APC 2.2Kva Smart UPS Calibration Problem solve (Battery bar lights blinking issue) MODEL: SUA2200I

[@fantastikusst9307]

Thank You very much for this usefull solution !! My new Battery is now corectly calibrated with your Help. 👍🤩

[@ApcFix]

You are welcome ♥️

[@NnJunejo]

The problem I am facing is related to the battery charging bars on my UPS. When the electric supply is connected, the battery bars indicate the charging level accurately. For example, if the battery is charged to 30 percent, two bars on the indicator light up. Similarly, if it is charged to 50 percent, the indicator shows lights for 50 percent, and when the battery is fully charged to 100 percent, the indicator displays a full bar. However, the issue arises when the electric supply is disconnected. At that point, the UPS battery bars drop to the last bar, regardless of the actual battery charge level. When the electric supply is restored, the battery charging process starts from the last bar instead of accurately reflecting the remaining charge.

[@ApcFix]

Your problem is related to calibration when the UPS calibration goes wrong, the situation you highlighted in the comment occurs.

[@mnobody2533]

brother, you need to change the constraints value and then consider your batteries are new. I recommend a video on "AT Online" This channel helps me a lot even though they provide commands and software links and also explain in detail how you can make a cable for it because with normal cable you can't configure this ups.

[@rafaelvitti8673]

What settings are you using on the serial port? These would be: 2400 - 8 - None - 1 - None ?

[@ApcFix]

Bits per second: 2400 Data bits: 8 Parity: None Stop bits: 1 Flow control: Hardware

[@henrysanusi7441]

@@ApcFix Didn't work for me. tried all the options.

[@wbrione]

Hello @ApcFix. I have this problem on a SUA3000-BR, I don't have the serial cable, but I have the USB communication cable, is there a way to apply the correction, or will I really need a conventional serial cable?

[@ApcFix]

For apc ups calibration you need an apc serial communication cable (APC 940-024c). Visit this website for help: www.eevblog.com/forum/dodgy-technology/scheiderapc-smart-signalling-scam-%28serial-cable%29/

[@lautarosabatini3220]

SOS UN CRACK MUCHAS GRACIAS

[@amak77]

Calibration to be done with All servers/systems out? or can be done when online?

[@ApcFix]

?

[@amak77]

@@ApcFix I mean to do calibration so we have to shutdown our connected servers, or it can be done without switching off?

[@0tv0]

Can I use the Compatible Cable 940-0024C? my UPS is surt1000xli and my PC don't have the Com 9 port

[@ApcFix]

Use USB to Serial converter if your PC don't have DB9 port Visit this website for USB to Serial converter: www.amazon.sa/-/en/Converter-Connect-Installation-Universal-TU-S9/dp/B00BL697VA

[@dalinoino4996]

Sir, how to stop low battery warning on ups apc sua 2200i, any software for it, thanks you 🙏

[@ApcFix]

Just calibrate the UPS the low battery problem will be solved. Software: drive.google.com/file/d/10W1UsnlErNnhvK1E9fgjxIPgBvTiG_c3/view

[@dalinoino4996]

@@ApcFix how to calibrate ups

[@ahmedRashadMando]

i have another issue in my 1k UPS same brand , but its giving error " Red light ok ( X ) with 2 lights in battery bar like ( 00110 ) i check the service manual i found this FAN Failure i changed all damaged components and i measured all resistors , capacitors "changed " , diods , all mosfets and i changed 2 UC3845 IC's and regulator LM317 but still not working , i tried to change the control card i taked from another working UPS , but also not working , can U please support me ??

[@اميرالفوادي]

Please, I need the form of connections, the way to connect to rs232, and what are the commands for the program

[@ApcFix]

For Pinout diagram visit this websites: networkupstools.org/cables.html Commands are different for different models.

[@SamTechEG]

i change my battery 2 100 amp by 2 butthe run time still low any way to fix it

[@ApcFix]

Just calibrate the UPS, and run time will increase.

[@Moroo1976]

thank you for video and the exe..

[@ytmadpoo]

That was weird. I ran the EXE with an SU2200XLNET attached and at first it connected fine but only showed the voltage in/out and load. I enabled those two checkboxes next time I ran it and when I connected to the com port, it shut the UPS off right away. I had to go and turn the thing back on. So that was weird. I'll have to try it again with only one or the other option checked and see which one did that, or maybe it was just a fluke. Edit: I had to remove the network management card, and then it launched okay. I read somewhere that you'd have to do that, and it's true. Remove any NMC when running this.

[@ApcFix]

This is the issue with NMC remove the network card, and then connect the UPS to a program. Network card disturbs the serial communication between UPS and program.

[@chintharamu1356]

In my ups all led blinking problem coming how to resolve it

[@ApcFix]

Watch this video: kzbin.info/www/bejne/p6CzoHmoq6afqM0

[@usamaarfi2045]

Asalamalikum Dear Apc: I ask One question Overall ups calibration use for Software Apcfix please tell me Yes/No

[@ApcFix]

walaikum assalam, The overall UPS calibration software I would recommend you to use teraterm software. Teraterm available on Internet

[@onlinelearning719]

My UPS battery is showing 51.4 vdc and a continuous beep how to fix

[@ApcFix]

Charge the battery to 100% and then calibrate the UPS the issue will resolve. Thanks

[@onlinelearning719]

@@ApcFix how to calibrate my ups. (Apc 1kva)

[@ApcFix]

@@onlinelearning719 ApcFix software drive.google.com/file/d/1f3Bv1GRWf2tKsdrld8faKJS3kJvhPuK7/view

[@thienhuynh92]

link download error, please update it. Thanks.

[@ApcFix]

Link Updated.

[@ApcFix]

drive.google.com/file/d/10W1UsnlErNnhvK1E9fgjxIPgBvTiG_c3/view?usp=drivesdk

[@teguhadja2993]

Please share link

[@ApcFix]

drive.google.com/file/d/10W1UsnlErNnhvK1E9fgjxIPgBvTiG_c3/view

[@bachuynh9970]

xin giá APC 2.2.Kva

[@ApcFix]

pakpos.net/home/42-apc-ups-supplier.html

[@mnobody2533]

bongiya kam or information zyada. ma ak detailed information video dekhi ha "AT Online" channel pr. even normal cable nae use hoti configuration k lia jo cable use hoti wo kesay bnani wo b btaya ha. also provided commands and software links.