Hydraulic Clutch Overview

  Рет қаралды 48,301

American Powertrain

American Powertrain

Күн бұрын

Пікірлер: 14
@mikestannard7128
@mikestannard7128 6 жыл бұрын
Absolutely one of the best after market kits I have seen. Everything you need is enclosed my contact Greg Fetner was extremely helpful. I f you are considering this conversion look no further. I installed on a 1963 Falcon with a 351 and a 5 speed
@gc3022
@gc3022 Жыл бұрын
1992 chevy k1500 nv4500, changed master and slave cylinder, and clutch kit, throw-out bearing, pilot bushing, flywheel, clutch and pressure plate, blew out 2 slave cylinders, first one split on casing (plastic), the 2nd (Luk) one gave out replaced seals from the plastic one, built pressure, lasted 1 drive then gave out too, haven't seen where it's leaking from yet, any ideas, or any recommendations on a heavy-duty slave cylinder
@harrygearhart4520
@harrygearhart4520 Жыл бұрын
Is a hyd. conversion available for the SM 465 truck trans used in Chevy trucks?
@BKMDano17
@BKMDano17 3 жыл бұрын
Setting up a tremec behind a 460. Would like to do this but I hear it's almost impossible to bleed this set up. Thinking I would be better off with a slave cylinder??? Thanks for the video
@danieldonahue3293
@danieldonahue3293 4 жыл бұрын
great info...math and display...very clear science...thanks
@raulmendoza1685
@raulmendoza1685 Жыл бұрын
Good info: would this set up work on a 1052 Chevrolet fleetline deluxe car with 4 speed Muncie transmission ?
@isaiahfelts8799
@isaiahfelts8799 4 жыл бұрын
I needa know if I can put one of them five speeds and if the imput shaft will go all the way in
@astm1554
@astm1554 5 жыл бұрын
Will this work on a '69 Mustang 428 CJ with a four speed toploader and long tube headers?
@AmericanPowertrain
@AmericanPowertrain 5 жыл бұрын
Sure does
@19jody72
@19jody72 4 жыл бұрын
What clutch master can be used with this? 3/4 bore..7/8 bore???
@isaiahfelts8799
@isaiahfelts8799 4 жыл бұрын
Is the crank on the Oldsmobile 455 different for an automatic or standard
@bananaman2184
@bananaman2184 4 жыл бұрын
yea you need to drill a hole in the crank for a pilot bushing
@bassmasterbri
@bassmasterbri 5 жыл бұрын
I think a hydraulic system with an external slave cylinder with a adjustable pushrods and stock self centering style t/o bearing is a more reliable setup....😎
@andyashcroft9316
@andyashcroft9316 Жыл бұрын
did you really say washers????
Hydraulic Clutch Conversion for T5 Mustang Manual Transmission
13:45
Hydramax Hydraulic Clutch Basics & Setup
8:02
American Powertrain
Рет қаралды 32 М.
Support each other🤝
00:31
ISSEI / いっせい
Рет қаралды 81 МЛН
A Guide To Tremec Manual Transmissions
8:14
Holley
Рет қаралды 276 М.
How a Manual Transmission and Clutch Works
10:23
Animagraffs
Рет қаралды 3,8 МЛН
Why is a Hydraulic Clutch Better than Mechanical?
8:02
GM EFI Magazine
Рет қаралды 117 М.
Hydraulic Throwout Bearing Installation Mystery Explained! Ep.72
5:24
Finnegan's Garage
Рет қаралды 264 М.
How To Index Your Bellhousing With American Powertrain
12:21
American Powertrain
Рет қаралды 8 М.
hydraulic clutch install and firewall plate build
12:39
1194video
Рет қаралды 964
5 Tips For Replacing A Clutch
7:04
HumbleMechanic
Рет қаралды 2,8 МЛН