ABS modul Corsa D 1,2 2007 0265950428 0265230285 FC

[@sekulicvelimir3171]

Svaka cast, jako ljepo i detaljno objasnjeno !

[@fur4ilo]

Браво братко!

[@ΧρηστοςΑγρινιο-γ9φ]

hello..... excellent video.... i have a combo 2008 with abs8.0, and cluster doesn't write the mileage(speedo works...) i replace the cluster but still have the same issue, i see in abs i have c0121, that i can't delete and some times i have and c0035(4) but i can clear it....... any idea what cause the main relay fault in this module???? thank you....

[@marinkorogina3743]

Imao problem sa abs-om na renault modusu. palila mi se tampica ispocetka povremeno dok jednom nije svijetlila stalno. uglavnom narucio preko i-baya polovno izašla me manje od 50 E ali kad sam je ugradio moro sam ić jednom majstoru da mi je upozna . Na mojoj staroj je nekako ušla voda kod elektronike i selenoida.sad mi je ža što sam je bacio jer bi se sad imo čime zabavljat. ljep vam pozz

[@ivanadimitrova6422]

Zdravo opel corsa d 1.2 pred nekj den mi svetna lamba za ABS SPE i lamba za rucna a ne radi mi strelka za kilometraza i ne pokazuva gorivo bio sam na dijagnostika ne gi cita dvata predni senzori na tockovite smeneti bos senzori i pak svetat isto dali treba kalibracija da napomenam kolata si koci se normalno kako i pred promenata na senzorite sta moze biti podrav

[@kamilszew6697]

Hello, do you know which pins of the connector respond to the right front sensor? I have an error with this sensor, the installation and sensor are ok...

[@RadovanPetkovic]

Try the pin 9-10 front right wheel 5-16 front left wheel 6-17 rear left wheel 8-19 rear right wheel This is for Corsa up to 2007 there are many types it is possible that this pin layout will not suit your car

[@kamilszew6697]

Thank you, my module is 0265950820 Opel Meriva B 2010 ...it is different

[@RadovanPetkovic]

@@kamilszew6697 Try the pin 6-18 front right wheel 22-34 front left wheel 20-33 rear left wheel 31-19 rear right wheel

[@dannygio4858]

Hello i have c0131 how to resolve?pressure sensor error

[@RadovanPetkovic]

The pressure sensor is very difficult to repair if it can be done at all. It takes a lot of patience, experience, a magnifying glass, a good soldering iron, excellent flux ... The video shows that sensor and how it is soldered. Well, maybe it will work... Attention: the gold threads several times thinner than a human hair break off this sensor when trying to remove the sensor's plastic cap.

[@AleksandarJovanovic14]

Cao druze, imam mali problem. Mehanicki deo mi nije radio na modulu. Tj jedan tocak nije kocio. Kupio sam modul sa istom oznakom (FC) i namontirao na autu. Sada mi se ne gase neke lampice, kako to resiti?

[@RadovanPetkovic]

Treba videti šta vidi diagnostika. Ako ima grešku pritiska. Senzor neispravan

[@AleksandarJovanovic14]

@@RadovanPetkovic meni sad tockovi koce, i auto radi bez problema. Ali na tabli stoji lampica za rucnu, za abs, i esp

[@ivanadimitrova6422]

​@@AleksandarJovanovic14 zdravo i kaj mene isri problem svetat i abs spe i lamba za rucnu kako si resio problem promenio senzor na tockovima predni i opet nista

[@AleksandarJovanovic14]

@@ivanadimitrova6422 stavio sam svoj kompijuter

[@AleksandarJovanovic14]

@@ivanadimitrova6422 rasturio sam abs modul, od svog, bez gresaka, sam stavio na onaj, i to je to

[@gm6067]

Pozdrav Raso. Imam problem na corsi d ne koci desni prednji tocak...tj abs centrala ne pusta ulje na izlazu. Da li je to problem u mehanickom delu ili ubelektronici? Lampice i greske ne svetle

[@RadovanPetkovic]

Mislim po opisu da je mehanički. Možda se može rešiti tj otpušiti raznim sprejevima i prtiskom. I nekim solenoidom oko tog ventila....

[@gm6067]

@@RadovanPetkovic Da li je potrebno kodiranje ako stavim drugu centralu sa istom oznakom FE ili da je rastavim i zadrzim svoju elektroniku a samo prebacim drugi deo sa mehanikom?

[@gm6067]

@@RadovanPetkovic tesko da moze da se to raspusi jer desni tocak ne koci ni malo,ne pusta ni kap ulja

[@RadovanPetkovic]

@@gm6067 mislim da nemora ali taj deo posla nisam radio pa ti nemogu 100% tvrditi. Mada i ta zamena elektronike može da prođe samo vodi računa na senzor pritiska ima tanke žičice da ne pokidaš

[@gm6067]

@@RadovanPetkovic jel mozemo da se cujemo sutra

[@salson80]

Pozdrav. Imam problem sa Abs pumpom na vw crafteru.Bil mogo dobiti vas kontakt broj da se cujemo da neobjasnjavam ovako Hvala unaprijed.

[@Крстан-о8ц]

Поздрав, имам модул за поправку па ако може контакт био бих захвалан.

[@lazarromcevic]

Da li moze kontakt tel

[@djakon6701]

Hello my friend. Very nice video. I have the same abs module. The problem is that the front left brake is always on (braked). Can you help me with this problem? Thank you.

[@RadovanPetkovic]

I’m not a car mechanic, I’m an electronics engineer, I don’t have that much experience. In conversation with fellow auto mechanics, I theoretically know what and how to do it, but I didn't do it. The problem is mechanical, the solenoid valve is stuck mechanically. The ABS body is removed from the electronics. Take care that the pressure sensor is not damaged !!!!!! Immerse in an ultrasonic bath (if you have one), then try to remove dirt from the valve with an air or liquid compressor, solenoid and 12v open one valve at intervals so that the valve works mechanically while trying to remove dirt from it. It is best to apply the opposite pressure from the direction that is in normal operation with the compressor. Why? Because that's the only way you can get something stuck out of the valve ..... How persistent and skillful you are can bring your ABS back to life. Let me know your results

[@RadovanPetkovic]

Another thing . Are you sure the d ABS module is a real problem? It happens that the plates get stuck, the rubber hose swells and the fluid cannot move through it, check everything from the wheel to the ABS and beyond. In any case, the car mechanic must check everything and say what the real fault is. Only then do repairs on broken parts. It happens that you get the correct part for repair and then we work unnecessarily

[@djakon6701]

@@RadovanPetkovic thank you very much for your answer. Yes I am sure about the abs module because I changed it with another module and works normally. From opel told me that the ECU board of abs module has the problem. But I believe that is mechanical problem like you because the abs light didn't turn on.

[@dannygio4858]

Hello i have c0131 how to resolve?pressure sensor error