Applying Text to a Curve - Part 1

[@jav9888]

4 Years later and still a great VID !! Thanks for all your work

[@jeremiahmort4294]

The information about the start point to change text direction was very helpful. Thank you.

[@rickbrown2600]

Wow, that was SO informative, thanks. I am a brand newby and have been struggling with how to design curved text, your video was excellent, very easy to follow and just the right amount of info to get the job done. Thank you very much, I will be following you from now on and will quit trying to figure this out on my own.

[@keepout3162]

I can't thank you enough Mark. Been watching a ton of these and you have made it so clear. I will be watching more. Getting my CNC in a couple days and I told the wife I would not buy it unless I could learn the software. Well, you have certainly helped!

[@davesimoniette8599]

Mark, Your videos have helped me become a fair CNC user, and I even started a little retirement business making signs. I am sorry to say that I have not seen any new videos, and I hope your doing well. Please know that your work provides a great learning tool to new CNC users, and is a much needed educational tool. I hope to see more videos again soon. Fair winds.. Tight lines my friend.

[@MarkLindsayCNC]

Thank you! I'm all over the place - here on KZbin, Instagram, Facebook, Twitter, etc... I do a weekly LIVE Q&A every Sunday at Noon Pacific time, and try like crazy to post a new video every other week. I don't know why you haven't seen any new videos - I'm making them. I have over 300 on my channel. Remember to Subscribe, then click the notification bell, and set it to All Notifications. Then you'll get a notification whenever I post a video, and whenever I go live.

[@tomleonard9170]

This exactly what I was looking for. I really liked how you showed how to make the minor adjustments and then took it all the way down to applying the tool paths. Thank you so much Mark.

[@MarkLindsayCNC]

Thanks for checking it out, Tom! Glad you found it helpful!

[@Mtbeaver9]

Again another great video Mark. I am learning alot from you my friend. Keep up the great work and thank you for taking the time to do this for us newbies. I really appreciate it. God bless.

[@chuckmoney1688]

Great video. You could also select one of the curves and offset the curve in or out a little and re-apply the text to it to make position adjustments

[@fredsawtelle1833]

Nicely explained. This video told me exactly what I wanted to learn when I went searching for "Aspire - wrap text around a circle".

[@MarkLindsayCNC]

Thank you for the comment, Fred! Glad it helped you out!

[@dalewilliamson1125]

Great Job Mark, simple and to the point. Keep 'em coming!!

[@butchmiller2451]

I could save myself a whole lot of frustration if I watched your always informative videos first. Start point? Well that solved my problem.

[@dohjryt]

Very instructive and clearly stated with helpful variations in the content.

[@MrRenoman2011]

another great Video Mark

[@alankreifels6445]

Good stuff Mark! Your timing as usual was impeccable! I have a customer project coming up that is going to need this!

[@MarkLindsayCNC]

Hope it helps you out, Alan!

[@topcat143]

Thanks Mark. This answered the question that I had in the email I sent yesterday. I have to upgrade my searching skills LOL. YOU ARE THE MAN!!!!!

[@MarkLindsayCNC]

Thank you, Bill! Glad it helped!

[@jondirubbo8929]

Really super job explaining curved lettering. Thank you.

[@sambond7703]

Thanks Mark, always great to learn something new. Do more please!

[@rchavez5056]

Great job Mark. You simplified that!

[@kilroy79763]

Excellent Explanation Mark I proceeded to accomplish the task thanks to you!!!

[@paulleonard2211]

Great video very clear and informative. Thanks

[@jeffreystewart6571]

Excellent explanation thank you.

[@jimshirley2549]

Between you and Vectric, I'm in love!

[@MarkLindsayCNC]

Well, thank you, but I'm already taken... :D Hopefully you found the video useful.

[@amazonprime1804]

loveyou man helping beginners for me

[@glennaadams8412]

you are an excellent teacher

[@ralphhall5001]

I LOVE YOUR VIDEOS, THIS IS REALLY GREAT INFORMATION FOR US BEGINNERS

[@MarkLindsayCNC]

Thank you Ralph! I hope you're finding the videos useful!

[@MikeMerzke]

Great job Mark! I love the details you put into this tutorial. Keep them coming and keep up the good work!

[@ednyegaard9514]

Well done Mark. Good information. Thank you

[@johndobbins2536]

Your the man!!!!!! Just what I needed to watch Thanks

[@MarkLindsayCNC]

Thanks for checking it out, John! I hope it helps!

[@4dan2]

Thanks again Mark!

[@jimking9646]

Another Great video

[@420Heretic]

This video helped me a lot. Thank you very much.

[@mikewalker1512]

Thank you, great informative video, answered several questions for this beginner.

[@MarkLindsayCNC]

I hope it helps you out. Thank you for watching!

[@thomascaves4342]

@@MarkLindsayCNC I will also use this with my High School classes. Thanks so much for this!!

[@dptp9lf]

Video helps a lot! Great job Mark!

[@faisalazeem3574]

good very informative video. in this video you write text in round please tell me where we write border design in round circle in aspire

[@MarkLindsayCNC]

It depends on whether you are using a 2D or 3D border. Here is a playlist of 3 videos that demonstrate the subject: kzbin.info/aero/PLLuYLaC3-QRNJ-wWDOr-PirbGb9xrNE-Q

[@MrJeffery9076]

thanks mark for the help

[@jeffeltiste5557]

mark thank you for taking the time to teach us about applying txt to a curve

[@Gnew111]

Thank you for your time and efforts!

[@MarkLindsayCNC]

Thank you! I hope it helps you out!

[@gussiebanjos7618]

Nice Job Mark- Eric

[@raybesst4648]

Great job Mark. I don't know why Vectric cannot do this and make it easier . You email them and they are not much help. Thanks again for making it easy and simple

[@MarkLindsayCNC]

Thank you very much, Ray. Vectric has to cater to all skill levels in their tutorial videos - everyone from beginners to experienced users who just need a little bit of help finding the tools. They can't take the time to get into each concept, technique, or tool and break it down for the person who has never done this before. I try to do that, because 5 years ago, I was the guy looking for help - and still am at times. I'm not an expert - I'm just trying to help folks avoid the mistakes I've made in the past.

[@davidkelm1356]

Wow. That was SUPER. Thanks so much

[@MarkLindsayCNC]

Thanks for checking it out! I hope it helps!

[@jimscott64]

I'm sorry Mark, I should have written back last night and let you know that I figured out a way to do it that worked fine. I created a circle that I could attach the text to and get it just the way I wanted it. Then I deleted that circle and drew a new and bigger one around it that is the actual diameter of the table top.

[@MarkLindsayCNC]

No worries! Whatever works, you know!

[@danielstein8320]

Well Done!

[@mikebley3918]

Thanks Mark, Very informative, Just do more and good on time.

[@mariewood8267]

Got it figured out!

[@kvloogy]

Would love to see that Oregon University Project you have in you project pane.

[@MarkLindsayCNC]

That's an older project that's long gone. Thanks for watching!

[@HueyF]

Very helpful. Thank you!

[@MarkLindsayCNC]

Thank you for checking it out!

[@rzjjt5]

like your video how would put something in the middle and how would you cut it out v carve or profile

[@MarkLindsayCNC]

Thank you, Robert. You could either import vectors or draw your own, then size them to fit inside the text circle or curve. There are several methods, and I've covered just about all of them in various other videos. Hit my main channel page by clicking my name, and check them out.

[@MegaTopdogs]

Great video Mark THANKS !!!

[@LarryMMackey]

Thanks Mark, good stuff enjoy it!

[@markgraves7972]

Thanks buddy, needed a reminder about the nodes, I was ready to lose it!!!

[@MarkLindsayCNC]

One of the many reasons I post is so I can go back and refresh my memory as to how I did something a year ago - lol. Thanks for checking it out, Mark!

[@markgraves7972]

I was ready to smash something, then I was like my friend Mark knows everything, lol

[@MarkLindsayCNC]

@@markgraves7972 HA! I know enough to get myself into trouble, and where to look to figure out what I did wrong.

[@SharonDenning]

Thank You!!

[@dzee9481]

Very well defined video done with clear and concise instructions. Prefer listening to your video's than those from Vectric since the accent at times is hard to understand.

[@MarkLindsayCNC]

Thank you very much! I hope they help you out.

[@rebaker2012]

Great Job . Thanks .

[@paulinemeehan9446]

Hi Mark, thank you for the video it makes it so simple to follow. I have a problem you might be able to help me with I hope. When I go into wrap a text the areas that I need to change i.e. above a circle or below are greyed out and so is the apply button. It means that I cannot set anything on it, its like it is frozen!!! Any Ideas Help!!!

[@MarkLindsayCNC]

Shoot me an email by going to the Contact Us page on my website, then sending me the message. It'll be easier that way. Thanks!

[@johnhall2806]

This was very helpful. I tried using this for a logo and designed it at 8" diameter. Everything looks fine. I reduced the size of everything to 1" diameter and the text does not carve in the simulation. What am I doing wrong?

[@MarkLindsayCNC]

You're probably not doing anything wrong. The text is probably so small that the v-bit you've selected is too big to carve it. You might check out this video to see what's going on, and how you can solve the problem: kzbin.info/www/bejne/gHiqYayKhc6batk

[@johnhall2806]

@@MarkLindsayCNC Thanks for your reply. I watched the suggested video and understand the concept. However, When I reduce the size of the logo to 1" the small text does not show when running the simulation. I have tried it with 90 degree, 60 degree, and 30 degree v-bits with the same result.

[@twistedworxengraving7920]

Everything was good up to opening up the Curve on a text bar. It will not light up/open up, so I can not make any changes to be able to curve the text.

[@MarkLindsayCNC]

If the text has been converted to curves, it's no longer a text object and the tools used to curve the text will not work. Check out my video on using the Distort Tool. Here's a link: kzbin.info/www/bejne/f4O3moSfr9eUj5o

[@jimsinacola-totallywoodwor7473]

Good job Mark! Don't worry about the time. Thought it very informative.Just a ? Is your highlighted cursor set in Vcarve or is it a system setup?I say keep'em coming!

[@MarkLindsayCNC]

The highlighted cursor is a part of the screen capture software I use. I use a program called Flashback Express by Blueberry Software. It's got a lot of features not normally found in a free screen capture program, and I like it a lot. There is a Pro version that runs about $50, but so far I haven't run into a need for the pro version.

[@U_Kamrc]

Keep going. Nice educ. job!

[@MarkLindsayCNC]

Thank you!

[@jimscott64]

Thanks for another great video Mark. I am making a table top for a store in town. Well, I'm designing it at present. It will be a while before I actually build it. They are friends of mine and it's going to be a surprise. I followed along in this video and got part of the name done. The name of the store is "YORKS PARK GROCERY." I was able to put the name YORKS to fit the 30 inch circle in the top part. But when I put PARK GROCERY in the bottom half, it will only come out in really small text, not the same size as in the top of the circle. Is that normal or am I missing something? I am wanting the text to be inside the circle and not outside like you did, as the circle is going to be the actual table top. Thanks.

[@MarkLindsayCNC]

If you're creating the two completely separate lines of text, you should be able to resize them independently. Keep in mind, however, the text on the bottom will get crowded at the top of the letters, so you'll need to do a bit of kerning to get them to look right.

[@leroyscncwoodworx841]

Another great video. I have a question, I am trying to rap text to curve but the window is grayed out and won't allow me do anything. Where did i go wrong?

[@MarkLindsayCNC]

Is the text an actual text object, or did you convert it to curves? It has to be a text object. If you've already converted it to curves, you'll have to use the Distort Selected Objects icon under Transform Objects, or delete the text and start over.

[@leroyscncwoodworx841]

@@MarkLindsayCNC All is good. I don't know what happened, I exited the software and came back in and all was good. Thanks, LeRoy

[@johndeshiro]

Hi Mark and thank you for this video. I have a question. When create the text and break the block of text into lines and select the text and vector on the top center of the curve and then apply the curve my text comes out upside down and backward. Any idea what I'm doing wrong ??

[@johndeshiro]

Maybe because I drew a circle instead of 2 arcs ?

[@johndeshiro]

yeah still upside down and backward

[@MarkLindsayCNC]

Select the curved vector, and tap N to go into Node Editing. Look for the green point - that's your start point for that vector. Put your cursor over the point at the far left end of that vector, right click, and select Make Start Point in that menu. Tap N to come out of Node Editing and try it again. I covered this at the 6:05 time mark in this video.

[@johndeshiro]

I figured it out. You have to draw two arcs from left to right, one for each line of text.

[@johndeshiro]

@@MarkLindsayCNC 👍👍 thanks

[@TheMinimax0]

Many Thanks helped a lot

[@ronaldleger5871]

Thanks Mark

[@fgschill4766]

Sorry for that. I'm making a sign with text wrapped at the top and at the bottom similar to what you did. I want to wrap circles around the text, top and bottom. I deleted the circle that I used to wrap the text so I would start with a clean circles. Using a 90 degree v bit. It will not carves the whole circle. It stops within an inch. Can't find a solution in the manual, maybe If I keep looking, but thought you might know the answer.

[@MarkLindsayCNC]

The best bet would be to contact me through my website. It would be easier for both of us that way. Thanks for watching!

[@billymorris4273]

Do you have video on how to do raised text

[@MarkLindsayCNC]

Not specifically, no. I don't do many raised text projects. Next time I get one, I'll shoot some video.

[@billymorris4273]

@@MarkLindsayCNC thank you

[@fredwienbarg5051]

Great! Thanks.

[@MarkLindsayCNC]

Thanks for checking it out!

[@robertsnook2701]

When I open the box it does not allow me to curve anything. No options. Your video is spot on right up until i open the curve text box

[@mariewood8267]

I am having a hard time joining the 2 vectors back together. Not sure what to do. Anyone have any pointers.

[@kevinwillis6707]

thanks mark, the node editing got me out of a spot 👍

[@shelby50411]

i think i got it....thank you

[@shelby50411]

hi i have a unique issue..within aspire i know how to wrap text around a curve however i have a vector that i imported and it is letters and i want to wrap them along a curve but im not sure how

[@MarkLindsayCNC]

For that, you'll need to use the Distort Tool. As you've discovered, applying text to a curve only works with text objects. It won't work with vectors. What you'll need to do is draw the curve you want the text vectors to follow, position it where you want the text to be, put the text in that same location, then use the Distort Tool to distort the text above that curve, or between two curves. Here's a link to my two videos on how to use the Distort Tool. (I'd check out the first one first.) I hope they help! kzbin.info/www/bejne/f4O3moSfr9eUj5o or kzbin.info/www/bejne/mZnCaYCfic93nbM

[@JohnSmith-bm8xb]

Why didn't you set a depth when carving the text?

[@MarkLindsayCNC]

In v-carving text, the depth of cut is dictated by the angle of the bit and the width of the letters. In this example, I wanted the bit to be free to plunge as deeply as it needed to go in order to carve the letters in one pass. I could have set a flat depth if I only wanted the letters cut, for example, .125" deep. I didn't have that restriction, so I left the flat depth blank and let the software calculate the depth of cut.

[@JohnSmith-bm8xb]

I guess I don't know enough about v-carving to understand what you are taking about. I just started my build on a 48x48 Garageworx cnc. I do want to do a lot of v-carving, so back to u-tube. I got my edge finder from Bill Briggs can't wait for you to do the video on this setup.

[@MarkLindsayCNC]

I'll do a video on it.

[@MarkLindsayCNC]

The Triple Edge Finder video is coming real soon!

[@JohnSmith-bm8xb]

I can't wait to see it. I still have lots of work to get the Garageworx put together.

[@shelby50411]

this is off subject but related to why i had to do what i had to do to get proper font...why after 50yrs do we still only have a handful of very simple single line fonts to choose from??? why doesnt somebody create more?.. this has always puzzled me.....why arent there thousands to choose from?

[@fgschill4766]

Having a problem.

[@robertsnook2701]

THIS DOES NOT WORK FOR MY VCARVE

[@MarkLindsayCNC]

Relax - I got ya covered. This video was shot when I was using VCarve Pro version 8.5. A lot of things have changed since then. Here's a newer video that covers the newer versions of VCarve and Aspire: kzbin.info/www/bejne/l4arqnagiq6Yp68