Ansys Fluent: Savonius Turbine Using Dynamic Mesh

[@magicalad1517]

How to obtain the graph of Cp vs TSR in this case from the result ?

[@Kuldeepx]

Hi Thanks for the video. I have few questions. When I tried to simulate the same there is no flow in interior zone of my simulation and in zones I don't see contacts (there is only inlet, outlet ant others). Do I have to manually assign the contact between interior and exterior zone?

[@muhammedcelikyurek448]

Hi.I have the same problem.Did you solve it.

[@gecko_ecco2017]

any of you solved that issue?

[@zhengxin1835]

Change the analysis type from 3d to 2d

[@zhengxin1835]

Watch the video from 4:35 to 4:38. You may miss it

[@nonstop2wheels350]

great video!!!

[@naufalharitsm1576]

Hi, how do you avoid negative cell volume problem? Mine always collapses before it even get to move steadily. Thanks.

[@0oMitchieo0]

Hi I'm pretty new to ANSYS and was wondering if you could tell me how to apply a reactionary torque to the turbine to represent resistance from a genertor

[@plavix2215]

Hi Fluent Setup. This is an amazing video. I have a question for you. I am taking a course in CFD and mesh generation . I just did the elbow mixing tutorial from the fluent manual. However i am working now on a savonius turbine project at the university as a student. How much effort do you think it would take for me to setup a simulation like you did in this video? And what about the computational resources you need?

[@alfaageng]

Hi bro is it okay to assumed two dimensional torque and rpm result are same as three dimensional one?

[@EngineeringwithRosie]

Hi, would you mind if I used the last few seconds of this video in one I am making? I will credit you onscreen and link to your video in the description.

[@fluentsetup1232]

Sure, I think I saw a few of your videos to clear some doubts I had on VAWTs while making some simulations, so go ahead.

[@EngineeringwithRosie]

@@fluentsetup1232 awesome, thanks so much!

[@makavelli9705]

Hey man, i wanted to ask you could i contact you so you might check my 6DOF wind turbine setup?. I am currently stuck on updating mesh at time level N. Maybe you could help me fix it.

[@vivejk4443]

hi, your videos are truly aweome and helpful. i have a question. how do you compile your udf so easily? for me, i have to open VS2017 command prompt and open fluent through that and then still i get errors. how can you compile so easily? it would be truly amazing if you made a video of that or at least reply in this comment. Thanks in advance

[@fluentsetup1232]

I used to have problems compiling the udf. I don't know if this will help you fix your issue, but it wouldn't hurt to tale a look: kzbin.info/www/bejne/rqWVmaF7bsR_mq8 I don't know much about these technical issues, so that is all the help I can offer, I hope it helps.

[@miqdadalazzam]

Cool vidio, how to calculate RPM if turbine hit by wind?

[@alializadeh8195]

Thanx

[@salimabdelli1683]

Still no src and trg terms are appearing in boundary conditions tab of setup. Good morning Mr. I did the same as you did in your video, but Mesh_interfaces are not created in my case. Still no src and trg terms are appearing in boundary conditions tab of setup I tried thrice Can you please help me i tried with ansys 2023 R2 and 2024 R1 student version but i have same problem please help me please please i need a simulation like this for my graduation project urgently

[@m.s.sakib2205]

Delete the contact region in mesh modeling And then create a mesh interface between wall interior, wall exterior

[@yacineboumekouez7718]

hello can you send the geometry please

[@khadijarahal3610]

hello