After The Tinning Part Three

I share the set up the assembled poured shell of the tinned babbitt bearing, in the Clausing lathe. Bore it to size and show the results at the end. Just like the 5-inch bearing we re-poured last week this 6-inch bearing is for a marine shaft. One other difference between sizes is this run in an oil bath versus the other being a grease lubrication.
turnwrightmach...
jobshopusa.loc...
mewe.com/keith...
rumble.com/c/K...
Made in China is a warning!
Vote MAGA 2024 #TRUMP Make America great again!

[@TABRO284]

Keith you are an American Hero. These videos are invaluable.

[@jrehtil1494]

What a great series very informative, thanks Keith

[@KeithFenner]

Glad you enjoyed it

[@chieft3357]

I watched all the videos for this project and I really enjoyed every bit of it. From what you showed us as a finished product, I don't think anyone else could have done better. All the best in the future.

[@KeithFenner]

Glad you enjoyed it!

[@peteengard9966]

You can't argue with the results. Great series. Thank you Keith. Stay cool.

[@jamesreed6121]

Great series, I almost feel like i could pour a Babbitt bearing myself. Thanks Much! KOKO!

[@scottthomas5999]

Amazing!! Great workmanship.

[@CraigLYoung]

Thanks for sharing 👍

[@jeffo881]

beautiful surface finish, thanks for sharing.

[@johnlee8231]

Hope you'll share with us Pearls rebuild finish. Looking forward to it.

[@brmllc6444]

Great to see the flag brother. I have problems with our customers complaining about our flags flying hi in our shop. After 30 years here in Illinois we have made the decision to relocate to Indiana. God bless brother. Chris

[@KeithFenner]

Put a three foot circle around yourself and anyone's opinion of you, outside it, is none of your business. LOL

[@Crusadermachining]

Good idea moving. We hate our blue state too, just too much family to move.

[@joemeyer6876]

Great Babbit Series. . . I miss Pearl

[@ÁREAJ27]

Olá amigo Keith, seus trabalhos pra mim sempre são inspiração!!!Grande abraço e boa sorte sempre até o próximo trabalho!!!

[@franksmodels29]

Great vid 👍🏻👍🏻Trump 2024 🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸

[@Hoaxer51]

Yes, get out and vote!

[@30timson]

Здравствуйте, хорошая работа Россия за Трампа! 🙏

[@fainderskurs-koi8767]

Лайк

[@michaelgould5467]

"Wicked Good Lob Lot bungees" good until you leave them in the sun. lol 😁

[@bernardwill7196]

Great series and a good idea to take the lathe as a HBO replacement.

[@tmptorneria1818]

Hola amigo keith que trabajo. Hermoso para que son los cojinetes de q maquina? Saludos amigo

[@GeneralElectricCNC]

Nice finish with no porosity! Any bigger and I see a Kwik-Way boring bar in your future!

[@waynespyker5731]

See Keith's vintage videos from his old shop for more line boring and fixturing.

[@MrAchmad60]

Thankyou. like line boring

[@susannovotney1903]

No shims??????????? Maybe not needed because of the oil bath?

[@mrlithium69]

You could have recycled the babbit chips and remelt them for later

[@KeithFenner]

That is a given, I always clean lathe and chip pan and then it's like no worries and grab it after your totaly done.

[@jeffo881]

during initial run in do you gain more oil tolerance???????

[@KeithFenner]

I bored it to start with .002" oil clearance

[@COLINJOHNS-x5e]

LOVE THE MAGA AND IM FROM ENGLAND.

[@newlifeforvintagewatches2732]

Trump 2024 . Make America great again ❤❤❤❤

[@tylerhensley2312]

How is a dictator going to make America great again?

[@Hoaxer51]

We all need to get out and vote for Trump and to keep the House and take back the Senate!

[@garybrenner6236]

@@tylerhensley2312 Was he a dictator the last time he was in office, did we have two wars going on, did we have millions of illegal aliens flooding our country, could you afford groceries and gasoline? He said he would be a "dictator" on his first day in office by reversing Biden's foolish policies on day one, in response to a reporters question, so the fake news took that and turned into "Trump said he was going to be a dictator"! Do you really think if someone was going to be a dictator that they would tell you? Stop listening to the fake news and use your head!