Anycubic Kobra 2 NEO Unboxing and First Print

[@cpace123]

So I upgraded my Kobra Neo 2 with klipper this weekend to compare the speed with my flash forge 5m. Still not as fast, but much faster than out of the box. Running at 250 in and outer wall what takes my flash forge 14 minutes to print now takes my Kobra Neo about 17 minutes. Before it was taking about 23 Minutes. So a great improvement with not quality loss. Maybe even better quality. And I still have not even attached my AD345Xl to vibration compensation on the Neo. Though I will say it took me a few tried to get klipper running on it.

[@LeeCuriosity]

I will make a video about the comparison of Kobra Neo 2 with Kingroon K3PS pro to see the different

[@ptalten-gz4sz]

@@LeeCuriosity This would be interesting. I have both printers but have not taken the Neo out of the box yet, no room, need to move some furniture around. But I'm quite happy with the KP3S Pro, especially the small footprint and how quiet it is.

[@LeeCuriosity]

@@ptalten-gz4sz I'm edititng a video about kingroon k3ps pro loll

[@jamesjamieson544]

Thanks for this video. I'm a newbie, just got this printer and had many failures until watching your video. Using PLA and your settings, finally got the boat to print, but not after two failures. The nozzle broke the boat off the table every time, so I adjusted the table temp up 2 degrees C and it finally worked. I think a "skirt" around the boat would help secure it to the table better and avoid this problem.

[@LeeCuriosity]

Enjoy the process bro ! There are some problems if the boat did not stick to the bed. Anyway just learn from it

[@MarkHyde]

Found this awesome setup video after order this very printer from Amazon AU - :) Can't wait for it to arrive.

[@SocialSophia]

*are you guys printing via usb or via the included flash drive?*

[@komonekpuzio9098]

Hello, I have a problem because my printer also hits the bed during calibration. I wanted to ask how you edited the settings to fix it? I have a Kobra 2 Pro, so it should work the same way.

[@LeeCuriosity]

Hmm ! Have you increase the Z axis...

[@zoheb4you2002]

I m facing problem in articulated models in this printer.....the lower part of the model is not flexible

[@LeeCuriosity]

Try to increase the Z or turn off the adhesion layer

[@ItzXymz]

Hey for some reason it won’t let me print with my usb-c drive nothing shows up

[@ganeshpingle.8423]

Can you use ABS material for printing.. 🤔🤔

[@lethanhthong3772]

Oke bro ! But you need to add the heat cover to this printer

[@Mecha_Hacks]

​@@lethanhthong3772i am having a hard time printing abs material on my anycubic kobra 2 neo, any suggestions??

[@Kid_illithid]

Does it have a material run out sensor or usb port or anything like that?

[@LeeCuriosity]

It’s seem like have usb port but without material run out sensor!

[@Kid_illithid]

@@LeeCuriosity I got mine setup and it’s printing great. I see there is the E wire, presumably for installing the runout sensor that was mentioned in my manual. My first print was the articulated dinosaur, took an hour and 7 minutes and came out great

[@LeeCuriosity]

@@Kid_illithid It's printing really fast though :))

[@KAUFFMANN7]

3:30 Am I the only one that can't clips this part ? The plug can be clipped in the print head with the two little "tabs" no issue here, but the plastic "protection" doesn't fit at all

[@LeeCuriosity]

What do you mean the plastic protection

[@WorcesterCity.fan101]

Did you have to download the boat or was it just already installed

[@LeeCuriosity]

That’s it :))

[@Bomba_mario124]

I got mine like yesterday and the 3rd thing I made was a rocktapus 😂

[@BushLieWorldDie]

Thanks for your video . This does the job iam getting it

[@biagi1426]

hi, why can't I find the model of the anycubic cobra 2 neo printer on ultimaker cura, can you help me? 

[@LeeCuriosity]

You can create a profile and download it from the manufacture.

[@LeeCuriosity]

store.anycubic.com/blogs/3d-printing-guides/anycubic-kobra-2-cura-profiles?srsltid=AfmBOoq3KrmZrGiTfmhHj0G10aw6cF8Qm969VZL3BDtmvZtPAco1rNXB

[@NIKHILAryan-x9n]

Bro bed adhesion problem pls help me bro😊

[@LeeCuriosity]

How can I help you?

[@NIKHILAryan-x9n]

@@LeeCuriosity when im giving print it strted but suddenly the print was disturbing and removed from that position

[@LeeCuriosity]

@@NIKHILAryan-x9n well it depends on the bed leveling or temperature when you setting for slicer. But I guess that it's because the bed is not flat or you have to adjust the z axis between the bed and the nozzle.

[@LeeCuriosity]

@@NIKHILAryan-x9n Hmm ! I think the distance from the nozzle too high or too low...

[@jamesjamieson544]

Just got this printer and had the same annoying problem. Your bed temperature is related to adhesion. I increased mine to 62C and it helped.

[@JAVINDU2]

Hey i see this printer on ebay for 110 usd and shipping cost 40 and brand new is this orginal price 110 usd (how much you paid for this printer) riply please

[@hammyhamhamsterdailyshorts6554]

i payed about $250 so thats a great deAL

[@kevinthorn9672]

Will this print like a mortal kombat scorpion mask?

[@Icedupdoggy]

Probably