Changed out a wire on the harness that was jacked up. Also turned low speed idle out 2 more turns as suggested by someone on iboats. Seems to be OK.
Пікірлер: 48
@tonyn.46633 жыл бұрын
This video is been 8 years! And thank you because of this video it save me alot of headache with my 1998 johnson 50hp I turn the screw just like you said 4 round and now it run good!! Thanks
@davidbean14465 жыл бұрын
I have a 1970 Evinrude 33 hp and today I learned it is possible to have something as simple as a plug wire to make your motor misfire under vibrating (motor running) conditions, even tho you test for continuity and it passes it does not mean it works at all times during running motor. Before I figured it out I was out two new coils, 2 point sets , 2 condensers, and 2 plugs.... now I’m trying to figure out how to lower my rpm’s on this single barrel carb.
@dadtodc12 жыл бұрын
Thanks! I am excited to see it run in the water
@charliegodwind39365 жыл бұрын
I have a 64 Johnson 18horse and was wondering how to set the idle.
@geetarnut7 жыл бұрын
I'VE BEEN SPECIALIZING IN JOHNSON & EVINRUDE MOTORS FOR 28 PLUS YEARS, AND THOSE MOTORS IN PARTICULAR! THE 25/35 SERIES AND THE 9.9/15 SERIES. IT'S A COMMON THING TO HAVE TO TURN OUT THE LOW SPEED NEEDLE VALVE A FEW TURNS BEYOND THE NORMAL "1 1/2 TURNS", AS THE FACTORY RECOMMENDS. AND SOMETIMES IT'S BECAUSE A MOTOR MAY HAVE WEAK COMPRESSION (AROUND 80 TO 100 PSI!) AND THEREFORE CAN NOT DRAW THE FUEL PU FROM THE CARB. DRAW TUBE LIKE A MOTOR WITH 130 OR BETTER COMPRESSION CAN! ASSUMING THE CARB. IS CLEAN AND FLOWING RIGHT, AND COMPRESSION IS 120 TO 135 OR HIGHER, THE NORMAL SETTING OF 2 TURNS OR SLIGHTLY LESS SHOULD SUFFICE.
@dadtodc7 жыл бұрын
Sonny Cannon thanks for that Information. as I mentioned before the video was made so that I could post the link on iboats for help. I had to make a KZbin link to share. I needed someone with your knowledge to listen to what it sounded like after I adjusted it per the instructions from the people that were helping me on iboats. thanks for not being a troll and trying to knock a video.
@geetarnut7 жыл бұрын
Hi Chris! Glad to help out! I am a super fan of 2 stroke motors, and for good reason! They are the very best of all! The evinrude e-tec is in a class all by itself! Nothing comes close in weight, torque, rpm, and reliability! I enjoyed your video Chris! Best of luck boating!!!!
@willwork2fish2617 жыл бұрын
I could use your help sir if you get a chance to read this or the guy that made this video. what's your Facebook I'll send u a message
@geetarnut7 жыл бұрын
Hi Scott, what's your issue?
@willwork2fish2617 жыл бұрын
Well I have a high idke issue, had a guy helping me online but he quit messaging me... I think I'm up a creek now, (screwed it up) he had me mess with the linkage and the cam and roller. Is there any way I can contact you better?
@rdnprops7 жыл бұрын
Why would a timing light show an uneven Firing on #1 cyl on a 25 hp omc Like it's firing to many times /erratic I changed out little brain box that goes to the coils And it's still misfiring at lower Rpm Thanx
@stephanlokkee7 жыл бұрын
hi i have a 8 hp jonson and it consume a lot of fuel a 15 hp of any make consume less than my 8hp johnson.i had a look today and noticed that that the air screw was comptely shut..do u think its that the problem?i turned it 3 turn anticlockwise..do u think it was that the problem of hi fuel consumption..thks
@newyota18 жыл бұрын
what screw do you adjust.?the one on the front of carb?
@chrisellwood35233 жыл бұрын
I have an issue whereby since having a float valve screw drilled out it wont idle and will only run top end with choke on. Maybe this hack is required to get around that chamber blockage. I will try later
@willwork2fish2615 жыл бұрын
So what we your motor doing before you turned that screw?
@christoferbartlett94913 жыл бұрын
Great, but it doesn't show how :(
@aimeeemily7 жыл бұрын
what is the model number of your motor and what would be the number on your electric starter ?? My dads number is worn off and he wanted to know,he has the exact same one as this.
@retardsofnorway92277 жыл бұрын
how many turns out is the screw?
@Farmer24927 жыл бұрын
Hi fantastic video i have a 2000 model Johnson 25hp is there to screws to adjust which is the low idle and high idle and how do you adjust them thanks
@dadtodc7 жыл бұрын
I made this video to post on iboats. there are two of them. a before I adjusted which I posted and asked for help like some of you have. this one was after someone told me what to do. I posted this one to same thread so the next person that needed help might see it and fix their issue. I bet the ones of you on this thread that have condemned the video or had some negative comment are actually HACK MECHANICS that can't stand it when somone doesn't need their advice or fixes something simple that they would charge a person hundreds of dollars to do. I know it has to be hard to troll youtube, and even harder to see someone succeed where you have failed some many times. why are you even watching my video? I bet I know! you have told someone your gonna rebuild a carb, but that wasn't the problem was it? so now your frantically searching videos to help you fix the issue you created. get a life you stupid trolls.
@dadtodc8 жыл бұрын
yes sir yota
@zachhoyt928 жыл бұрын
so how many turns in all?
@dadtodc8 жыл бұрын
I screwed it all the way in amd then backed it out 4 complete turns. then cranked. I turned it out until it leveled
@zachhoyt928 жыл бұрын
okay yeah ive heard 2 turns out is the start point I was afraid to go more then 3
@dadtodc8 жыл бұрын
try two. then adjust.
@dadtodc8 жыл бұрын
+chris Byers I started with two, but it ran rough. I went to 3 and then 4. 4 was the ticket. I did adjust back just a hair.
@redorrick4278 жыл бұрын
video was not a waste of time ,since my 1980 johnson runs best at 4and half turns out
@dadtodc8 жыл бұрын
thanks.
@zachhoyt928 жыл бұрын
how long have you ran it at that ?
@dadtodc8 жыл бұрын
a few years. until I sold it. still running that way. my buddy bought it. there is a very fine line between the rough and clean run. I just kept playing with it until I hear it run fine.
@dadtodc8 жыл бұрын
kzbin.info/www/bejne/h6qQnIiumtdrebM here is the motor on the boat shortly after is did this. I know it doesn't show the motor, but it was on a 15ft sea nymph. ran great
@thomasflynn6427 жыл бұрын
i didn't see you do anything!!!
@zachhoyt928 жыл бұрын
mine is a 85 25hp 1/2 turns runs the best for some odd reason
@dadtodc8 жыл бұрын
I started with the half turns. Couldn't get it to do anything. then I ran it all the way in amd kept backing it out until it cranked. then adjusted from there.
@zachhoyt928 жыл бұрын
Hmm thats odd
@dadtodc8 жыл бұрын
Everything was odd with that motor. Fow whatever reason the motor ran great when out 4 turns. Like I said I ran back in about a half once in the lake. But it ran very fast and never had a cranking issue
@gwgicu9 жыл бұрын
WTF????????????????????
@richarddegen61847 жыл бұрын
still runs like crap
@rdnprops7 жыл бұрын
Why would a timing light show an uneven Firing on #1 cyl on a 25 hp omc Like it's firing to many times /erratic I changed out little brain box that goes to the coils And it's still misfiring at lower Rpm Thanx
@KollynJ27 күн бұрын
I’m assuming because the timing was off? Haha what was your solution