Alternator Repair Noisy Bearings Replacement

[@ToyManFlyer1100]

Hummmph...Nobody ever shows using the old bearing to push the new one back in....Inspiring!!!...👏👏👏🥂🥂👍👍👍💰💰💰

[@coreyreum4107]

I wondered what went into doing this. After watching, it's not hard to do but I would definately keep buying new alternators due to the amount of time it takes. And, I don't have a press, good video!

[@GorrillaFastTv]

Don’t need a press , harmonic balance puller works just ass good

[@chrisfort7340]

Well done! Thank you very much for your time and know how to make this video!😎👍

[@mazherarif9065]

What's the bearing numbers?

[@carleynorthcoast1915]

I'm not sure if this alternator would work because at 10:04 he is using the inner race to drive in the outer race which causes damage to the bearing

[@AwsBadr]

It will work. Would be better if he placed a metal piece to spread the pressure.

[@benjaminzhou9503]

…. It seems to be a lady working on it, making the job even more admirable. Not sure though. The person was using the old bearing to drive in the new one. So didn’t need to worry about the old one getting ruined. I would put a thick piece of medal over it though, to push directly against the outer race on the new bearing’s outer race. Great video, very inspiring! Just need to make sure to use quality bearing, not all bearings are made equally well.

[@theakh4238]

Use heat on the aluminum housing, and support the backside of the bearing housing my dude. Its very easy to deform or even crack the alternator case pounding it the bearing out like that.

[@DIY_ALAM]

Thanks for the tip

[@dustyfruitypie1633]

What make of bearing do you recommend? Excellent video by the way

[@andykim681]

This is such a great video. Thank you very much for your effort to show how to replace it. I have a question about the replacement. Can you tell my what are the bearing size and any website address i can get the bearing?

[@twinturboranch454]

where do you order your bearings?

[@corsaire2644]

Trop fort! Bravo !!!

[@jagvolvo33]

what sort of noise for bad inner bearings ,if any? im just about change clutch pully but wondering about inner bearings now ??

[@DIY_ALAM]

Like grinding noise you can hear in the start of the video and after changing bearing.

[@jagvolvo33]

@@DIY_ALAM so that noise was inner bearing deff not the "outter " clutch pully?? btw thanks quick reply

[@jagvolvo33]

@@DIY_ALAM also is it load all the time when driving ?

[@michaeldavid3672]

Where can I buy the bearings and what part numbers?

[@DIY_ALAM]

Ebay

[@desimundavlog773]

How to know a Pulley was good or bad ??can u explain it plz

[@jesusp.7774]

The noise

[@peblum]

Why not replace the pulley while you're rebuilding. Thanks for the video, I'm learning!

[@donald8354]

If the pulley is good why replace.

[@Dassick89]

Because they cost the same as a whole alternator lol.

[@Skandalos]

I wonder if I can do this without a press.

[@stevenbean9706]

ordered a bearing puller i couldn't get the inner bearing off by simply prying it buying every tool imaginable so i dont get stuck when i rebuild the next one

[@jerryfitz2002]

Good video but when you put a socket on to hit the bearing out without any support under it that bearing or housing will no longer be true. Gauge it and I bet it’s out of spec.

[@allthentikmusic5617]

Can i call you i have some questions

[@carllinden533]

I hope my Trabant 601 alternator is easier. I don't have a press

[@constantinchivu583]

Greu fără presă

[@frankensteinrules6511]

BEST VIDEO ON KZbin!!!!!!!!!!

[@39FORTYWATER]

Thank you for demo

[@dennisshaw1195]

Great job

[@Imran-gu6gs]

Good

[@sultan26706]

Perfect thanks

[@videoworks7731]

thank you

[@Dr.JHIrons]

I’d just purchase a new alternator..

[@vr6swp]

For my car, a rebuild kit with bearings, brushes and a new back cap is about $40 plus an afternoon’s work. New alternator is about $150-$200 plus core charge (and shipping both ways). You decide whats best for you

[@stevenjosephs9]

Right , Remanufactured are crap ( shit )

[@jesusp.7774]

And sometimes the aftermarkets are weaker on amps

[@Surendarghorela]

Boss use gloves??????

[@constantinchivu583]

Greu cu mănuși mai ales la lipituri colector și perii