The hammer point won't break your windscreen. Windscreens are laminated, to allow them stay in one piece, even after an extreme impact. In an emergency, don't waste your time trying to smash the windscreen. Instead, smash the side window.
@fredjacques29793 ай бұрын
The hammer is designed to be struck in the corner of the windscreen same as a double glazing unit. Stress and weak point so it will work. If you try striking it in the center this is the toughest point of the screen and won't work!!!
@davidprice57076 ай бұрын
Thanks again for going through these tools
@delphjunction116810 ай бұрын
Hi Dan. Thanks buddy. Like the torch and hat. Head torch was part of our kit on the trucks. Always used it. Dust collector looks a great idea. Stay safe. Pete.
@johnsshed99510 ай бұрын
Cheap tools have got a bad rap that they don't last . But I have had an Aldi /Parkside soldering iron and a set of rarchet combo spanners that have stood up to a lot of abuse for at least 20 years if not more . when you need a tool its better to have a cheap one than not have the tool at all .
@richmondstar43547 ай бұрын
Bought a cordless soldering one and serving me well also.
@davidstaves666910 ай бұрын
Picked up the precision screwdrivers in Lidl a few weeks ago. They now come in a canvas roll up case. Couple of months ago found a very nice set of tweezers in a similar case. All excellent for model makers. Recently small items I purchased are: a set of micro drills, a box of heat shrink tubing, a box of crocodile clips and a box of assorted washers. In the past I purchased from Lidl a 5 speed bench drill, a linisher and sanding disk and a cordless drill. All have given good service over many years. I also gave a parkside portable generator which I use with power tools on a narrowboat - a snip at £99. Its worth keeping an eye on the website to see what's coming up.
@geoffdodd12910 ай бұрын
I found a set of precision screwdrivers in the reduced bin for £4 got home found them very nice but terrible as jewellers screwdrivers ( where you put a finger on the top and use a finger/thumb to to turn) , so pulled the back off a driver , used 1000 grit emery to remove the casting flash , a dab of white lithium grease , totally transformed in 30s per driver. This kinda sums up parkside , good tools with poor finish , I hunt the reduced bins , I bought some snipe nosed pliers for £2 , terrible rough grind and sharp edges , spent 4 minutes ( watching youtube) with 500/1000 grit emery , now they feel like £10 pliers., very happy with their welding rods and angle grinding discs.
@zoothornrollo996010 ай бұрын
The magnetic bars are brilliant. So useful for holding drill bits, small spanners, tape measures - anything with iron/steel.
@donaldpaterson582710 ай бұрын
I use my magnetic bar as a magnetic wand searching for small screws and so on dropped into the carpet/floor.
@zoothornrollo996010 ай бұрын
@@donaldpaterson5827 Great tip. They seem to be in stock regularly at my local Lidl so I'll buy another one now! Cheers.
@johnboyle40629 ай бұрын
Great for boat to hold baits out of the way
@roystudds194410 ай бұрын
Some amazing items at great value there. I particularly like the hat. I don’t often go out in the dark because my vision isn’t so good but when I have to go out on poorly lit routes that sounds brilliant (no pun intended). The last item is also a must have. Thanks for sharing. Roy.
@mickheathcote457010 ай бұрын
I've had the Aldi screw extractors for years, drill a hole first and they work brilliant.
@carolinerogers105710 ай бұрын
Always good tools in parkside make my husband dave got loads of different tools
@Alan-r2v9s10 ай бұрын
All the tools I have had from Aldi and Lidl have been amazing, no problem and a fantastic price.👍🏻😎👍🏻
@dg129410 ай бұрын
You need to show them in action, otherwise how can you say they are good value for money?
@andrewharrison598310 ай бұрын
Nice to see another review, it's been ages since your last one! This time I think I need to go to ALDI.
@quaich1410 ай бұрын
Thanks for sharing. I bet there are no car safety tools left!!!! As for the screw removal I bought a set a couple of years ago with little success.
@LeClerc4818 күн бұрын
Before you use the damage screw remover drill a pilot hole in the damaged screw, drill it the correct size to correspond with the screw remover, but ive also used a file, i take the handle off and drill a hole in the screw and then i hammer the square end that the handle was on into the hole works 9 out of ten when ive used this method
@stephendavies694910 ай бұрын
I must get a set of those screwdrivers. I keep putting it off due to having loads of screwdrivers, but perhaps it’s time to chuck a few of them in the bin and buy the ones you bought. It’ll be interesting to see how that UHU glue works. It was seen as a top brand back in the day.
@BedsitBob10 ай бұрын
Have you noticed how tool names are becoming Americanised? Hex Keys instead of Allen Keys, and Wrenches instead of Spanners.
@frankklein487210 ай бұрын
No, just you, I buy Japanese
@b.nichols32559 ай бұрын
It's what we call 'dumbing down'.
@G5810 ай бұрын
Forsner Bits are for counterboring or shallow flat bottomed holes. They are not really a substitute for twist drills.
@samwoodward849110 ай бұрын
Had same problem with screw remover. Great vidios
@BedsitBob10 ай бұрын
For escaping from cars, get yourself a Resqme. You can attach it to your keyring, meaning you have it with you even when not in your car, meaning it's there if you need to rescue someone else from their car.
@basher8758 ай бұрын
I would just use the headrest it’s removable and has a sharp enough point to smash the windows to let you escape You know where it is rather than searching for a tool in your glovebox
@BedsitBob8 ай бұрын
@@basher875 You don't keep the Resqme in the glovebox. You keep it on your keyring.
@JohnColgan.10 ай бұрын
I bought sanding pads earlier this year. The velcro came adrift from the sanding pad
@steveakam10 ай бұрын
I bought the hat with led light for walking the dog, damnd usefully at night for finding the stuff you.need to pickup
@nf54169 ай бұрын
with regards to the damaged screw remover , you first drill a hole in the screw head then you select the next size up from the drill bit you used , then jobs a good one ...
@jublywubly9 ай бұрын
I've bought a few tools from Aldi, over the years. So long as they're not electric, they usually work. (I found most electronic things from Aldi break in no time.) 2:30 Technically speaking, only the 6mm (1/4") hexagonal key wrench is an Allan key. 12:50 Also, only the 6mm (1/4") cross head screwdriver is a Phillips. ;-) 15:30 Someone told me the best screw removers have a flat lip around the widest part of the threaded end. That allows the bit to grip tight, like having a head on a bolt.
@GreenJimll9 ай бұрын
I've had an LED beanie hat for a couple of years and found it very useful. This year i picked up a second one from an Amazon seller that has two LED lights. The front one is white as shown here, and the rear one is red LEDs. The rear has two steady intensities and a flashing mode. Very handy for walking on dark country roads around me that have no street lights.
@anfieldroadlayoutintheloft520410 ай бұрын
good vid on the tool you got will goot to addto you tool box thanks lee
@BobMuir10010 ай бұрын
Hi Forstner bits are not for countersinking, a countersink bit fir £2 will do a far better job. Forstner bits are great and you will find many uses, holes for magnets being my favourite! An awful lot of car windows are coated so will not break with a hammer device. There is a newer tool on the market. I think the covering on the mag strips has got damp? Parksides fit n finish is better than that!! Bob England
@alanrichardson16728 ай бұрын
Fornster bits are used to drill flat bottomed holes usually for cabinet hinges.
@andrewellaway908610 ай бұрын
I use the Forster bits to drill cable routing holes in my base boards.
@jimboisgr85 ай бұрын
15:40 I would normal drill a small hole in the screw first which then let the screw remover get a better bite.
@AG-cg7lk8 ай бұрын
Check the brass brush with a magnet - a lot of cheap brass brushes are not actually brass but coated steel, which means they can damage soft metals.
@limpet99 ай бұрын
I`ve always wanted a rechargeable hat
@teljoy3861Ай бұрын
The parkside magnetic strip has a protective film on it which should be removed
@belperflyer74199 ай бұрын
Never buy cheap Allen keys, they just mess the sockets, especially the smaller sizes. I keep my Cyano (Superglue) stock in the fridge or it tends to get thicker with time (I'm a RC aeromodeller and I use a lot of it). Oh, and I hate magnetised tools - they attract small screws that are in place but not started - very annoying. If you need a screw to be attached to its driver to access a tight spot, use Blutak. I like the screwdriver set except for the magnetism. I have a Workzone scroll saw from Aldi and always have look at middle aisles when I go in. Interesting video.
@emmabird97459 ай бұрын
Hi. I've tried screw extractors like that several times and I've given up on them. They're useless. Like the idea of the hat, wish I'd seen it, I'll watch out for it next time. I reckon it would be good for winter walking down the woods in case you're still out for half hour after dark.
@Azureecosse10 ай бұрын
Tools from Lidl are usual good quality cannot fault them but Electrical good like drills and a like never last long in my experience I have had three drills from Lidl and a Nibler the rechargeable tools in particular you are lucky to get a years use out of them the rechargeable batterie's don't hold a charge well I have three 20v Parkside batteries replaced , granted Lidl swapped them (with the receipt) but the Nibler they refused to replace as I lost the receipt, pretty amazing given that it is their own brand Parkside and had burnt out when tested, two drills the clutches burnt our too quickly for my liking, I think hey are made of cardboard, I just wont buy electrical Parkside goods any more I wait until the screw fix winter sale an buy there , you pay what you get with Lidl and Aldi I have learned from experience. I am joiner to trade I will only buy Makita now.
@jimlepeu57710 ай бұрын
You need to try Ryobi One+. I have used them for about 18 years and have never had one fail. I even have a drill from before One+ and it is still happily dodging along on One+ batteries.
@johnrhodes335010 ай бұрын
I generally like most Lidl Parkside stuff that I've bought, but I'm quite selective and will only consider half of it depending if it looks ok quality. Did getting a regular rechargeable drill once and it never reach felt right. Then it started to get a bit clunky. Should have taken it back because I always keep the receipts. Then it sort of clunker slightly and cut out when the drill was on its side or pointed down. You guessed it.. Now I'd lost the bloody receipt and it must be nearly three years. So I took it apart, only to find one of the orbital gears was totally missing. It had never been fitted because where the gearbox had a reasonable dollop of copper grease, there was a totally clean patch where the bloody cog was missing. Was almost tempted to buy a new one and try to take the old one back for a refund.
@toothfairy78849410 ай бұрын
I have used them and they work
@paul1302556 ай бұрын
As already said the hammer point won’t break windshield because it is laminated but will work on side windows.
@kelvinsparks465110 ай бұрын
I bought a Parkside wood router a couple years ago, it blew up ( almost literally) after very little use , so that has left bad taste for future purchases.
@frankklein487210 ай бұрын
Parkside had one for £40, Makita sell a 240v one for £60......hmm
@youtubeman50339 ай бұрын
The hat looks brill
@Steve-dr7rr10 ай бұрын
The screw remover normally comes with both ends one to smooth the head the other end to remove or I got a set not used as yet but also got the screw extractor pliers
@BedsitBob10 ай бұрын
For removing broken bolts/studs, you're better off with some left-handed drill bits. Drill a pilot hole, a size smaller, using a standard right-handed drill bit, then use the left-handed bit at slow speed, to back out the bolt/stud. It works best in a drilling machine or milling machine.
@dellawrence432310 ай бұрын
Exactly what I was going to say, spot on.
@steveknight13149 ай бұрын
👎
@ianhill45859 ай бұрын
I agree with narrator,I've got that screw remover kit,and never had any success with it as yet.
@christopherbooth17729 ай бұрын
The uhu gell superglue is good when used but shocking to get out after 1 or 2 times of use
@ianhill45859 ай бұрын
I worked with diesel fitters who'd spend out for expensive tools, and they'd say yes they're expensive but long lasting---- that's great up until the point you leave it on the truck somewhere and never see it again. I'd rather buy 5 cheapo spanners for what they paid out for 1 of them. They snap or get lost, replacement cost is cheaper.
@jimboisgr85 ай бұрын
I know it’s been five months but the at 13:06 you described the precision screwdriver set, you called some of them Star bit, and you were not sure of its proper name, which are call “torques”
@brianrees9393 ай бұрын
Torx
@mikemoran741610 ай бұрын
Great for walking the dog
@b.nichols32559 ай бұрын
I bought a hex-key set from Lidl. Be careful when buying, until I came to use mine I had not realised that they were imperial sizes.
@peterc445010 ай бұрын
What size screws are you using to use a forstner bit to sink them.
@AJB2K310 ай бұрын
Did you not have end caps with the magnets? All mine I brought this month had end caps.
@ebxo26910 ай бұрын
With the led work hat, if you press once to turn on the light , then press and hold again 2/3 seconds it will flash,, brilliant when out walking or riding a push bike or scooter. They do not state this in the instructions. some may not, depending on where you buy them from, try before you buy to get the flashing one..
@MrTimmmers9 ай бұрын
That glue is amazing at gluing it's top on so you can't use it, and drying out so that side squeezing does nothing. If you buy it to use once, great, otherwise not.
@Chippyclip-zj3xo9 ай бұрын
A little tip for any super glue, once opened rub Vaseline on the nozzle it stops the glue from setting in the bottle and stops the lid from sticking.
@colinosborne38778 ай бұрын
Bought a box of twist drills 1-5mm. Two were sharpened backwards, another broke as soon as it touched mild steel and the others were badly sharpened, either wouldn't cut or off centred and never used. I would never buy anything like cutters or pliers as the steel is rubbish.
@elvisoshaughnessy41099 ай бұрын
Very true
@philquinn637510 ай бұрын
Good video to be fair
@mattikaki9 ай бұрын
I have tested numerous Lidl Parkside tools and most of them have been pure s*it. Forstner bits are badly made and 35mm one I tested, made too large hole for those hinges. In my web page I have many other examples which tell that Lidl buys the cheapest items they can get and it looks also that Lidl buys large lots which are too bad to sell otherwise. That screwdriver set looks interesting but probably it sells really fast if Lidl Finland start selling them.
@wahiba10 ай бұрын
Variable stuff. Mini drill and gun style soldering iron from Lidl did not last long. Screw extractor set was too soft! Other items though have been fine.
@gerardbonus53549 ай бұрын
My tip with the glue is to use it very, very soon.
@Chippyclip-zj3xo9 ай бұрын
A little tip for any super glue, once opened rub Vaseline on the nozzle it stops the glue from setting in the bottle and stops the lid from sticking.
@ianplatt305410 ай бұрын
I just have say that I think you are wrong about ALDI batteries, I have found that these batteries seem to go on for ever, the ones I have in my electric toothbrush lasts for somewhere around 8months or more, the duracell batteries that I had a few years ago were not much different to a lot of other brands.
@chattonlad938210 ай бұрын
Agreed, I reckon they are as good as Duracell, if not better.
@austinlloyd975710 ай бұрын
Yes but if you got bad teeth cos you saving batteries 😆 🤣 😂 😹
@teljoy3861Ай бұрын
On the magnetic strip
@stephenlines94319 ай бұрын
Does anyone know if the Parkside magnetic tool holders can be cut down (they never seem to be the size I want)?
@snowflakemelter117210 ай бұрын
That super glue was a total fail for me, nothing but a couple of drops ever came out of it.
@JohnColgan.10 ай бұрын
When you finish gluing for the day, tap base of bottle on table and ensure no glue remaining in tube. Then the glue won't set & block the nozzle. Store upright!
@BobMuir10010 ай бұрын
The side ‘lever’ system is brilliant and is the tube that has never let me down! Bob England
@Chippyclip-zj3xo9 ай бұрын
A little tip for any super glue, once opened rub Vaseline on the nozzle it stops the glue from setting in the bottle and stops the lid from sticking.
@mapp0v010 ай бұрын
The super glue is only 3g normally that dize bottle is 20g.
@leso.k.k877010 ай бұрын
7mm always missing from set's of a lower price range,be aware!
@peterc445010 ай бұрын
The damaged screw removers in my experience are a waste of metal and money.
@roberthoug78649 ай бұрын
699 for a set of drill bits, and 299 for a stupid thing you don't even need, to catch some dust when you can figure that out for yourself How to catch it. Some things are just not worth the price eagle
@GrahamBrown-jk3rc6 ай бұрын
Withe respect, you could make these videos so much much more useful: were the drill bit cutting edges properly formed: did the goggles conform to any GB orEU safety spec....... and so on. I appreciate that the items are inexpensive and are possibly well made in the EU but if sorced from other countries they could be total rubbish or dangerous..... as many a worker has found out.
@stievboyo6368 ай бұрын
Can get all these things from Poundland much cheaper
@martindaubert16369 ай бұрын
What's the point of showing the tools and glue if you don't show if the work
@leso.k.k877010 ай бұрын
Torx !
@peterjohnson493210 ай бұрын
Are they paying you for this ad?
@dansmodelrailways788610 ай бұрын
No mate, i just enjoy buying some bits and doing the videos. No sponsorship or anything like that.
@royevans45819 ай бұрын
I have found someone that is worse than me for buying tools lol.
@martinahardaker87399 ай бұрын
wouldn't park in their car park........
@ANDREWLewis-p9j9 ай бұрын
What ever price you show triple it for UK 😢
@dansmodelrailways78869 ай бұрын
They are UK prices.
@ANDREWLewis-p9j9 ай бұрын
@dansmodelrailways7886 realy I was getting a dollar sign, not a pound sign
@robertovers186310 ай бұрын
super glue ! great for bonding skin ! not much good on anything else
@ianhill45859 ай бұрын
Agreed, I prefer good 'ol Araldite ,I used the 2 tube twin mix kit.
@aleddavies77010 ай бұрын
What’s the difference between Aldi and Lidl? I’ve always been confused 😂
@nigelmchugh554110 ай бұрын
Two completely seperate companies.
@frankklein487210 ай бұрын
Two brothers, each own one
@nigelmchugh554110 ай бұрын
@@frankklein4872 Nope, that's a common fallacy. You are perhaps thinking of Adidas and Puma, each owned by German brothers
@jeffoleg488110 ай бұрын
@nigelmchugh5541 no it is two brothers also research
@Finglesham9 ай бұрын
NO!. Aldi split into two so that one had a company as did another. Lidl was founded at a completely different time by Dieter Schwarz. The companies do have similar trading polices of course which leads those with little knowledge to assume the companies are linked. Not so.@@frankklein4872
@azza17938 ай бұрын
Wtf you show that you bought super glue but no one actually know if it is any good or bot because you dont show us. Switched off at that point as i can guess the how the rest will go
@paulthomas384110 ай бұрын
Germany is where their tools are made
@BobMuir10010 ай бұрын
Not all of them, even German companies are outsourcing to China. Bob England
@frankklein487210 ай бұрын
Nonsense, I know
@BobMuir10010 ай бұрын
@@frankklein4872 what do you mean? Please help me learn, if I am wrong I need to know
@brickleyyard496610 ай бұрын
Hope no k e is foolish enough or is desperate enough to ever have to consider thies Thay are not tools thay are toys Plenty of good secondhand name brand tools from the likes of cash converters I have managed to get some good makita tools that have lasted Plenty well for around the home DIY thies I wouldn't even say the crappie tools
@bayadere830810 ай бұрын
Cash Converters - secondhand with no guarantee - yeah, okay. Same as Gumtree with a percentage of their tools having arrived from the back of someone else's van. I have built a two room extension using only my Parkside 'toys' from the ground up. They also have a three year guarantee. You buy Makita tools for 'around the home' do you? Where do you live, in a Norman castle? It strikes me as odd that know all know nothings bother to watch videos such as these. Your literacy level prevents me addressing the rest of your comment.
@davidworsley79699 ай бұрын
Cash converters give a 1 year guarantee @@bayadere8308
@prof2bobajob.klonded510 ай бұрын
The drill dust collector looks like a butt plug😮
@frankklein487210 ай бұрын
Explains why yours looks like an elephant's arse, maybe you need sewing back up 😂