ACC Advanced Programming: Decoders, Part 1

[@SailR108]

Remember, on multi-station decoders, you assign station number to first station and the program will automatically assign sequential station numbers to remaining stations on the decoder. For example..when u program a 2-station decoder, maybe you assign station number 4 to first station then the program will automatically assign station 5 to the other remaining devoder station. For a 6-station decoder if you assign the first station as #10 then the program will automatically assign the remaining stations as 11, 12, 13, 14 and 15 👍

[@janneels7873]

Thanks!

[@BlackViking72]

Thanks, was wondering about this

[@Rfc47901]

Thank you!!!!!

[@DrewC-ez1fj]

*THANK YOU!* That’s what I came here for! Good lookin’ out brotha!

[@fpplsoftwashpressurewashin8757]

I would recommend twisting your wires together prior to insertion into the wire nut. This is a much better connection.

[@Hunter_Landscape_Irrigation]

Thank you

[@brianlatkowski2037]

I am on a site that has the same controller. They currently have 99 decoders on the system. It is there request to install more decoders in a different section we are working on. My question is, will another module, be added or will another controller have to be installed? It will be another 60 decoders.

[@ItsThaKidTv]

I’m tryna figure out the same thing

[@ALAN-gn4ud]

Swap out to an ACC2 Controller. Don’t have to reprogram all the decoders just change the controller.

[@ALAN-gn4ud]

@@ItsThaKidTv acc2 controller. Just swap the controller out. Decoders all same and the programming is in the decider not the controller so it’s an easy swap

[@theoneandonlycole]

I have a question in regards to our 2 wire system. When we run station 1 (set at 45 min run time) on our 4 station decoder it runs for about 10 min and then the water (valves) shuts down but the time clock keeps counting down like the valves are still open. The other 3 stations run normally for the whole run time. What would cause this? Thanks!!

[@ario1mich]

Good controllers, easy to work with it.

[@joselozano9749]

Me gusta gracias por el video

[@lorenzobarrios4017]

Estoy tratando de programar un decoder exactamente a ese. Icd200 2 station decoder solo que no me da la opcion para programar la segunda estacion. Como programo la segunda salida? Oprimo los botones de flechas izquierda o derecha y no encuentro la opcion en ningun lado. Aqui en el video solo enseña como programar una estacion en un decoder doble. Puede hacer un video o darme alguna informacion?

[@smartyardhouston]

No se puede cambiar de el control. Se programan automaticamente en orden. Nomas con un ICD HP puede cambiarlos....

[@WaterDesignirrigation]

Now I need to hire a computer technician to help me in the field.

[@Josesal74]

Hello there, What about when the controller it’s showing a attention alarm msg What can I do to troubleshoot this problem I am not very familiar with this unit

[@Hunter_Landscape_Irrigation]

Hi Jose, our technical support team can assist you. Please email [e-mail]

[@TaxinGigs]

Thanks

[@Hunter_Landscape_Irrigation]

You're welcome

[@adictwow5923kgs]

Thank you very helpful

[@conanbrown7061]

what do you do after plugging decoder into the ports and decoder is not found?

[@rameldaiz2492]

What kind of decoder, acc2 and icd 100 decoder

[@southernreign1]

I do not understand why these wire connections are not twisted (and soldered) before the wire nut is installed.

[@smartyardhouston]

All these systems would be much less problematic if they would be soldered. Is there any device that soldering quickly in the field?

[@bobbymartin7640]

Not really because what if you’re Solinoid goes bad then you have to cut a re strip that connection again plus if used correctly dby connectors will not give you problems even the. Slime is voltage Rated to with stand shock and it won’t wash off your hand so you know water is not getting into it

[@GalaXy808]

what if not connecting to the computer station?

[@pedrobalderas7373]

tengo un contro Hunter Acc aunque este apagado se prenden barias estaciones algien me podria desir cual es el problema

[@brucelopez69]

Pedro Balderas tu control ya no funciona correctamente, nesecitas reemplazarlo

[@WaterDesignirrigation]

This isn't going to work for Hunter. Most techs , I am one for 27 years, none of my workers could handle this. Job is hard labor and not cut out for guys that can handle this stuff.