Amr 500 1600vw the design set up

  Рет қаралды 135,262

Joe D

Joe D

Күн бұрын

Пікірлер: 134
@adammiller6606
@adammiller6606 Жыл бұрын
Looks fantastic. Thanks for the upload. 🐜
@martinharris5017
@martinharris5017 4 жыл бұрын
Very nice work! Don't forget some sort of shielding between the undersides of the cylinders and the exhaust J pipes or your heads will overheat! Love the supercharger setup.
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Yea i forgot to slap them on when I put it together hahaha but I got to take it apart to do a few more mods so ill slap a sticky note on it so I don't forget again
@martinharris5017
@martinharris5017 4 жыл бұрын
@@lilcrazyjoe27 Good man! I'm about to fabricate some shield s for my own J pipes, that's what made me think about it :)
@timokuusela5794
@timokuusela5794 9 ай бұрын
Looks awesome. Couple of things, though. That blower takes over 20 hp at the needed rew range. I have seen a dyno video, and the top was about 30 hp. The modern accessory belt was slipping, even with much greater degrees of contact. The v belt will slip. A lot. But , for a 1600 cc engine, the possible 50 cfm or sub 100 cfm will be something. With no belt slip that blower is good for about 300 cfm. At least it may negate the parasitic load of the blower. The other concern is that the oil cooler no longer has the airflow needed for it's surface area, as it is now located to the still air. But, the overall view is just beautiful. Try connecting a timing lamp to the coil high tension wire, mark small dots to the cranckshaft pulley and the blower pulley, and while rewwing the engine from the idle up, observe the "stopping" dots if they move differently at higher rpm, indicating belt slipping.
@lilcrazyjoe27
@lilcrazyjoe27 8 ай бұрын
Oilcooler got changed out back to an original once I got my hands on one. I see what your saying about the rest of it. Would be concerning if it was going to be a drag car or trying to produce top horse power. But it's not... it's a car that's just for fun. To tinker on and screw around with. Not to be the absolute best at what it is. If it was to produce power it would have been turbo and fuel injected
@lilcrazyjoe27
@lilcrazyjoe27 8 ай бұрын
But thanks again for your look into i, it is neat to see how people perceive its built
@miketruchon6525
@miketruchon6525 3 жыл бұрын
when i get it up & running again ill let you know i haven't set my trimming yet but the last ride it made a hell of a difference . pulls like hell throw the gears . ill let you know when im up & running .
@Thefamousmrc
@Thefamousmrc 4 жыл бұрын
Looks like a nice simple setup, good work joe. Look forward to seeing it installed
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
I keep pestering my sister to get on it and finish the rest of the car so we can slap it in and see what it really will do
@Evansthoughts
@Evansthoughts 4 жыл бұрын
Sounds and looks great.
@karlrichardson4665
@karlrichardson4665 4 жыл бұрын
You should have kept the standard cooler and added 1 into the full flow system. The oils only gonna be getting cooled when you’re moving. The standard cooler is has air going over it constantly.
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
i was actually thinking about that when i was putting the shroud on, i'll probably keep the external one but build one that fits in the stock place that flows through and still pushes to the external one all in the same loop. i think i got enough stuff laying around the shop i can build a nice little cooler to fill in the stock hole
@robertbuckles3596
@robertbuckles3596 4 жыл бұрын
Hey there Joe, I love your build! I'm just now at the beginning of a new VW project and this is perfect for what i'm doing. I hope you do not mind, i'm going to build this very same engine just as you have done here. I've gone ahead and subscribed and i'll probable be in contact with you for more in depth specs on this engine build.
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Yea sure no problem I still havent put it into a car yet so it's not fully set up, I still have to modify the distributor to limit its advancement and put a bit bigger jets into the carb, then I think she will be ready to go
@robertbuckles3596
@robertbuckles3596 4 жыл бұрын
Kewl,,, thank you!
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
Hey just checking in on how your VW motor build is going or went, get it out on the road? we still haven't got around to finishing this car off so i haven't got to play with my motor yet. if you got any videos of yours going that would be awesome
@robertbuckles3596
@robertbuckles3596 2 жыл бұрын
I'm doing this TBI unit to bolt directly onto the blower in place where the carburetor would normally mount. I'm using Speeduino NO2C board as the EFI controller.
@jaimemartinez5934
@jaimemartinez5934 10 ай бұрын
Really like that build Where can I get that amr set up if you don't mind me asking
@barryjones1703
@barryjones1703 2 жыл бұрын
Nice setup! I was wondering if the supercharger is still working turning that direction? I have burnt up two of them turning that direction they say it's because they are supposed to go the other way? Thank you
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
no problem yet
@JMC8415
@JMC8415 Жыл бұрын
So the AMR's can be mounted either vertical or horizontal? All the kits I've seen have them mounted vertically. I've been wondering how to get one to fit under the hood and a crankfired ignition will be the ticket if that horizontal mounting isn't an issue.
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
crank fired IGN would be nice, ive seen a few mounted this way, i went old school on this build. just used exhaust piping and built the flanges to mount it, and the runs fine till it hits past 3/4 throttle then the advancing of the dist. gets to high so i opened the side cover and install a limiting screw so it can't advance full when it starts to make pressure. that way i still have good bottom end and top end. if i went crank fired IGN then i could have went fuel injection but i wouldn't be old school then i like it when my setup doesn't look like everyone else. you get alot less people telling you what to do if they don't have your setup hahahahaha
@JMC8415
@JMC8415 Жыл бұрын
@@lilcrazyjoe27 yeah, I started searching more and found a couple others. Ideally, crank fired, fuel injected with a single throttle body all under the decklid is my goal
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
@@JMC8415 can't wait to see what you pit together
@tanveerabbas4272
@tanveerabbas4272 Жыл бұрын
Hey, great work, any HP and Torque numbers to share? Thanks.
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
nope, only rich people do that lol, why else would i build my own make shift set up hahahaha
@bastien73
@bastien73 3 жыл бұрын
Hi joe! How many horse power do you have witb this engine? Do you have more video in your car?
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
the car got put on the back burner for a while, i had a few other projects to get working on, but yesterday it just got pulled back into the shop to finish the pan, and then get the body mounted so we will be a bit before i will have any more info for you guys. i have no clue what it will have for HP as i probably will never get the chance to dyno it where we live im not sure if anyone in this town actually has one either hahaha
@Flash635
@Flash635 Жыл бұрын
Have you considered water injection as a way to retain some of the advance?
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
if it was gonna be a race motor i would look into it, but shes just a boot around town car
@nomadventura8582
@nomadventura8582 3 жыл бұрын
Hey Mr Joe. That's awesome. Do you think you could build a manifolds for a type 4 engines for me. Like the top and bottom , between the carburetor and charger and under the charger. Right now I'm running dual 2 barrels. Maybe I would have to get a different intake. But do you think it be okay with a DB Webber ?
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
If I remember right the intake parts on the head were basicly like the ones on a type one just larger right, you know if you have a exhaust shop in the area you live in that might be a good place to start, just cut up some mounting plates and have the exhaust shop build the intake and have them weld it up, might be a idea, this might be the last beetle I build, I just got into old jeeps recently, got my hands in a old 1949 cj2a
@2stroketurbo
@2stroketurbo 2 жыл бұрын
They say the AMR 500 pulley must rotate counter clockwise , yours is backwards, does it boost ?
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
the way i have it set up yes it does, if i have it flipped over it didn't
@JimsNBHomestead
@JimsNBHomestead 3 жыл бұрын
How does that PCV work? The manifold is going to be under pressure during boost when the blowby is at it's hightest. Also did you account for oil vapours in the blow by gasses? I would think a catch cam system would serve you better.
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
It's plumbed into base of carb so there's vacuum there, it's orficed down so it doesn't suck oil up but has just enough so most of the gasses get sucked in but it's still vented out the oil fill breather, it basicly just takes some of the load off of that breather and helps from making a mess when the breather is spitting oily residue
@matthieudangerous
@matthieudangerous 3 жыл бұрын
Eh I was wondering if the amr500 held up with the draw thru set up. I know on turbos you need carbon seals. Is it different with the super charger? 🇨🇦
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
superchargers are a hole different breed then a turbo, they have had drawthrough setups for eons on these
@serinob4996
@serinob4996 2 жыл бұрын
Sweet set up good job What size jets did you end up running please
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
Not a clue I have never took that carb apart, it came off a 1916cc engine that was in a 365 replica, and I just slapped it on and it worked perfectly for our area I live in hahaha, I broke lucky
@lelohb
@lelohb 3 жыл бұрын
Hi. I from Brazil and i'm interested in doing this in my vw1600. What did you use to adapt the arm500? I thinking in buy te arm500, but I dont know what do to adapt it.
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
i built a plate and intake from scratch, the piping is 1-5/8 exhaust piping and i had a chunk of flat plate steel i traced the amr 500 flange to and made it fit then welded it to the intake i made, tig welded it all together and thats all i got under there
@lelohb
@lelohb 3 жыл бұрын
@@lilcrazyjoe27 Thanks
@miketruchon6525
@miketruchon6525 3 жыл бұрын
i put the amr 500 on my 1600 vw dune buggy & it gave it a very notasble difference but it spins the wrong way can you get it to go the other way . o ps it sized up to the coating on the gear inside came off trying to see about getting warranty on it . any body else have trouble with it i only got about 2 hr run time on it . its still winter hear but the snow has almost all gone
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
I mounted mine how I got it, the first time mounting it realized yup...spinning wrong way hahaha
@t.s.racing
@t.s.racing 2 жыл бұрын
Mike and Joe, the AMR500 will spin either direction and perform the same. I use many of these in motorcycle applications and the unit doesn't care which direction it turns. Hopefully this helps.
@noeemoreno691
@noeemoreno691 3 жыл бұрын
Hi I did the same thing but my get the pulley very hot and I don’t know if is something bad in the supercharger do you ever have that problem??
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
No not yet, you know I never really looked how the front bearing of those little amr units get oiled, does it share oil from the gear box in its back? Or does it just rely on grease in a sealed bearing? That's where I would start looking for the problem
@noeemoreno691
@noeemoreno691 3 жыл бұрын
Is oil bearings in the back the front are seal I replace it and runs good I just need to calibrate the carburetor because need more gas or a bigger carburetor can’t find out yet
@jarteaga9129
@jarteaga9129 Жыл бұрын
Awesome....where did you buy the supercharger?
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
hahaha back when i built this they were on ebay for like $247 canadian out of china rebuilt AR500
@petsb70
@petsb70 4 жыл бұрын
are you gonna put any tensor on the belt?? also what type or measure of the pipe did you use??
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Yea ill be building one eventually , And I went with 1-5/8 exhaust tubing and stretched out the ends to fit over the stock intake bits at the head and slowly honed it out to be a perfect Taper fit when fitted together
@dumpsterfire6351
@dumpsterfire6351 Жыл бұрын
45? Or 90?
@rickeyhobkines147
@rickeyhobkines147 2 жыл бұрын
I need the adapters so I can put my supercharger on. Were can I find em?
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
I hand built my stuff out of 1-5/8 exhaust pipe and some scrap metal I had laying around, fired up the tig welder and pipe bender and expander, then went to town
@eugeneesterhuysen8600
@eugeneesterhuysen8600 2 жыл бұрын
Where can one buy a supercharger like that?
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
I found this one on ebay, it was a rebuilt one from China or Japan, cost when I bought it was only $274 cdn
@panaitlaurentiu5761
@panaitlaurentiu5761 2 жыл бұрын
Awesome build! Will it adapt and work on a 800cc 3 cylinder Daewoo Tico engine? I will go for the same draw through setup you re jamming!
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
i wouldn't have a clue, here in northern british columbia, canada. i don't even think we have seen much for any Daewoo brand stuff other then the odd forklift
@ossgaradeculture
@ossgaradeculture 8 ай бұрын
nice setup. its must be agressive power
@lilcrazyjoe27
@lilcrazyjoe27 8 ай бұрын
not really, basically just took all the lag out of it and sounds fun and looks entertaining hahaha
@ossgaradeculture
@ossgaradeculture 8 ай бұрын
@@lilcrazyjoe27 make more boost with smaler supercharger pulley
@codyfoster7574
@codyfoster7574 2 жыл бұрын
Are you having to run a blow through carb with this set up I’m looking to put the same supercharger on a Datsun 2.2 L
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
if my carb was instream i would have to, but im just running a basic carb up top that i stole off a 1916cc build someone had laying around
@saulsport
@saulsport 3 жыл бұрын
Hello, I wanted to know what happened or how the supercharger that you put few years ago in a video you uploaded worked for you ... if it worked for you you preferred to remove it because it did not give you much hp?
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
i actualy never finished the car yet, was waiting on some parts and im to get them at the end of this month, so i had it on the back burner for two years working on fishing boats and rebuilding some old rifles in the mean time, but i just pulled the car back in to start some prep for when my parts arive, i'll have a update on this in a few month once body is on and i get a seat in place so i can burn some donuts in my parking lot at work
@dennismccain1638
@dennismccain1638 4 жыл бұрын
Any additional input/performance on setup? Nice work
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Its not in a car yet, still sitting under the stairs at the shop waiting for my sister to finish the rest of the car
@hutchtowing
@hutchtowing Жыл бұрын
Well does it still run good? What size belt is that? Do you like it better than the serpentine?
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
never run a serpentine belt, this motor if fun. i'll try and get some video of it one of these days when i pull it back out. just busy building a new radiator repair company thats eatting up all my fun play time
@juniorclassicvwbugs924
@juniorclassicvwbugs924 2 жыл бұрын
Did you have to change the mechanical fuel pump for an electric?
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
i probably didn't have to, but i did, i haven't checked the specs on the flow needed for this carb. so i just winging it lol
@noeemoreno691
@noeemoreno691 3 жыл бұрын
Can you share the carburetor adjustment because my don’t keep running after the choke turn down the car shut off and I try to get more gas and more mixing air but i can’t get it in running to check if is too hi or low
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
I would have to take this apart to get you that, all I know so far is it came of a 1914cc build, I haven't had to rejet or even adjust a single thing it ran perfect so far, but if I do I'll make sure I get as much info for ya
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
Do you have a video of yours trying to run or anything I could see
@noeemoreno691
@noeemoreno691 3 жыл бұрын
I can take a video tonight and send it to you maybe helps
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
@@noeemoreno691 Google up fort radiator Ltd. I'm in Fort st john, find my email there, I'll try and help ya along where I can, two heads better then one hahaha
@davidgorey3366
@davidgorey3366 Жыл бұрын
Where did you run the PCV to?
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
Back of carb, it's nossled down so it can only draw so much and gets just the right amount of negative crank pressure instead of sucking all the oil out and burning it hahaha
@ahmadalbab5448
@ahmadalbab5448 3 жыл бұрын
Love from Malaysia...can 1.6 mpi do this
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
Probably need a bit bigger supercharger for that, since it's a higher rpm engine, this vw air cooled, the amr 500 only big enough to take the slack out of it and pep it up a bit
@mrvolkswagen3362
@mrvolkswagen3362 3 жыл бұрын
That's alot of cam typical to a 10.1 + motor...37 degrees overlap..be interested to know how it works I have same cam in na engine with 10.5 cr...real cool
@lilcrazyjoe27
@lilcrazyjoe27 Жыл бұрын
it sounds amazing hahahaha and with the hopped up springs and junk it screams when you put your foot into it i wish the video would capture the actual sound of this thing
@BackedByFacts
@BackedByFacts 4 жыл бұрын
Hey there, I was wondering where I can buy one for my 1495cc vw engine. If you know pls let me know. Thank you
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
the AMR 500 supercharger i bought on ebay.ca "ebay.ca is the canadian version of ebay" it came from china through that, as for the intake to bolt it too i built that with some 1-5/8 exhaust pipe and some flat steel for the flanges, the super charger comes with plastic flanges you can bolt rubber hoses too and make a set up that way also but i wanted hard mounted, i have seen some kits online that you can buy but ofcourse im cheap and dont want to spend $2000 on something i can make and spent $300 on parts
@dakotamonroe9746
@dakotamonroe9746 3 жыл бұрын
You can also get it through BBM or Amazon now. Obviously my suggestion would be through BBM vs eBay or Amazon. But your call!
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
I was lucky they were way cheaper when I bought ours with shipping included it was only $216 Now I see it's gonna cost someone way more
4 жыл бұрын
Which size is crank pulley for not pass 16000rpm the Aisin 500?
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Crank pulls stock size on engine, aisin pulls is what ever came either it off ebay i never checked or even really cared how fast it was gonna spin really hahaha, I just thought hey I want to slap one of these on and make it fit, thought to my self hey this carb from over here should fit and run about right, you know what I didnt need any fancy math to get it to run awesome either, it just works because its a volkswagon hahahaha
@miketruchon6525
@miketruchon6525 3 жыл бұрын
o i only got up to 3 lb boost with stock pulleys & i have to run supper gas in it
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
Super gas? how's rest or your engine built up? Soo stock pully you got 3psi, k well that'd a good for me to know when I do my mods to my distributor later
@WyldhorseINOregon
@WyldhorseINOregon 4 жыл бұрын
Your progressive carb is a DFAV, which means has an Aqua Choke & you should probably have one with an Electric Choke, since Air-cooled VW's don't have any water system.
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Thanks for bringing that to my attention I never actually check that out yet, I just assumed either it was modified to electric as this came right off a 1914 build and had a 12v power wire plug on it
@wellingtonhonorio8776
@wellingtonhonorio8776 Жыл бұрын
Qual e o carburador
@willybones3890
@willybones3890 3 жыл бұрын
Are you from Long Beach?
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
Nope, I'm way way up north canada, fort st. John, b.c.
@joaoaparecidodossantossant2289
@joaoaparecidodossantossant2289 3 жыл бұрын
Que chik ficou o motor , meu eu tenho um Fusca com o motor simpre, e máquina
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
1600cc, 110 cam, high flow oil pump, carb came off a 1916cc build, high rev springs in cylender head ..... 1600cc, 110 cam, bomba de óleo de alto fluxo, o carburador saiu de uma construção de 1916cc, molas de alta rotação na cabeça do cilindro
@AXLiberty
@AXLiberty 4 жыл бұрын
Action - 3:50
@juniorclassicvwbugs924
@juniorclassicvwbugs924 2 жыл бұрын
ok I answered. my question from the same video .lol
@dakotamonroe9746
@dakotamonroe9746 3 жыл бұрын
What is your compression ratio?
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
Stock
@DavidHernandez-vj1te
@DavidHernandez-vj1te 3 жыл бұрын
Donde consigo ese distribuidor?
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
most parts cip1.ca or cip1.com , the super charger AMR500 was ebay.ca
@marcourielbernalgonzalez2213
@marcourielbernalgonzalez2213 4 жыл бұрын
how many hp have de motor?
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Not a clue yet, haven't finished it, still sitting under the stairs at the shop waiting on the car to be finished, it gets run every once in a while to keep it lubed up waiting and waiting
@davidvanzweel5567
@davidvanzweel5567 3 жыл бұрын
The engine will over heat,under heads and from rear exhaust port to front exhaust port should come in metal covers
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
You can tell it's not a finished build can't ya
@captaincurd2681
@captaincurd2681 4 жыл бұрын
Is the amr500 durable ?
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Not a clue, I will find out tho
@franciscovazquezaguirre9029
@franciscovazquezaguirre9029 3 жыл бұрын
Dónde consigo un motor así?
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
You build it, hahahaha... tu lo construyes, hahaha
@aaaaaaaaaaaaaa4151
@aaaaaaaaaaaaaa4151 4 жыл бұрын
Its interesting how no one is giving up dyno numbers on these AM500 set ups, I suspectthe power is not that much, the AM500 is too small for a engine bigger than 1200cc, you spin it fast & the efficiency falls through the floor.
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
I did see a video where they had a 1600cc build with one and during tune i think they had around 110-125 i cant remember was a while ago i seen the video but its here on KZbin i did see it I'll probably never dyno this one ill just run it by Temps and ear and run the bag off it to see what happens to it.... one day hahaha
@bedlamite42
@bedlamite42 2 жыл бұрын
The stock doghouse oil cooler would work better.
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
I did switch back to it when I installed it into the car
@ParaglidingPanama
@ParaglidingPanama 4 жыл бұрын
Hi, robert buckles. I am also interested in doing a project like yours. I'll subscribe like Joe D did so you can help us both. Congratulations on your project.
@lilcrazyjoe27
@lilcrazyjoe27 4 жыл бұрын
Thanks, my sister made me build this on a whim for her car as she was pissed off i built a car and sold it before she could drive it, now im wishing I built this motor for something I was gonna drive because its pretty dam cool and snappy
@ra8620
@ra8620 2 жыл бұрын
Your supercharger's pulley need small one
@lilcrazyjoe27
@lilcrazyjoe27 2 жыл бұрын
Car is still in build stage, my sister is taking her sweet ass time building it, the motor is gonna dry rot before she's finished hahahha 😂 she's slapping in sound deadening stuff right now so one step at a time...then more engine playing to come
@antbarrimont
@antbarrimont 3 жыл бұрын
W120 cam its too big, power band 2000rpm, W100 fits better
@lilcrazyjoe27
@lilcrazyjoe27 3 жыл бұрын
k, so with a statement like that i would like to know how you came to that. as in what set up were you using and your build and what you found and why you changed and so on so i got a little more to go on and whats different maybe of what you did to what im doing
@upyours1256
@upyours1256 8 ай бұрын
im sorry , but a v belt is not going to to the job 🤣🤣🤣🤣🤣 and your gear reduction is not going to make much compression
@lilcrazyjoe27
@lilcrazyjoe27 8 ай бұрын
neat, lets see yours
Kompressor Haus - VW Aircooled - AMR500 - How to fit Ultimate Supercharger Kit
31:25
Kompressor Haus - VW Aircooled Superchargers
Рет қаралды 39 М.
“Don’t stop the chances.”
00:44
ISSEI / いっせい
Рет қаралды 62 МЛН
99.9% IMPOSSIBLE
00:24
STORROR
Рет қаралды 31 МЛН
Beetle Subaru EJ22 Swap
5:52
Anthony Olguin
Рет қаралды 1,7 МЛН
Super charged Volkswagen motor
1:45
Dr. VDubs Creations
Рет қаралды 205
Supercharged VW Beetle doing Dyno Pulls with an AMR500
10:24
The Dub Shop
Рет қаралды 223 М.
61-78 side draft style supercharger install on Herbie clone....
30:49
Berry's Blowers
Рет қаралды 56 М.