Tim klošarima što grebu aute ključevima treba lomit ruke javno nasred trga.. svaka čast na poslu 👌
@Amddetailing2 ай бұрын
Dzaba toga uvijek ima
@darrenmetal33382 ай бұрын
Keep uploading these amazing vids please. I've learned so much already. Your skills are from another level as it seems
@Amddetailing2 ай бұрын
Tnx my friend
@mkprodetail87142 ай бұрын
Brilliant work. Very well explained. Saved the customer a fortune. We have learned loads from you. We even purchased a uv scangrip lamp and uv lacquer after 1 of your videos. Well done, keep the videos coming
@Amddetailing2 ай бұрын
I am glad that you are another one of my followers who have been helped by my videos keep it up
@angelcolon202627 күн бұрын
Looks amazing. Thanks for the upload
@Amddetailing27 күн бұрын
Tnx and enjoy
@mnap892 ай бұрын
You can see the scratch becasue applied paint is softer then what is on panel. So when you sand it down smooth, you will remove "new" paint quicker during polishing becasue it is softer. In good light and viewing angle you can see how light reflects in the groove. Anyway - its a good job, and much better than having scratched car and cheaper than paining whole panels.
@chrissimon84032 ай бұрын
Great work from a professional!!
@Amddetailing2 ай бұрын
Tnx
@Tonino592 ай бұрын
Lo ripeto ancora, sei molto ma molto bravo, immagino quanti anni di esperienza hai per questi risultati eccellenti. Ti abbraccio fratello, Saluti dall'Italia
@OZIO842 ай бұрын
You are the best!👏😲💪
@bradymorse88482 ай бұрын
Another great job!
@Amddetailing2 ай бұрын
Tnx
@Mr.johansson2 ай бұрын
Great job master Alan ..you are 👑
@Amddetailing2 ай бұрын
Tnx my friend
@SLYDIT2 ай бұрын
Use a tungsten block to cut bach the paint initially. Theyre specifically designed to knock back paint runs without taking off so much clear around it
@yeungkawo2 ай бұрын
Your video is great , very informative , Thanks!!!
@gbitpal2 ай бұрын
Link to the needle paint tool plz.
@Amddetailing2 ай бұрын
Tnx bro
@RakicFarbanjeKlavijatura2 ай бұрын
Nema boljeg majstora za poliranje! Svaka cast! Nema te nesto u grupi Lakiranja na fb? 😀
@Amddetailing2 ай бұрын
Heheh hvala ti ,a nemam vremena iskreno zavrsavam obuku za PDR pa sam slabo aktivan
@RakicFarbanjeKlavijatura2 ай бұрын
@@Amddetailing primetio sam alat na zidu.. super, jedva cekamo snimke i za to 😀
@Amddetailing2 ай бұрын
@@RakicFarbanjeKlavijatura da uzeo sam nesto od alata i zavrsavam tu obuku pa cu gledati i to predstavljati na kanalu da olaksam ljudima kojibse mislie ovim baviti
@fraizer26002 ай бұрын
super work but can you please explain us why this time you dont use the Micra yellow scrap tool ? you use directly and only sand paper. thank you for your answer :)
@alisomji32942 ай бұрын
Yeah, I like to know the same
@Amddetailing2 ай бұрын
it is explained in the video that it turned out to be much better to remove the filled case with water paper when it is done
@fraizer26002 ай бұрын
@@Amddetailing can you please explain for what reason is better ? I dont notice an explanation in the video why scraping with micra is less good in comparaison of wet sanding :)
@Amddetailing2 ай бұрын
When the lines are shallow and thin, the Mirka scraper knows how to take out the color you filled and you have to repeat everything, Mirka is a good thing and I use it, but when the lines are wide and there is more material to sand
@fraizer26002 ай бұрын
@@Amddetailing when the ligne are more deeper with more material to put the risk to use a Micra scraper can remove the paint ? This why you use sand paper ? Thank you ;)
@pcdetail6022 ай бұрын
Great video.. what's the ratio on the mixing of hardener and paint and clear all together ?
@user-uk5qk1zo4k2 ай бұрын
Clean job 🖖🖖🖖🖖🖖
@Amddetailing2 ай бұрын
tnx bro ad enjoy
@markosokcevic3209Ай бұрын
Omjer laka i hertera 1:1, a koji je omjer baze i njih, isto 1:1? Video je super
@JaguarPaw12 ай бұрын
Great job can I do this with spray paint from a can?
@Amddetailing2 ай бұрын
you can't spray
@mrBDeye2 ай бұрын
This is the notorious deep key scratch caused by cheating lovers or hateful neighbors. Sometimes this damage is done to the wrong car.
@Amddetailing2 ай бұрын
Hehehhee
@tumypavel2 ай бұрын
Great result. I have an touareg also with same damage on fender and i want to do it by myself. Because your videos i start to polish/repair my cars and buy a lot of staff for it 😅 I have some problems in purchase the paint. What should i buy? 1k or 2k paint?i need to use thinner? Thank you!
@Amddetailing2 ай бұрын
the base is used 2k, it is diluted with an acrylic thinner, if you use an acrylic base, then the absorbent goes into it and that's it
@tumypavel2 ай бұрын
Thank you!
@admir19432 ай бұрын
Doktor 👊💪☝️🥇🏆
@Amddetailing2 ай бұрын
😘😘😘
@Super-lucky-77772 ай бұрын
Subscribed to learn more
@Amddetailing2 ай бұрын
Tnx my friend and enjoy
@carlifegarage2340Ай бұрын
Where do you buy acrylic lacquer basecoat?
@calimeroBiH2 ай бұрын
Odličan posao odrađen. Radiš li lakiranje komplet branika ili samo parcijalne ispravke ovakve vrste? Pozz
@Amddetailing2 ай бұрын
Hvala ti,ne bavim se lakiranjem
@rob0618832 ай бұрын
Wowww awesome I wish you were close by me
@Amddetailing2 ай бұрын
Tnx my friend
@DatBoi-mz7pp2 ай бұрын
Nice upload as always! One question, why didn't you used the UV Clear Coat this time? I've noticed the repairs with the UV Clear are usually better than with standard clear and hardner combo. Cheers
@apollo57512 ай бұрын
I've tried locating UV cured clear in the USA to no avail. I've asked major suppliers personally, nope.
@Amddetailing2 ай бұрын
I could do with that too, but since it's currently autumn and there's less sun, it's immediately more difficult to dry with a UV coating, and it takes a long time to dry with a lamp because the damage is quantitatively large
@Actufoot12 ай бұрын
very good job you mix the base with the varnish directly?
@matteomontagna77602 ай бұрын
I'm curious to know too
@Amddetailing2 ай бұрын
Yes
@zzo2818 күн бұрын
Why did you not use Mirka Stain File but sandpaper to paint leveling ?
@Amddetailing13 күн бұрын
Because it wasn't dry enough and the Mirka file would just rip the paint out of the filled part, it can be used when it's dry.
@zzo2813 күн бұрын
@Amddetailing Thank you. So if filled paint is dry , Mirka is better?
@Amddetailing13 күн бұрын
@zzo28 yes
@LordAleksey2 ай бұрын
I have a same problem with more difficult paint condition (17yrs old paint), when i polish it some of clear coat going bad, i think cant do same repairing job like the video
@DetailingTurzovka2 ай бұрын
Hello. Very nice vid. I use 1 part base 1 part clear 1 part quick hardener Most of the times i cant fill the scratch fully on 1st go. When it dries, i can see how the color settled down. I'm applying maximum amount. If i add more, it would spill. The paint is thin after some time on the open. Shall i wait longer for thicker substance? Thank you :)
@Amddetailing2 ай бұрын
It is always filled thicker, from the first time, it is never directly touched to the damage, when the paint is applied to the damage, you have to remove a few millimeters and let the paint fill it by itself. I always leave it to dry for at least 4 to 6 hours
@ramazangunes35992 ай бұрын
What is the professor dye mixing ratio
@Jopakilo2 ай бұрын
Looking for Pdr on door edge
@user-pg5ln2yj1q2 ай бұрын
This is Korea. I want to learn the skills of the teacher. What should I do? Please teach me.
@Amddetailing2 ай бұрын
You have a lot of videos on my channel and in each one it is explained how to do what
@user-pg5ln2yj1qАй бұрын
@@Amddetailing Thank you for
@ForEvolution2 ай бұрын
why no clearcoat ?
@AmddetailingАй бұрын
everything is mixed together, follow the video carefully, everything is explained in it
@chitotanada13892 ай бұрын
how much do you charge for this kind of job?
@Amddetailing2 ай бұрын
400 euro
@e630fnr2 ай бұрын
@@Amddetailing Roughly about the same money would cost to paint the two doors and fenders in Greece where I live.
@Amddetailing2 ай бұрын
it's not a problem, the problem is that people don't want to paint the entire element and spoil the factory coating, because later they have a problem when the car is sold, because more and more customers think that the car was in a big accident as soon as it was painted. Put yourself in a situation when you are buying a car and you see that something has been painted, you immediately have doubts and avoid such a car.
@Bull1the1Great2 ай бұрын
Sto znaci PDR ? ( X DENT REMOVAL ) . Tata mata ko i uvijek
@Amddetailing2 ай бұрын
Paintlless Dent Removal ili uklanjanje udubljenja bez farbanja
@rob0618832 ай бұрын
Do you have an email address I would like some advice I have with my Honda odyssey ?
@Amddetailing2 ай бұрын
Yes tataragicalen@gmail.com or fb page Alen Tataragic
@NarcFreedom23 күн бұрын
The AI narration so bad. Your voice is better.
@Dagadaga1Ай бұрын
Vi ste rođeni na balkanu haha ?
@AmddetailingАй бұрын
Da sto
@Dagadaga1Ай бұрын
@@Amddetailing negdje sam vidio komentar na nasem jeziku pa gledam jel translate ili hahahaha
@chops64742 ай бұрын
Kudos for trying, but this really needs 320g, sealer, blender, 2BC, 1 orientation, 3 CC to look right. The scratches are extremely obvious and jump out. Cheers
@irollon26s2 ай бұрын
@@chops6474 what’s all that?
@Amddetailing2 ай бұрын
yes, it can be seen from 5 centimeters from the car and it looks like a scratch made of wood and because that side is polished and there are no scratches on the coating caused by washing and the color is refreshed, but after a few washes it will all blend together and not be noticeable
@lieberfreialsgleich2 ай бұрын
Next time, use less paint! Maybe 10% of what you showed. I do it in 2 steps, first colour paint, than clear