Arctic Cat recoil rebuild

[@Froggies505]

Oh my god. Where was this video when I fought with my recoil for hours last night. Thank you thank you thank you.

[@Heavy_Monkey_Arms]

Thank you for taking the time to show the whole process. It made life a lot easier after watching this and replacing my pull cord for the first time.

[@1qikz210]

Thanks so much for this video. I didn't find this one until after a saw another one on YT. Yours was much more in depth and informational. The setting of the spring tension was the key to getting mine back in working order!

[@paulo5861]

Great how to video. Saved me allot of time and effort to replace starter cord. Thank you for doing that.

[@corneliusprice9363]

Great video, explained very well

[@brendanphilbrick301]

Great video dude very helpful rebuilding one quickly.

[@keithpiercey]

Very good video. Clear, concise, good camera work. Clean hands too!

[@seanandvanessacarberry1916]

What did his hands have to do with anything

[@amandasmith6908]

very detailed, would like to see other ways to wind as I can not find that tool

[@brandonhackley7067]

Were did you get the tool for the spring

[@scottwidrick1835]

Question at about the 13 minute mark when you install the pawl does the short end of the spring go into the notch of the pawl? Thanks.

[@herbbarrett900]

Great video how do get one of that tool

[@KedneyContreras-cw5pt]

At last of vid why the rope doesn't go inside of round plastic?

[@jason28w]

what did you use to clean it all up with ?

[@bobaneblaze]

thx i didnt know how the coil or paul went in.

[@avaglass3124]

Can you let me know where you bought the winder used at 7 minute mark?

[@gonzalopa5]

Hi!! I’m having issues ! If I tight the nut the rope doesn’t go back in and if if loose the nut the spring works really good and the rope goes back in but the little thing doesn’t goes out. Help please!! Video call or something ? Thanks

[@jamesgonzalez2269]

Did you figure this out?... I'm having the same problem!!

[@raymugs3036]

Love that tool

[@thatloudfiesta1282]

What’s the name of it?

[@markellis9428]

So how does one get that winder any how ?

[@freezerburn04]

Nice one, thanks!

[@huntersadventures9045]

Very helpful

[@MNDood2122]

Do you need to take the spring out to just replace the rope?

[@powertech2170]

MN Outdoors Yes you do, unfortunately!

[@MNDood2122]

Why? It stayed wound up in the case. I could take out the plastic wheel replace the rope and put it all back together all without touching the spring

[@powertech2170]

Oh yes my bad...been awhile since I did one, but your right you can let the spring wound up. The one in the video had blew apart on the sled before and I decided since I have rewound it I would make a video on it.

[@509FUN]

No you don’t… totally unnecessary just leave the spring in there pull the Plastic round for the rope out carefully and the spring will stay in place. I’ve done many many of these and never pulled a spring out unless it was broken

[@johnnyj7399]

Can you drop a link to the 3d print model, I can't find it anywhere.

[@johnnyj7399]

nevermind broke my spring winding it up rip :(

[@herawen3980]

excellent

[@kimnesvig254]

Nicely done!\

[@nicenonya3]

Ok if you have the fancy tool

[@nathanlear1495]

Hey where can I get a coil spring tool?

[@powertech2170]

Nathan Lear I had mine 3D printed a few years ago. Not sure if you can buy one. There are other ways to do it with a vise grips

[@nathanlear1495]

Power Tech I was able to get it with it inside the housing. Anyway I could get one 3d printed?

[@powertech2170]

I may be able to print it. Although I am not sure if I have the files. I will check

[@briansedgley8508]

where can I find the recoil spring tool online?

[@karsonwebersole9346]

Not sure if there is a recoil tool, this one i used. I designed and 3D printed

[@kenh.249]

@@karsonwebersole9346 "Recoil Spring Rewind Tool" is sparse on the internet. Only one spendy one from Rocwood for $33. You might consider selling the ones you make! Great video.

[@nicenonya3]

my rope just broke,don't use the old rope!

[@camdencollum6251]

I would like to get one of those tools

[@RalphHarrington-jp4ni]

Could you forward the link for the 3d files for the tool please.

[@nilskohlstrom9289]

Thank you!

[@beerealopenyoureyes8587]

Thanks 🤩

[@andrewbacon7958]

I can get the fuckin thing spring into the groove on the disc bruh idk what I doing wrong or if my shit is just broken

[@moimayamahaetmesnounours]

Reconstruction du recul du chat arctique

[@zacharybell5496]

Not being able to buy this tool degrades the usefulness of this video substantially

[@2vintageDeamonFan]

Can I have 1

[@CorvinDalton]

I hate how you need special tools

[@YOumeanMe]

good job.. however couldn't see what you were doing.. due to shadow and poor lighting ..

[@ryansolomon5083]

Thank you!