Accuair Endo CT Install and Comparison!

[@JohnnyPartV]

Was the wiring for the Endo tank long enough to reach to the battery. It seems short when I received mine.

[@christianarrieta001]

I’m think of doing this exact setup for my Q50 really appreciate the comments extremely helpful. Car looks great Btw 👍👌

[@WorkPlayDrive]

Nice setup and your car with those wheels... Amazing!

[@moocw11]

So what bags are u using. Airlift performance? Are you no longer using the 3p controller to air up and down?

[@MrTodd0218]

very cool. I have been following your thread about wiring the endo-vt with the 3P. Looks like you figured it out. What method did you end up taking to marry the two systems together?

[@stillplayswithcars7782]

thanks! it was honestly very simple. I believe i updated the thread with the answer. You dont actually marry the two systems together at all. You leave the 3p connected how its supposed to be installed, but you do not connect the compressor power and ground to anything. just cap them off. the Endo CT has its own wiring. A power harness (just power and ground to the battery) and a controll harness which you just need to connect to an ignition source. its that simple!

[@MrTodd0218]

thank you for taking the time to reply. Very cool and makes perfect sense! my last thing i was trying to compare is how fast the wabsco compressor is vs. two viair 480s. watching your video it looks very quick. Does the endo tank have a cap or something that would allow the connection of an additional air tank? Such as the ability to run two endo 3 gals instead of a single 5 gallon.

[@stillplayswithcars7782]

the fill time seems about the same on this endo CT (3.5 gallon equivalent) with the compressor inside ) to my 4 gallon with my air zenith. But honestly the fill time doesnt exactly matter to me much because its silent and you cant hear it. You can add additional tanks no problem. the tank has like 10 ports on it.

[@jbpasion071]

Julius Pasion 1 minute ago (edited) Will this work with Airlift 3H height sensors installed as well? What color wire is power and what color wire is ground from Airlift 3P? Where'd you get the power harness and control harness and subscribed to your channel!

[@stillplayswithcars7782]

yes it will! as said above, you dont hook up the tank to the airlift system at all. You leave the red and black wires not connected. The power and control harness come with your Endo CT or CVT. thanks for the sub!

[@rogelioreyes9331]

I need your help I have been trying connecting mine endo ct with 3H and I can’t get right what I need to do please

[@stillplayswithcars7782]

You don't connect the two systems together. Wire up the 3H on its own via the manual without connecting it to the compressor. Then wire up the ENDO on its own. Just power ground and ignition source.

[@richardvictorio7266]

Which connections from the Endo tank did you end up using to connect it to your airlift?

[@stillplayswithcars7782]

just power ground, and switched ignition!

[@Rx2NR]

Wow, that's easy enough. They gave me a CVT manual and the tank came with so much more wiring. Thanks for confirming!

[@Rx2NR]

Did you use the 2nd compressor signal wire on the Airlift wiring to connect to the Endo CT ignition wire?

[@AstonThaRat]

Do u have a switch box or are u able to adjust your airbag suspension outside of the car?

[@ZaipexJr]

Nice video man, cars coming along great!

[@stillplayswithcars7782]

thanks man!

[@tegbwoy91]

Nice upgrade bro!

[@ubcnme1]

HI on the Endo CT do you still run a Water trap with it. I seen some that had and some that don't. I know that they said that the compressor has a desiccant to remove moisture so clean dry air is always available...

[@stillplayswithcars7782]

you still want a water trap between your tank and your manifold.

[@ubcnme1]

@@stillplayswithcars7782 thanks for replying. I'll be purchasing one very soon.

[@victorrandall2038]

How much did it cost ?

[@allencurry4385]

Hey there. I'm about to do a 3p and endo ct install. Mind giving me some time and help? I've looked at the bag riders info but a little confused still.

[@Yourmadlmao]

Can i run this tank with a manual set up?

[@bernardstef]

Great set of wheels !!

[@ubcnme1]

Hey brotha on your endo CT tank does yours hold pressure over night for example if it was 200 psi is it same in the morning or it dropped alot to like 150 psi or lower. I rechecked all my fittings with soap and water and was leak free. So I checked the intake filter and sprayed the soap and water there and it started bubbling. That's where I found my leak. Accuair air sent me a brand new replacement tank and still had the same leak at the intake filter.

[@stillplayswithcars7782]

interesting, i have a small leak in mine, but i haven't looked into where the leak is coming form. I have multiple tanks so it will take some work to find it.

[@ubcnme1]

@@stillplayswithcars7782 check your intake vent with soap and water mines was leaking on both. I'm on my second tank now and waiting for a response from Accuair to send a 3rd tank. I'm not too sure if they are checking it before they ship it out.

[@stillplayswithcars7782]

@@ubcnme1 good to know thanks! will try to check my tank this weekend for leaks.

[@batman2036]

@@ubcnme1 does this tank need a drain like the old tanks or no ?

[@ubcnme1]

@@batman2036 The Endo CT comes with a drain fitting. It goes on either the left or right side of the tank...

[@leechavarie4675]

Looking good!Have you finished editing Driven 2018?

[@stillplayswithcars7782]

unfortunately i was so busy with the Still Plays With Cars booth that i didn't get enough footage from yyc. I will have a quick video from Edmonton though coming soon.

[@ubcnme1]

HI with the Endo CT setup does the "ShowMode" feature with on the Airlift 3p..

[@stillplayswithcars7782]

Show mode will work. but the Endo Ct will not turn on without the ignition being on. So essentially you can only use show ode until your tank runs low on pressure.

[@ubcnme1]

@@stillplayswithcars7782thanks again for answering my questions. I ordered the CVT but it's fortunately it's on backorder...

[@stillplayswithcars7782]

@@ubcnme1 Juft FYI, CVT does not work with airlift 3p.

[@ubcnme1]

@@stillplayswithcars7782 oh sorry i misread your question I got the CT not cvt..

[@stillplayswithcars7782]

Aiflitt 3p/3h already has valves.

[@rogelioreyes9331]

Please help