ABB BREAKER FAIL TO CLOSE? why and how to fix it. benzblogs

[@arnelsace7076]

Weldone sir, thanks for sharing this troubleshooting video.

[@benzblogsVlogs]

Welcome sir

[@Jonflax07]

Ayos po lodi ganda ng content po God bless

[@benzblogsVlogs]

Sir salamat po bless u keep safe po tayo lagi

[@yusufmohamed5171]

Jazaka Allah Khayr Brother.

[@Abdurrahman-yc4we]

Let me know if there is any power from the motorized breaker close auxiliary and how much it will be AC ​​or DC ,breaker is close and also close and if there is no power, will the relay be operated? Please reply

[@benzblogsVlogs]

If you say close auxiliary it is only dry contact from your breaker you can supply ither ac or dc depends on your needs and also relay operated depend on the way you wired or design.

[@Abdurrahman-yc4we]

Please reply

[@ricmarjohnmatas7980]

Nice one sir..

[@benzblogsVlogs]

Sir malaking salamat sayo

[@ALBERTLUSTADO]

sir base on your experience does ABB CIRCUIT BREAKER IS ideal for generator where excessive vibration occur?

[@benzblogsVlogs]

Yes i never incounter that breaker having an issue due to vibrations its perfect for generator

[@arielbenjordan8719]

well done sir

[@benzblogsVlogs]

Thank you

[@jasonbule1207]

Sir, My Circuit breaker on a faulty diesel genset is showing "STP GCB Fail" and "wrn volt reg Lim" only when it runs with other generators. When it runs by itself, it doesn't show the two alarms. What do you think the issue is?

[@benzblogsVlogs]

Ok sir meaning your voltage low as the setpoint nominal now that why give trip now just adjust the voltage amd make sure it can be control by the module during sync

[@HermanToofa]

Good vidéo What about YO solenoid?

[@benzblogsVlogs]

Open close breaker

[@HermanToofa]

@@benzblogsVlogs if i have fail to open alarm?

[@HermanToofa]

Hi bro, what about deep sea controller? Could the problem come from this one?

[@ifrazpasha8965]

Sir my lift does not run if DG POWER is on

[@benzblogsVlogs]

Okay make sure the the wiring is correct phase and the boltage rating or your left is match to the generator and generator current aswill as your left

[@paulburton6215]

Should only open a breaker in test/trip position

[@benzblogsVlogs]

sometime you need to open to double check if aux contact still good condation sometime not working anymore or defective its make your sudden fail to open or fail to close

[@benzblogsVlogs]

Yes sir you should open the breaker in Trip or of position

[@ahmedfarouk184]

Nice 👍

[@JUNCOSTILLASVLOG47]

Nice

[@benzblogsVlogs]

Thanks

[@marpinohermoso5306]

Sir ano ho kaya kulang dito sa gina gawakong abb tmax 17h ayaw mag on 1250 po

[@benzblogsVlogs]

Can i see your diagram

[@ravikoundal9362]

Proses is long 2 dg set on load amx 500 kw then one gcb fail to close not possible for clear alarm and start dg again.

[@benzblogsVlogs]

Yes because it breaker position or the aux sw inside ither problem or posation of the breaker double check the wiring and output voltage from u1 u2 what breaker your using?

[@jinglingao-lingao5153]

Idol pag ganyan ba alarm fail to close nasa supply lang ba ang issue?

[@benzblogsVlogs]

Dependi lods maraming pweding causes Isa najan Ang supply,configuration,relay ,wiring connection Yan Ang mga pweding dahilan Ng alarms Kaya di gumana

[@jinglingao-lingao5153]

​@@benzblogsVlogsok naman ang relay ,wirings, dapat ba naka off position yong breaker bago mo salpak ang motor control mod.

[@benzblogsVlogs]

@@jinglingao-lingao5153 pwedi g naka off pwedi g naka trip ang titignan mo jan kong pomasok ng tama doon sa handle ng breaker para gomana ng maayus lods

[@jinglingao-lingao5153]

​@@benzblogsVlogssalamat idol... 👍

[@emmanbutler]

Sir, paano kapag 2170 GB Close Fail. Okay naman ang relay, minsan nag close siya, pero minsan ayaw talaga mag close ng breaker kaya lumalabas na ung alarm na GB Close Fail.

[@benzblogsVlogs]

Check ko yung aux contact di gomagana ng maayus kay ganyan nasa loob yun

[@emmanbutler]

@@benzblogsVlogs Paano naman kung sakali sir i-manual na lng yun, yung aux lng din ba aalisin or may alisin pa kami para imanualnon and off na lng breaker.

[@benzblogsVlogs]

@@emmanbutler kahit nakaw manual ka my feedback patin yun galing sa module pag di gumana matic iTrip Ng module Ang breaker

[@mikelorics983]

hello po idol. ano po kaya problema netong breaker. kapag inoopen namin nag koclose po ulit tapos mag o-open paulit ulit po closed-open

[@benzblogsVlogs]

PG ganyan close open lang Bago gawa ba or dating gibagamit na

[@benzblogsVlogs]

Check mo Doon sa aux contact Kong maayos Ang pagkaka salpok or my supply na pomasok balik Ng digital input para sa breaker feedback

[@mikelorics983]

dati na pong ginagamit idol, na repair na din

[@benzblogsVlogs]

@@mikelorics983 nasa limit sw lang yan or yung feedback sa module

[@sulmankhan797]

Nice vedio but music spoiled my brain

[@benzblogsVlogs]

Thank you sorry for that