Advanblack Dominator Stretched Rear Fender Fits 14 up

[@magusnagas8603]

Great video! Did it myself today. Watched the video as I went. Got it done it about 2 hours.

[@angelmalkemes2902]

Great video very helpful! But I did notice there was no mention on moving your antenna if you had one , other than that awsome video thank you !

[@grewal559]

I just installed my fender yesterday. You guys should make step by step video. I had to watch somebody's else video to install it. Not a big issue but still if you guys have step by step video with details. It can help many people to install it easily

[@Advanblack]

The video you just commented on is a step-by-step video.

[@danielgraham9104]

What happens when you already have filler lights from custom dynamics?​@@Advanblack

[@Gaming_Biker]

This is exactly what I was looking for. Bad ass. Now the only part missing would be an outer fairing for Street Glides 2014+. :)

[@RonaldDongen]

Hi Steve enjoy the video's greatly appreciated. My question is does the lisence plate fit the Netherlands size?

[@shonod]

Hey Steve, Dave here. I finished adding the Dominator fender and 4.5 stretched bags to my 2018 Road King SPC. I was thinking of adding the saddle bag guards rails that Harley makes. Would those work with the dominator fender? Rear bolt area I mean. Dual cut out of course. 13:42

[@rudegunner5661]

Gonna finally change mines out this weekend.

[@blackedoutbandit]

I need this fender and bags. I love the look.😮😮

[@jerryjones5732]

Will this fit on ‘23 road glide limited? I’m concerned about the wiring harness that the dominator fender comes with being that my turn signals are on my king tour pack

[@markduer3926]

Take off your docking hardware or risk scratching and marring the sides of the fender. Can also use a holesaw to route the harness underneath the fender.

[@rickmetzler3054]

Just received my Dominator fender for my '14 SG and this video is super helpful - I've watched it a few times, both before and after receiving my fender. I've got some different factors like we all will like CD lights around my back end on the stock fender, etc. as well as Legend Arc compression reservoirs mounted down low where the rear bracket attaches. So with that said, I have a couple of questions: 1) Did you pull the stock harness out, leave it or cut it? 2) Why can't the rear bracket and license plate be put on with the fender off and then clipped into the wiring after? ....again, thx so much for this excellent video !

[@jaymcneill103]

I just purchased this fender. Do you have a video showing how to install the lights into this fender

[@kuehl92]

Just curious, does the orange bike at the end of this video have the 4.5" extended bags on it from advanblack? I want the same set up at the orange bike for my 2022 streetglide. Also was size exhaust is that. 4.5" exhaust? I was thinking about getting the chrome 4.5" chrome works exhaust, hoping it will look identical to the orange bike, just black and chrome. Great videos btw, very helpful. Thanks

[@OZARKSHDRIDERS]

Always great stuff here on your channels Brother, thanks 💯

[@Advanblack]

I appreciate that...thanks man!

[@Advanblack]

I appreciate that...thanks man!

[@OZARKSHDRIDERS]

@@Advanblack anytime man 💯👍🏼

[@28cadi62]

Very helpful video

[@austinwilcox762]

FINALLY !!!! When this drops it’s in the cart for sure, can’t wait for that amber whisky!!!! When will these be available?

[@Advanblack]

very very soon...sign up for the newsletter over on advanblack.com and youll be the first to know. The dealers on FB are already taking orders from them as well.

[@alalvarez6026]

Great detailed installation thanks

[@Advanblack]

Glad it helped! Thanks for checking it out!

[@bighonkeyshera]

I know the cvo fender from advanblack is steel with an abs facia, this whole fender appears to be abs. How is the strength on it. Asking because the wife is always riding with me. Thanks

[@Advanblack]

My wife and I ride on this fender all the time..its plenty thick!

[@jonwarren9979]

I am interested in what y'all used for your audio and speaker system. p.s. and the turn downs. I purchased no cut out bags and fender!!

[@wam1388]

would this work with the regular stretched bags or would it look off? or would i need to get the cvo style instead. i really like the idea of the molded in license plate frame on this one, as opposed to the cvo's..

[@MRiverseltoro]

What pipes are those on the orange bagger at the end of the video during the walkthroughs? I like how they fill in the gap all around the opening. I need a set of those, my stock exhaust are too thin and leave a lot of space around.

[@Advanblack]

4.5 inch TAB Performance

[@CryptoiNNERG]

I need these! 🔥

[@GregMyers45]

Do you guys have the tank covers for a ‘22 street glide special. It has the gas port on the right side. Was curious if y’all over came that yet. Love your products!

[@Advanblack]

we are currently making it right now.

[@brandonhinsey4526]

When will you guys make this fender for a 2006 FLHTCUI? Thanks in advance!

[@oiscustomlife1741]

Hey quick question why don't you make a rear fender extension kit with cvo style vertical lights with either a lighted tri bar or dominator tip for guys like me who don't wanna give up their metal fender but want a little bit more of a custom look hell I'd buy one

[@Advanblack]

We have no future plans to make anything like that, unfortunately there isnt anything on the market like that from anyone that I know of.

[@oiscustomlife1741]

@@Advanblack ik that's why You guys should make one

[@michaelmccarty9333]

Which stretched bags go best with this fender? The 4.5” stretched bags or the stretched extended saddlebag bottoms? Or is there a difference between the two?

[@MPerry-cn8ls]

Really good looking fender. Would like to have the cvo style lights and the tri bar light together. What are the chances that will be offered sometime? Maybe just a fender extension with both types of lights on it.

[@Advanblack]

That is not something we are working at this time. I wanted vertical lights on the SG with the tri bar light and ended up getting plasma rods from Custom Dynamics ...radiantz also makes them...plug and play and you can have the best of both worlds...however it is not a the thick cvo lights...its a much more streamlined look.

[@jeffjones2493]

Hi Steve enjoy the video's greatly appreciated. My question is what brand battery drill are you using?

[@Advanblack]

Hey Jeff thanks man...number one tool used in our shop is that Milwaukie M12 ratchet. Hands down. That thing is a beast. All my M12 hand tools were purchased from Home Depot and some spare batteries from amazon.

[@jamesdunn3508]

Will this fit my 2019 electra glide standard. I'm looking yo do this fender with your stretched bags

[@GK-bh1tp]

Does this fender line up well with the tapered cvo style bags?

[@angelmalkemes2902]

Great video but there’s no mention of what to do with your antenna??

[@MRiverseltoro]

They sell a hidden antenna option that goes into the front fairings, check here: www.shoputahharley.com/products/boom-audio-hidden-am-fm-wb-antenna-76000863?variant=13634992963632&gclid=EAIaIQobChMI45jc7OOh8AIVrD6tBh0vnwKCEAQYAiABEgItEfD_BwE

[@rickmetzler3054]

Because I don't like the look of the long antenna and the short ones don't work, I have already turned my long antenna around and have it running along the left side, next to the batter and with the tip just a tad under the tank. There are several videos around on it. Now that I have the Dominator, this antenna set-up is working perfectly.

[@MontanaFree]

Will this work with my Custom Dynamics Magic Strobe brake lights? 2017 CVO Street Glide. Thanks! Awesome light!

[@Advanblack]

yes ...both of my bikes have the magic box and this fender.

[@Tonybfast]

What saddlebags from advanblac work with this fender? I'm bout change colors and will go with advanblack products. My bikes a 2016 streetglide special. Is everything plug and play? Good video

[@Advanblack]

This fender is made for the 4.5 inch stretched bags. Not sure what you mean by plug and play on ABS parts. The bags are drilled for your existing hardware and the fender is a replacement. Take your old one off and put the new one on.

[@EZridah83]

Can I install this on my 2018 Road King?

[@LexStar550]

What is the name/model/brand of the "custom turn down" exhaust system you are running on the grey bike? Can we hear it on your bike? Does it sounds as good as the TAB 50 cal?

[@Advanblack]

I built those turn downs so there is no link im sorry..they were a one off . Started with a simple cheap set of duals from ebay, cut them and welded on a 4" turn down tip also from ebay. Cut the rear hanging bracket off and installed an L bracket back there to fit the curve of the turn down. And no they didnt sound as good as tabs..to be honest they were obnoxiously loud...I didnt run them very long.

[@mike-pg5nl]

What about the antenna hookup? Since this fender does not allow for this, do you just remove the antenna housing underneath?

[@Advanblack]

No fender or extended fender has a hole cut out for the antenna. You can relocate your antenna with a hidden antenna that goes under your fairing.

[@joeshields8974]

Hey Steve,, great video!! Do they have any plans to produce this style of fender without the lights?

[@Advanblack]

Thanks Joe...not that I know of...not at this time.

[@neilcarlile63]

Are there plans to produce a chrome trim for the lights to match the license plate chrome surround?

[@Advanblack]

No..the lights do not allow for any trim to put on them,..they insert form the back.

[@twolrbuffalosoldier5514]

Steve, the bottom bracket, that ties into the filler lights, is it necessary to replace? Im working with a 19 Ultra

[@Advanblack]

It should be installed to re enforce the rear of the fender. Does your bike not have the bracket under there?

[@austinthacker7589]

Hey Steve, or anyone that can help with this question, I'm getting ready to do a build and want to change the color of my bike but want to stick with a harley color so I can order them "color matched" and save myself some painting. The question is what is the best way to see all of the colors you offer? Thanks in advance.

[@Advanblack]

Go to our website and click the "by color" option and you can see what colors we offer. www.advanblack.com

[@JNMIII-xh1xb]

Just ordered, do the Custom Dynamics Pro Beam CVO lights fit in ?

[@Advanblack]

yes..they are the same as the stock cvo lights as ours are...same fitment

[@wyomoto1349]

I was just about to ask the very same question.

[@shannonbires2961]

Steve does those cut outs line up with the stock stretched bags like on the cvo or newer SGS and RGS bags

[@Advanblack]

im not sure man I havent tested them yet. I just got this finished version a few days ago but ill let you know.

[@sickstring04]

Steve what’s up man, how is the contrast between the running lights and brake lights? Is there a big difference between the 2 or when you hit the brake is it only a little brighter? I know some other brands don’t have much difference in brightness between running lights and brake lights. Thanks for any info on this.

[@Advanblack]

They are significantly brighter when you hit the brakes or activate the turn signals.

[@fdxuser7242]

Anyone knows where to get those 8 inch speaker grill covers shown on this video ?...I thought they were AB, but they are not...

[@joem7260]

Was interested on what duel exhaust you have that you can use the no cutouts fender and bags ...thanks

[@Advanblack]

I had these custom made for my bike. There some turn down exhausts on the market and I purchased 2 different ones, which ended up being identical and neither fit with the bags so I had to go the custom route.

[@joem7260]

Thanks for the response... you have any videos or input on tuners for 2019 2020 glides...

[@ess_glide4427]

Hey Steve is that Carlet Grey?

[@Advanblack]

Charcoal Pearl ...oem color in 2014 sg

[@Sblack8123]

Will you be making this for the 09-13?

[@Advanblack]

this fits a 09 to 13 however the harness we have only plugs into a 14 and newer. We are currently working on harnesses for the 09 to 13

[@coolgeek08]

@@Advanblack how long we looking on that harness? I need that CVO before spring.

[@jmorrow8122]

Yeah also curious about the harness or is there a way you could do this with some splicing

[@biggmike419]

@@Advanblack any update on the 09-13 harness?

[@angelmalkemes2902]

Do you recommend putting locktite on the bolts when reinstalling?

[@Advanblack]

Blue loktite can be used in the install

[@erwindsouza785]

Those saddlebag speakers on your bikes, what brand are those?

[@Advanblack]

The street glide has all SP Audio out of Italy and the Road Glide has the Brazilian PRV speakers.

[@DustinG26]

it looks fantastic but i will 100% drag those

[@houstontaylor9799]

Will this fender line up well with Harley CVO stretched bags ?

[@Advanblack]

It will be a bit longer than the cvo bags but overall the area around the exhaust will match up

[@nobleff51775]

will the defender duel cut out match up ok with the cvo style streach bag?

[@Advanblack]

The cut out is the same so the bag matches the fender above the exhaust but the fender will be longer as its designed fore the 4.5 inch stretched bags and the cvo bags are about a 3 inch drop.

[@johnnycarvalho2538]

any chance you guys have something like this for an 06 ultra classic ?

[@Advanblack]

Unfortunately we do not.

[@douglasmembers28]

Hi Steve,, Doug here I have a 2012 road glide ultra is there anyway this fender would fit my HD?

[@Advanblack]

it will physically fit your bike however the molex connectors on the wiring are not the same.

[@douglasmembers28]

@@Advanblack Is there some sort of separate system I could purchase?

[@douglasmembers28]

@@Advanblack Is Advanblack coming out with 2009-2013 Dominator stretched rear fender.

[@douglasmembers28]

By the way because of you and your channel I have learned a lot and I saved a ton of money doing parts projects for my Harley. Thanks keep coming with these very informative vids.

[@michiganborn8303]

This might just be what I'm looking for to replace the old dog bone taillights on my 2017 Road King. ¤===[[■]]===¤

[@honeybunz_slayz]

Is it made out of metal or abs?

[@Advanblack]

Extra thick ABS

[@whskywolf]

Would those work on Road King?

[@Advanblack]

yes...14 and newer

[@Stomponya64]

Will these fit on a 2020 electra glide standard?

[@Advanblack]

Yes it will

[@tjflys]

The license plate frame is a horrible design when it comes to the wire harness. The wires come out in front of the plate which forces you to cut the license plate up top to give clearance enough for the wires to be routed. The wires for the plate frame really should have been routed differently. Bad design for such an expensive set up.

[@Advanblack]

Unfortunately, every curved plate frame like this one, from several companies are exactly the same way. With such a small frame it is hard to get everything packed into it and have a wire thats not visible after installation.

[@phdzzz]

Too bad, that the licence plates here in the Netherlands are so f#cking big😠

[@wesleypayne1870]

Do you guys make a rear fender for a 2007 street glide

[@obriantucker2256]

Will it fit 04 Road King?

[@Advanblack]

09 to 21