A3 Pro 5500mW 300 x 380mm DIY Laser Engraver Build,Test and Review!

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@Enthcreations]

I've got the 2500 one. I bought it one year ago. It works like a charm. One of my best purchases ever. Strongly recommended.

[@joyisamazingyeah08]

MIght it cut through cardboard?

[@maksxymilian713]

Hello, its still working?

[@pratikjambotkar4626]

Hi can it 2.5w cut white foam board

[@animes25]

I have the same laser as you, the problem that you are having with the lines is becauseYou need to tighten the motor bands, also it seems that the capacitors that the laser haves are not enough and then sometimes the laser lose power, to avoid that you can pause the laser after 1 or 2 minutes of work so the capacitors can refill again, you can use a keyboard/mouse control program to do that automatically. the other way is to use less power in your laser and move the motors slowly

[@NexiTech]

animes25 Thanks Mate! Tightening belts solved problem! Cheers!

[@punitsharma1204]

I want to buy it....i m not getting the link...can anyone share the direct link

[@nxvasix8696]

I bought a laser cutter, only a small a4 one to start with, and I spent a whole day fiddling around trying to flash Grbl and get the steps/mm correct. I nearly bashed it against a wall but I held back and succeeded

[@rakeshjadhav9238]

From where you got A4 ?

[@nxvasix8696]

RAKESH JADHAV got my 2.5W A4 laser cutter off eBay for around £90

[@1Peace]

A lot of people make their own custom dice. Can you engrave on acrylic dice?

[@williamgorman2403]

good assy video.time lapse and gopro view is great and good volume on music....only 6 min in and I subbed.... hope to see alot more from your channel. I also noted you reply quick to comments.... LIKE!

[@superman9693]

I‘d personally use a 500 mW 405nm laser because it‘s a single mode diode and produces much better engraving results

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@sunnydas2624]

Please price

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@MakersatWork]

But where to find the software for Mac OS ....thanks

[@steepjoe]

Can you laser mark metal using this machine? Metal marking with cermark or any dry moly marking sprays?

[@NexiTech]

Joseph Liu This laser engraver can not engrave or cut metal. You need way more power for that type of work.

[@JLAVES]

good video. Thanks. What is the name of the program and where can I download it? I have the same but bigger

[@gelaigalman]

Can it engrave 3d objects such as wooden brush, cup, etc?

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@argehandmadeknives1550]

Hello.. Can you possibly tell me what software you are using for engraver please..

[@mauricejohns3635]

Have a question about this engraver you have in this video. Will this do metal?

[@NexiTech]

No metal my friend. You need way more powerful laser for metal engraving.

[@mauricejohns3635]

Okay. I thought I remember seeing or reading or even watching somewhere on KZbin that these 7000 milliwatt ones with do metal Engraving

[@rickluchtenburg8166]

Will it engrave metal and plastics

[@NexiTech]

Plastic yes, but metal no.

[@getoutside8202]

Now that you have had it awhile does it still work properly? Would you recommend this?

[@NexiTech]

Yes it's still works like charm.

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@joshhanson79]

what software do you use? I have seen the benbox and the eleskcam software and have even heard of some better software you can purchase. I am just wondering what is the best software out there to get the best results.

[@brianbragg9857]

Hi I purchased a (Chinese) 2000MW but after working just once it will not open now with the software, what is the best machine and software for engraving and cutting acrylic up to 5mm thick

[@vernroach3413]

Great video...I have been thinking about getting one of these...Now, I know I will...My thanks to the gent that made it.

[@mayolormairez2527]

Have you tried it on plexiglass

[@NexiTech]

It will cut it but not transparent one.

[@pranitasingh6416]

Can you use it for leather??

[@NexiTech]

Pranita Singh Yes you can engrave in leather.

[@maroulla94]

I want to engrave on wood only. What it is best for me 2.5mw or 5.5m ?

[@NexiTech]

2.5W can engrave wood pretty good.

[@micmac9853]

i wonder if one can make silk screen stensil using this laser. Can it be programmed to punch microholes in a suitable material? it could eliminate having to use emulsion and burn masters?

[@1337-u5m]

hey does it engrave the glass? and able to cut it ?

[@NexiTech]

1337 I don't think so. I believe that you need much more power for that.

[@1337-u5m]

@@NexiTech Okay, I thought using it for cutting mirror and glass, thanks for your answer. :-)

[@artisangiftstudio]

Hello! Is it necessary to use a smoke extractor?

[@NexiTech]

It's good idea if you use laser for longer periods of time. For home use you need to open windows in the room.

[@artisangiftstudio]

@@NexiTech Thank you very much for answering my question,...

[@goodgoat6019]

Have you checked the accuracy of the cutting?

[@curtisbrown2667]

Yup, pretty accurate, just make sure the timing belts are nice and tight.

[@elsiebarnhardt3091]

does this machine engrave stainless steel ? I want to engrave stainless steel charms for customizeability but im worried if purchasing this would actually do what i need it to

[@NexiTech]

Elsie Barnhardt No it can't, you need alot more power for metal engravings.

[@TheALCHEMlST]

Hi Nexi Tech. I was wondering if you could tell me, if I buy a similar 500mw laser kit, and a separate 5500mw laser, would i be able to swap the laser out without any extra equipment. Both are 12v, can you think of anything else I might need or should it be as easy as a straight swap?

[@Jackmacnelson]

Can it engrave aluminum, down to a 2mm depth?

[@NexiTech]

I think this one can - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@Uplinkpr0]

Will this thing cut 3mm Acrylic?

[@billgabo]

that laser can cut fabric canvas?

[@fanalibroz2]

corta madera mdf de 3 mm ?

[@semindemedia]

Finaly! A good review!

[@ngoprekmania112]

Bang klo buat cutting poly foam bisa gak

[@IVMTAB]

Is this same machine compatible for both the European and American electric system?

[@nickpowers15]

Awesome video on installation and testing. This video has got me much closer to making a purchase, so thank you! A few questions. 1) What thickness of wood did you do the Eiffel Tower on? 2) Does it actually cut into the wood or just burning the top surface black? 3) How long did it take to do the Eiffel Tower? And what size is it? My art is similar style Thanks!

[@dougyorkno1]

Very Nice! Thank You!

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@just3dprintit377]

I like the music in this video!

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@daSamo123]

Hi. You are using the needed software with Bootcamp or a Virtual Machine? Do you think it is possible to use this software native on OS X? Regards

[@antoniovisconti3768]

If I want to add an additional fan to cool the area hit by the laser beam, what type of fan do I buy? And, for support, is there anything in Thingiverse?

[@NickSmith-hv9zi]

Is it possible to cut perhaps 3 to 5 mm balsa or 3 mm wood wiith this machine without modifications?

[@NexiTech]

Yes Mark! With 300mm/s speed you can cut through 3mm plywood in 3 pass. I you slow down even more you can cut through in 2 pass but it's going to burn maybe to much. It's cutting 3mm plywood pretty good. Possibly you can cut through even more thick plywood or similar material by just let the laser pass more times cutting line.

[@moraiscode]

5500mw does it cut MDF and Acrylic 4mm?

[@NexiTech]

instagram.com/p/BVk-UJNhLZI/

[@fychxhs]

Can you use it as a paper cutter?

[@NexiTech]

Yes you can

[@berman1972]

hai, it's possible to cut MDF wood and clear acrylic ? I usually cut MDF wood using CNC router, and need to know if I can replace it with LED laser

[@thegardenofeatin5965]

A diode laser isn't for you. A CO2 laser will reluctantly cut MDF--when cutting plywood, lasers have more trouble with the glue than the wood, and MDF is largely glue. Clear acrylic is transparent to blue light (you can see blue things through it, after all) so it doesn't absorb energy from a blue laser. Infrared lasers like CO2 lasers cut through clear acrylic beautifully.

[@rayalbertgonzalez6498]

I bought a 7000 or a 7 watt engraver, is it powerful enough to cut thin wood? I'm just a beginner at this. The only one's I see demonstrated are the 2.5's and the 5's. Also does anyone know what the best software to use is? I'm not too crazy about eleks software.

[@madbrit5053]

Hi, thanks for the video. will this laser drill 1mm holes in wood, have you triued, if not can you ?

[@joeblogs4146]

I was going to order one like this off Amazon from gear best only to get told it would take longer to arrive than they claim ?3 months) < > IS THIS TRUE "any advice" on this information I've been told by a third party Oh! and the import duty will amount to more the the whole system is actually worth is something else I've also been told. Thanks for the video it will certainly help many people out there.👍👍

[@Damian-wc2gy]

Can I use it to cut something?

[@NexiTech]

Yes you can. Thin wood sheets and fabric but not metal.

[@sumerudigitalprints6431]

can you please share the software link

[@theredmaster_superbee]

Friend ... I was trying to use the program to test my 550mw laser cutter and the laser light went on ... I hit a metal bar and the room lit ... I did not see it directly but I could feel the blue light ... do you think he hurt me? I did not have the glasses on ... it was only an instant and I know that it takes a millisecond to hurt ... I'm afraid that it hurt me.

[@masina100]

I think you could exchange the extruder with a laser, then you could laser engrave with your 3d printer

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@rkillian7233]

I'd like to see what its lilke engraving a wooden pen...could you do this?

[@marco.dallago]

Planning to make one with similar material, but larger, about 1mx1m. It is not difficult, and cheaper

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@obrendzuver179]

Please can you tell me, with this machine Can I engrave on metal, just engrave not cuting... ?

[@NexiTech]

Obren Dzuver No you can not engrave or cut metal. For metal engraving you need alot more power.

[@obrendzuver179]

Nexi Tech Do you think that 15W is enough for engraving on metal ?

[@blah123kkllll6]

can it cut paper?

[@NexiTech]

Yes.

[@kakxor3388]

can you cut 12mm foam ?

[@TARIQ821]

can you please tell me does this machine use for fabric cutting like polyester or cotton.

[@rick4x4]

Nice unit, I'm looking forward to getting one, the main use would be to cut 5mm white foamboard, have you done any test with this material? I would like to know if it would do a nice straight cut, without melting the foam away under the paper layer. Also, are you able to control the power of the laser, so you can either cut & engrave on the same process?

[@curtisbrown2667]

This laser has cut everything I've thrown at it with the exception of some metals. The power level can be adjusted and you can also increase the speed of the laser so its not in one place for too long. Just make sure you have extra materials because you will need some to practice on.

[@timdavies8938]

Will it engrave metal (aluminium)?

[@NexiTech]

Tim Davies No it can't. You need alot more power for metal engraving.

[@kilnprabu]

Hi its very good assembly,can we cut fabric like cotton or poly cotton

[@NexiTech]

Yes of course there is plenty of power. You can do it for hours laser diode has very good cooling fan on the top of heatsink.

[@Frika61]

Have you tried engraving steel?

[@NexiTech]

Nope I still need my eyes! :D You cant engrave steel or any metal with 5W laser.

[@rapidranjan]

Hey does it also cuts acrylic sheet, if so upto what thickness ?

[@NexiTech]

Only if is black. Transparent materials is very hard to cut with laser. With 300mm/s speed you can cut through 3mm plywood in 3 pass. I you slow down even more you can cut through in 2 pass but it's going to burn maybe to much. It's cutting 3mm plywood pretty good. Possibly you can cut through even more thick plywood or similar material by just let the laser pass more times cutting line.

[@davidcarter4419]

Can it engrave accrylic or Plexiglas

[@NexiTech]

Yes, but not transparent one.

[@ArtWars314]

can it cut regular WOVEN fabric? how about printing on it? with ink? can I put something under a transparency for it to cut the transparency? Can I upload my own pictures on a jpg, png or PDF? thxs

[@MichaelPetersenprideboy]

finally a english version i been looking

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@pareshsharma1]

I can use it for jeans engraving? Did u tried on it?

[@NexiTech]

Paresh Sharma It will burn them :) You have to go slow and adjust power output.

[@justinwesley2423]

Where can I buy the machine you are using? 🙏

[@antonw.415]

I might be a bit late, but you can buy it from ebay or amazon, just search for Elekslaser A3 Pro :-)

[@NexiTech]

Check the links in video description, it still sales on many sites.

[@dellvos2174]

Hello Nexi, can we customize the region of the laser up to 1000x1000 mm, and is it compatible with the software to cover up the 1000x1000 mm region? What type of picture format that the software can process ? Thank you

[@taskbarenhancer3386]

what kind of machine works on metal?

[@NexiTech]

Way more powerful industry type laser can cut and engrave metal.

[@ArashHamoon]

Hello, I would like to know which machine is more suitable for laser CUTTING natural leather sheets in order to make handmade bags, the 2500 mW or 5500 mW. Thank you

[@NexiTech]

Arash Hamoon I would go with 5500mw or even 10.000mw

[@anafale6889]

Sorry for the silly question, but I'm a bit confused since sometimes I see advertised 2500mW and some other times 2500MW, regarding the laser power. MW and mW are different powers... In the end, how much potency it requires and is it possible in a regular household?

[@technoshamanarchist]

A 2500 MW (Mega [or Million] Watts) laser would cut a hole through your floor, while consuming the power of your whole neighborhood. So they're all 2500mW (2500 Milli Watts = 2.5 Watts), and this is rather little, considering your microwave oven would use about 1000 Watts :)

[@LASERMASTERS]

What camera do you use to make the video? Thanks!

[@NexiTech]

Assembly video is done with AZ1VR Action Cam and rest of video is record with Samsung S7 edge with advanced camera settings. Lights is 4 neon standard lights 36W mount on ceiling. I could take everything in 4K but video editing takes ages. :D

[@glenwojcicki1792]

can u upgrade the laser at all

[@mohammedalansari2328]

i have question. can it engrave Mattel also and cut it?

[@NexiTech]

mohammed alansari You mean Metal? No you can't.

[@greiwepollio804]

What brand is this machine?

[@NexiTech]

kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@banesibinovic]

what is the thinnest line that laser can engrave? is that adjusted in software?

[@NexiTech]

You adjust the thinnest line by laser mechanical focus, then you control how many pass the line will be in the software.

[@ahmetyildirim3377]

Distance between laser and processing surface?

[@SajjadAli-ug8ns]

does it cut through tempered glass screen protector???

[@NexiTech]

Sajjad Ali Well I don't think so that is transparent material.

[@SajjadAli-ug8ns]

Nexi Tech can you give it a try and let me if it does i will be really thank full

[@giovannimilliner7666]

Can it do etching on metal like dog tags and a gun?????

[@eiurandelfkhan2299]

can it engrave on granite tile? without cutting or breaking the granite?

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@michaelaforeman3393]

I'm thinking of getting this to laser engrave my logo onto skateboard decks, do you think that would work?

[@dustinmoore6643]

As long as there is a way to get the deck under it probably

[@Kri5A]

how thick is the plexiglas from which the pieces are made?

[@martyjames6204]

Hi - excellent video thanks -question- would it accurately cut fairly intricate spray stencils? the material is acetate (plastic) sheet, less than 1mm thick? thanks

[@misterguy2929]

I wonder if this could cut eva foam up to 10mm?

[@jawadmehar856]

Can this engraving machine print on metal?

[@NexiTech]

JAWAD MEHAR No it can't.

[@bulentakyildiz5439]

Hi does this machine cut thin wood? Or isit only used for laser engraver? Thank you for sharing

[@NexiTech]

Guys check this new dual laser engraver! This thing engrave even stainless steel - kzbin.info/www/bejne/hqC2g5iXZrOloLs

[@gochengsadewa345]

I have something like this ... then I use it and make it. but why suddenly the laser can't be used ... what should I do?

[@pierredieu1620]

Est il possible de graver sur du bronze? Merci d'avance pour votre réponse . Google translation Is it possible to engrave on bronze? Thank you in advance for your answer

[@chunnikoli2091]

Very nice laser machine 😊. I have a small business and I want to know is this laser machine can cut and engraving leather and rexine please tell me

[@kbaskarahan]

Can be used to cut plexiglass

[@NexiTech]

Kml Bskrhn Yes but only dark colors. it doesn't work on transparent.

[@kaanuki3203]

Hi. Is your A3 5.5W adequate for cutting 1" foam? Would you recommend more or less power? Thanks.

[@elenaignatenko4236]

Hello, I bought a car with a le 5040 field. installed everything, but the native program on a large field, gives only a small picture. I want to make a big one. What program do I need to increase. thanks

[@bergoussi]

Do you think I can engrave on stones with this machine? Thank you

[@ldavidson11]

My next purchase.......great video

[@NexiTech]

TEMPUS MORIENDI Thank you :)

[@mariberbagi522]

Hi Nexi tech, is this machine can engrave curve surface? like a coconut surface, thanks

[@parkflyerindonesia]

Thanks for posting good review vid 👍😎 Will this cut depron sheet nicely?

[@smpkengineering677]

Hi. How Can i Buy this machine parts box?

[@wididewanaaditya3208]

I'm to lazy to google this thing.. could you expalin it the diffrence between 5500mW and 2500 mW in a simple explaination? thanks great Video, cant wait to see your next project

[@habanor9310]

Widi Dewana Aditya 5500>2500

[@e2theric858]

hello i am curious can this machine engrave a plastic magazine like for a m4 etc.? i only saw you do something that is thin in size. the magazine sits about an inch high when laying down would this be an issue?

[@bryanhauschild4376]

Did yours come with assembly instructions

[@cutflower36]

can i ask, is mw more powerful than the w? lookin at a 20w laser cutter, but i see some have the mw next to the number. which is more powerful

[@NexiTech]

20W equal 20.000mw.