My new Husqvarna FE250 2020 deserves new handguards. Here is short clip how to install them step by step. If you have any question fill free to ask me. #acerbis #handguards #mx Music: www.bensound.com
Пікірлер: 33
@maybeerainmaybeesnow Жыл бұрын
Fully drilling the plastic throttle end and moving the throttle over slightly to the left are soooo key!
@JondavKTM3 жыл бұрын
That throttle grip is trapped against the hand guard, that will most definitely hang, I’ll be neatly trimming mine back slightly for good measure.
@BigElly123 жыл бұрын
Annnnddee I literally don’t have half the tools in this vid to install mine😭😭😭
@michaeln99203 жыл бұрын
How stable are these handguards and did they survive long? Nice Video!
@vrixty.9.83 жыл бұрын
They are pretty stable expesaly these ones these are the x factory so if ur bike falls over the handguards will pertect ur grips and ur clutch/brake, cuz it has that bar thing going in the grip.
@trey82952 жыл бұрын
Not stable break easily
@SmokinZen Жыл бұрын
So is the bar supposed to be even with the levers?
@ericstrohl522 жыл бұрын
What size is that step down bit?
@Skatafossy10 ай бұрын
There are adapters for tapered handlebars to put in the clamps, why haven't you used them...???🤔
@waxmanvids50152 жыл бұрын
nice!
@speedpilot3 жыл бұрын
Hello, I was wondering what happend when the motorcycle falls on the side with the gas handle. Is it possible that the protection slides further into the bar and may block the gas?
@shaunbean55533 жыл бұрын
No
@shaunbean55533 жыл бұрын
I’ve got these same handg guards
@gothops1543 жыл бұрын
How wide do you drill with the step drill? Just enough to fit the expanding end of that bolt? Or further?
@Modelar4ever3 жыл бұрын
2 mm bigger than size of bolt.
@julienhaag55353 жыл бұрын
can I instal them on a 22mm handlebar
@Modelar4ever3 жыл бұрын
Yes I think so.
@TheRoadhammer3793 жыл бұрын
Yes, 22mm is 7/8, standard handlebar size all over the world.
@andrewtorgerson61432 жыл бұрын
Damn this does not work with my pro taper throttle tube
@calderwood96412 жыл бұрын
My throttle doesn’t snap back when I tighten everything down. Any tips?
@Modelar4ever2 жыл бұрын
Unscrew the throttle a little and move it left so you will se end od the handle bar (1-2mm)
@jgruen98542 жыл бұрын
Trim the throttle tube
@ivantrejo66144 жыл бұрын
Hello, i'm looking a pair of this handguards for a naked motorcycle. Can You Say me the length of aluminium bar ? Please
@kcirtvpnotyvlc3 жыл бұрын
Best part of the video was the music! 😂
@Modelar4ever3 жыл бұрын
Sorry you did not like the video.
@patrickmeyer99052 жыл бұрын
@@Modelar4ever The videos good. The music could go though. It don't really matter just turn the volume down
@eastwood4006 Жыл бұрын
@@Modelar4ever I liked the video... Didn't think of the step bit. Going to try it without it first, then see. Seems like a good idea though. Thanks 👍
@shaw50473 жыл бұрын
So many fast-forward..
@dougsmith75803 жыл бұрын
Give me some fucking words. I bought these hand guards and I will NEVER buy anything from this company again. They DO NOT fit a Yamaha TW200. A waste of $90.
@apexwetdog2 жыл бұрын
I got them to fit my tw just fine today.
@dougsmith75802 жыл бұрын
Jason Barnes ….. Well done. I was at it for what seemed a lifetime and finally cobbled together a solution. I should have sent the bike to you for an install. Lol
@hfuklgrekf Жыл бұрын
Bought these for my xt350 and they won't fit right I ordered a different hardware kit hopefully it will work