Arduino Tutorial 28- Understanding How to Use a Stepper Motor

[@darkooslovcan1187]

Incredibly simple explanations, which is very difficult to find on the internet these days. Well done.

[@EnjoyMechatronics]

I am so thankful that you like it 😊

[@olivermurray9874]

Clear and concise. I set my stepper while watching your video and it worked 🙂, thank you for sharing

[@EnjoyMechatronics]

Glad it helped!

[@DGbert]

Thanks so much. This really helped me. I was activating the coils in the order 11, 10, 9, 8 from following other programs but it didn't work. Using your 8, 10, 9, 11 worked perfectly. Why does a sequential order not work?

[@imvincible1391]

Most of my parts were different but the tutorial was so good I could make it work. Thank you!

[@markojotovic8991]

First video where is all explain step by step - thanks, it works well

[@EnjoyMechatronics]

Glad it helped!

[@daironrojasmunoz268]

THIS IS THE BEST VIDEO I'VE SEEN ABOUT HOW TO USE ANY ARDUINO DEVICE!!

[@EnjoyMechatronics]

Really appreciate your interest

[@bouaakilikram7330]

Very well explained! Thank you, just wanna know if using that code, will the motor continue rotating endlessly ?

[@volvo336]

Could you please give me some advice? Is it possible for the engine to work even without a computer? I need it to keep spinning at 20 rpm. It is possible?

[@klincgleda7268]

probably yes if you have an arduino battery.

[@firstindianremotecameratro5123]

How can we control the stepper motor using RC remote

[@frankbonsignore.RochesterNY]

Help! My setup only runs clockwise and doesn't reverse! Everything is just as you wrote it, Paul. Also, I can run mine without the power supply.

[@sodapunpunnarai2336]

same as mine

[@jasmines.6325]

How to do 90 degrees?

[@peterbenbow3932]

please just add a link for the code It never works just showing us it'

[@waels6232]

Doesn't the starting current affect the arduino power pin connected to the driver?? It should not tolerate more than 20mA

[@aparnachavan8501]

I tried with this but my stepper motor doesn't work , one more thing do I need to use the way you have used some pin on it

[@volvo336]

Thank you🙂

[@EnjoyMechatronics]

No problem

[@sharanamuram2290]

what to do if need the motor to rotate in constant rpm ?

[@rotemgiat217]

how to move it faster? Its a bit slow

[@TheWhicobShow]

Great job

[@user-hn2fz1ji2p]

Hi, Love your video... I'm very new about this kind of programming... I have a question: is necessary to connect the ground and the 5v between Arduino and the driver?

[@EnjoyMechatronics]

Yes, absolutely

[@hudan9549]

could you give me the code?

[@__boudi__]

is it possible to control the motor without the driver?

[@EnjoyMechatronics]

No

[@Samanthahr]

great video

[@EnjoyMechatronics]

Thanks!

[@chellalialhcen]

Hello dear bro, i followed this video step by step but when i send the code to my board, the board disconnect from the PC. notice that i have "Az-Delivery ESP32 Wroom" . i thought that the Stepper motor absorbs the energy. to solve this problem i brought an external enrgy source (Breadboard Power Supply), finally worked well but, i got the same problem that "Rajat parkkal" got, the motor don't rotate to the other way i mean the negative orientation. i'll be thankful to help us solving this problem. *Notice: i'm fresh in Arduino and i have no idea befor this is my first steps on this world.

[@J_Creative]

You need a separate supply for stepper motor your facing that problem due to current limitation

[@ForYourConsideration]

Very nice! Thank you for creating such a helpful video. Your explanations were very clear for a beginner like me.

[@EnjoyMechatronics]

Thanks for your interest, and I hope you are doing well.

[@tonkofonko]

Thx it works.

[@EnjoyMechatronics]

No problem

[@Rajatparakkal]

when i put a negative number the motor is not turning the opposite direction whereas going in the same clockwise direction towards the angle. Is there a solution??

[@kenneth4575]

why does INT 1 and INT 2 stay on after the first command and only turn on after a reset?

[@souravbiswas7308]

Can I change the rotation of the motor manually??

[@EnjoyMechatronics]

Yeah you could control it using push-buttons, potentiometer, or joystick 🕹....

[@malikthetalentmaker6001]

استاذ شاكر هي الحاجات دي بتتجاب منين؟؟

[@EnjoyMechatronics]

ممكن من موقع amazon بالنسبة لنا في تونس هناك متاجر تسوق لها أو من خلال مواقع بيع موجودة في تونس.

[@Rishi20051]

Plss can to tell me why the order is 8,10,9,11

[@cbaumanncb]

Same question - in the arduino tutorials it shows defining the pins in numerical order - 1,2,3,4 while you are using 1,3,2,4 Can you explain the difference? Did the stepper library change?

[@nilugajjar182]

Sir please make a more video one motor 180 degree rotation after stop after number 2nd motor run 3 round after stop after 3rd rotation 4 pound after 1st motor rotation reverse 180 degree

[@joochiunglee351]

can u teach how to do stepper motor analog rpm gauge diagram and thank you

[@queen_501_7]

ممكن تعطيني الكود لان كل ما اكتبه يطلع غلط انا سويت نفسك بالضبط

[@Mechanic2341]

Your Gode erro from myStepper ! Tell me please

[@samirdatta5425]

It doesn't work

[@samirdatta5425]

'mySteper' was not declared in this scope When I compling

[@samirdatta5425]

What I make mistakes

[@SussypizzaYT]

THANKS SO MUCH

[@EnjoyMechatronics]

No problem