 blade propler is best to get maximum thrust, plz reply
@asangag Жыл бұрын
no, 3 blade prop creates more drag and the system will not run efficiently. The primary reason for three bladed props on full scale aircraft is ground clearance. or noise reduction.
@SubrataDas-nb6fl Жыл бұрын
@@asangag then sir, which blade is suitable for 1400kv motor to get the maximum thrust and motor and esc was not burn for heat
@asangag Жыл бұрын
@@SubrataDas-nb6fl you can use 8x4 or 9x4 APC style props to get good thrust without overheating the motor . 8x4 is what i recommend
@SubrataDas-nb6fl Жыл бұрын
@@asangag thankyou 👍👍👍
@factbazar42863 жыл бұрын
Can we use 4s on 2212 1000 kv motor with 1045 prop and 30 amp esc
@asangag3 жыл бұрын
I haven't tested 1000kv with 4S but I 'm sure you can use 4S but it will probably draw about 25A and thats over the limit of the motor as these motors are rated for max 20A. If you are not running it at full throttle all the time you could get away with 4S/1045 combo but I would use a bigger ESC ,like 40A
@msamodelismo953 жыл бұрын
Yesss
@danielemarchisotti49373 жыл бұрын
What about 8x6 with 4s lipo?
@asangag3 жыл бұрын
it will be closer to 8x4 E but about 20% less thrust but more air speed
@advancetech74792 жыл бұрын
10 inch prop and 2212 1400kv 3s lipo 2200 mah .. kitna thrust milaga??
@asangag2 жыл бұрын
10 inch is too big for that motor, you will burn the motor , so you get zero thrust & tears ! 😀
@advancetech74792 жыл бұрын
@@asangag for 10 inch prop which motor u will suggest???
@asangag2 жыл бұрын
@@advancetech7479 A2212 1000kv motor
@advancetech74792 жыл бұрын
@@asangag can i use d2826 1400kv
@asangag2 жыл бұрын
@@advancetech7479 that motor is only rated for about 23A, I would not use anything above 9 inch. even 9 inch can overload the motor if u run it at full throttle all the time
@KaranShamaliya4 жыл бұрын
Agar Motor 11-12 A se jyada le nai sakti continuesly to 12A zyada ka thrust test karne ka kya meaning?!!!! Straight forward 12 A pe 1400kv motor with 7035 propeller,756gm thrust generation
@animishaalagappa23273 жыл бұрын
Bro... 1400kv A2212 motor ka max rating 20Amps hai....
@aju54052 жыл бұрын
Hi.. I need one help
@asangag2 жыл бұрын
What ?
@aju54052 жыл бұрын
@@asangag I made fish rc plane. Using coroplast.
@aju54052 жыл бұрын
@@asangag used A2212 1000kv motor and 1045 propeller. Plane goes vertical if I give more throttle. I wrongly purchased 1038 propeller.when I used 1038 propeller on my plane the performance was great. It got nice gliding effect and more speed. What could be the reason?please tell. Iam confused