Two things: If the pump is rated to run at/on 50Hz, the reciprocating assembly should be engineered to resonate at 50Hz under rated load. If you give it 60Hz, you're starting to push the swing before it's returned as far as it can. Second, you should be able to get higher voltages out of that variAC by using it backwards - swap the input and output. Just make sure you start with it cranked to what would normally be all the way up (primary:secondary windings are 1:1). As you turn it "down" you'll be reducing the number of primary windings (the bottom half of the fraction) with a fixed number of secondary windings (the top half). That'll boost the voltage rather than reduce it. At the "bottom" end, you'll be flying off into the cosmos voltage-wise. The insulation and air gap on the windings won't necessarily handle anything over ~130V, so it'll eventually start arcing internally and turn into a Photonicinduction episode.
@pierrelaboom4026 Жыл бұрын
Ooo! Photo induction episodes! Lets do it!
@howlingwolven Жыл бұрын
Move the primary tap to the middle of the coil.
@starlite5285 жыл бұрын
also know it's European because the brown and blue wires. How do you know which color is the 'hot' ? The brown wire, because that's the color your pants will turn when it shocks you.
@antilogism5 жыл бұрын
@Damian Davis That works. I once remembered it by associating brown with the color of dirt on my grave & the blue sky seen while I'm not in that grave.
@thebaconsonful4 жыл бұрын
I was taught, the sky is blue, neutral is blue, because something about the sky. I dunno why. We use red and black here, but accept euro standards so are taught a lot of them.
@GGoffroad24 жыл бұрын
They're both hot on 220v. It's two hots and a ground
@starlite5284 жыл бұрын
Average_azn in the US, yes, but not in Europe
@chrisrage58364 жыл бұрын
We always remember "you don't want to be black and blue" when you wire euro colors to American. Brown/black, blue/white
@danieln90446 жыл бұрын
I think you get the world record for fastest unboxing of an already unboxed box using a chainsaw.
@k1zmt6 жыл бұрын
I think Ave needs a really big box so he can use an old school gas chainsaw to tear apart the box.
@mattjohns33946 жыл бұрын
Daniel Nelson Now it's even more opened
@joeb.50206 жыл бұрын
I say a few sticks of dynamite. Maybe 3 for good measure.
@Drewworksco.51506 жыл бұрын
Gotta keep up apperances.. But you gotta give respect. No one out there has the character No. 1 but also his indepth perspective on how thing's work. Last and most obvious is the fact he has a thousand things goin on at one time.... Anyone can be pardon to that. Unless you wanna nock a guy for one little thing. God forbid the fact we're human.
@BirdmanHT073 жыл бұрын
I will never forget that
@NoelBarlau6 жыл бұрын
If there's any way you could do a teardown of an antique refrigerator to see why they seem to last forever, I'd love to see that. My parents have a 1949 still in operation, but I seem to be replacing ours on an average of every 12 years or so.
@adamhorn8414 Жыл бұрын
Planned obsolescence at its finest. There is no reason we could not build refrigerators like that anymore. And it will only get worse with smart fridges that connect to the internet. At that point the manufacturer can press a button to brick your fridge and make you get a new one
@williamward2948 Жыл бұрын
What 'bobo' said... The copper lines are thicker/stronger. They used r-12, not r-410 or butane. The windings in the compressor motors were of larger gauge wire for more amperage capacity/higher hp to combat head pressure lock up and frying the motor. And also, a lack of a thermal fuse prevented it from shutting down for good when it did eventually overheat. We got an old commercial GE beer cooler that fires up and rattles like a diesel, and has been running strong and keepingthe beer cold for 50 something years...
@user-super-user Жыл бұрын
the compressor's are just built a lot better, for example ive always liked flyght pumps as they seem very reliable some other shite brands wont last more than 2-3 years yet a flyght can can 10-20+ without servicing
@bruiseandy Жыл бұрын
@@williamward2948 a lot of modern fridges run 600 blends which are the same you’ll find in the old school fridges.
@hargrave961 Жыл бұрын
Build of materials. The last compressor I cut open had a broken connecting rod. No bearings, just metal on metal. And, shitty metal at that. Injection molded horse shit. To go along with higher temps, compression ratios and rpms. But hey, it's "more efficient"
@RinoaL6 жыл бұрын
So basically its a drawn reciprocating dingle-arm with sinusoidal repleneration, mounted to a baseplate of pre-framulated amulite?
@arduinoversusevil20256 жыл бұрын
Exactly!
@sferrin26 жыл бұрын
You forgot to run that through the turboencabulator for extra boost.
@rayakoth6 жыл бұрын
Google? Google! I need help with this one.
@jays34386 жыл бұрын
you've been studying...
@vistadrummer096 жыл бұрын
You mistakenly said baseplate instead of basal platen but otherwise spot on
@skunkjobb6 жыл бұрын
You are not using the correct word. It's not a spring, it's a springamathing.
@LilCletus6 жыл бұрын
Stfu
@lazyh-online48395 жыл бұрын
@@LilCletus hi, you must be new to this channel.
@Texaca5 жыл бұрын
no, for less technical people, it's a Doohickey, or a Thingamajig, or a Whatchamacallit, or for Industrial people a Turboencabulator or Turbo-encabulator 😆
@thebaconsonful4 жыл бұрын
@@Texaca my mum uses "hoosiewhatsits" for the TV remote. To this day I still love it.
@horscategorie4 жыл бұрын
It makes it chooch!
@spikeydapikey14836 жыл бұрын
Dang it, now ya have to clean the shop, as you made a clean spot!!
@martinxXsuto6 жыл бұрын
just put some chips there before someone (you) notices
@Inimbrium6 жыл бұрын
Reciprocating linear compressors are also used on laser engravers inside the laser nozzle to keeps positive pressure that keep fumes and smoke out and thus the main focus lens remains clean. It also helps clear the ash away from cuts and engraving so the laser has a clear path to the material so it can go deeper. Especially useful for wood.
@mattbrown48956 жыл бұрын
These make great pond aerators, and are also used in septic tanks (frequently interchangeable terms in my experience). Much quieter when enclosed in a housing. I've seen a small one of these (60L/min) run continuously for nearly a decade. I replaced the filter once or twice, and brushed the bugs and webs out of it annually. Quite reliable. IMO, way better than similar diaphragm pumps.
@TheACEJester6 жыл бұрын
Simple, robust design and engineering, doesn't get much more satisfying than that. Heck, it's not something I would likely ever need, but I gotta appreciate how well it's made. Thanks for sharing!
@ToTheTopCrane6 жыл бұрын
Just a linear motor. Not all that different from a speaker.
@listerdave12406 жыл бұрын
The air pumps used in aquariums (aquaria?) are just like that except for having a diaphragm instead of a piston. There are also cheap spray guns using that exact same principle except that the piston pushes the paint directly rather than moving the paint with compressed air.
@Deftonesdsm6 жыл бұрын
Same way your power brakes work on a car. Vacuum powered linear motor basically(unless you got a hydroboost in a truck). Or i guess an actuator but same idea
@Iceberg863006 жыл бұрын
@@listerdave1240 airbrush compressors as well IIRC.
@kefeer1236 жыл бұрын
My dinky chinese aquarium pump is a centrifugal one. Also moving paint with a piston is a recipe for getting this piston glued right down stuck. Are you sure they are not using venturi like everybody else who want to spray things?
@burtosis6 жыл бұрын
So what you are saying is we are one small step away from blowing people away with music.
@Raytard1246 жыл бұрын
I literally own this pump. I use it for water reservoir aeration in a smaller Hydroponic set up. Pump runs for around four months at a time for a couple years now......thing is a champ.
@benson4u2155 жыл бұрын
@Yuck Foutube four months is about the time for automatic flowering... sativas take almost four months just to fully flower and be ready to dry
@horscategorie4 жыл бұрын
I own a similar pump - runs year round outside keeping my Koi pond aerated. Three years on this pump... Still going strong...
@Majromax6 жыл бұрын
With a rotary motion, you can always attach a gearbox to exchange rpm for torque. For a linear motor, you can't use that mechanical advantage and have to work electrically. High torque/pressure would require high current, since in an inductor/coil the EMF is proportional to current. But with a high current, your electrical losses would also skyrocket -- losing whatever efficiency advantage you may have had to begin with.
@xenaguy015 жыл бұрын
Precisely!
@engineerpauly7480 Жыл бұрын
Correctamundo! Ayyyy 👍👍👍
@drwombat Жыл бұрын
Why does high current translate into greater electrical losses? Is this a fundamental of electricity?
@kylethompson1379 Жыл бұрын
@@drwombat Check out Ohms Law and Joule's Heating Formula. Very basically, losses scale with the square of current. So increasing current through a resistive element will rapidly increase losses.
@ethanpoole34436 жыл бұрын
Those final seconds of video were absolutely heartwarming. So your cat or the neighborhood cat? Our prior neighbors had a cat that would often climb in our vehicles or follow us into the house just out of pure curiosity - just to check things out - and a minute or two later would mosey on out having satisfied curiosity. After locking him in one of our vehicles overnight (thank goodness not during a summer day) we had to always double-check that there was no cat locked in our vehicle after bringing in groceries (or any other reason why the vehicle would be left open for a bit) as he was a sweet cat that we would have hated to see any harm come to.
@Pocahonkers6 жыл бұрын
Now I finally know why my fridge is so proud about its linear compressor. So proud in fact that it says linear compressor about 5 times on the thing.
@TheDutchSoupPissingCompany6 жыл бұрын
At least we now know they do the higher pressures also!
@loddude57066 жыл бұрын
Don't believe it man, it's just a line.
@fitzmorrispr6 жыл бұрын
Sortof a funny thing to be proud of, considering that there's been some linear compressor fridges since at least the 70s. My '73 motorhome has an original "dual voltage" Norcold fridge with a "swingmotor" compressor, which is just one of these in a can. It's dual voltage because it has an inverter built in to the base for 12 volt operation, which is louder than the compressor is.
@jammin60psd6 жыл бұрын
Must be an LG.
@JasonSimpson19666 жыл бұрын
Patrick Fitzmorris: All you really need to do then is harness the vibration of that transformer in the inverter and you can double your compressor efficiency when running at 12 volts.
@trenthollifield6969 Жыл бұрын
This man is the only KZbin channel that I never skip forward and he'll I rewind it more then anything
@listerdave12406 жыл бұрын
AFAIK those things are designed to mechanically resonate at the line frequency so it was probably suffering a little being driven at 60Hz instead of 50. It will probably push a lot more air if you run it at 50Hz, maybe with a VFD.
@Karjis6 жыл бұрын
It is just a coil, handles switching frequency just fine, so maybe vfd.
@BigIggy6 жыл бұрын
Box is open. Still cuts box. You sir, are my spirit animal. ...Thick PP lol
@1n5ane16 жыл бұрын
it's pretty simple why linear compressors aren't used, mechanical force multiplication is simpler and cheaper. Consider something like a a tire inflator compressor with (for argument sake) a piston surface area of 1 square inch. To get up to 90PSI, you'd require over 90lb of force to move the piston in the compression stroke. A linear motor coil that could do that would require an insane amount of current and very thick windings. However, this is very easy to achieve with simple gear reduction and crank mechanism (what you find in typical compressors) and would allow the use of a smaller motor.
@paulbillings17916 жыл бұрын
Note all the moving parts you just described. Different beast for a different purpose.
@Jasoninee6 жыл бұрын
The same thing can be done with the pressure and piston. Notice how you randomly decided it has to be 1 inch? It can just be made smaller and there you go, more pressure. Literally exact same concept of mechanical advantage. Force vs speed.
@1n5ane16 жыл бұрын
@paul billings - I was merely responding to AVE's question as to why they're not more commonly used. Fewer moving parts, sure; but consider how most compressors fail, it's usually in in the piston to bore seal or reed valves. It is very unusual for the gear reduction or crank mechanism to fail. A linear motor compressor still has piston seal and reed valve.
@Jasoninee6 жыл бұрын
@@1n5ane1 I know. I was merely responding to what you stated. It is not hard to multiply/divide force with pressure of pistons as you claim it is.
@1n5ane16 жыл бұрын
@Jasoninee - The size of piston I was referencing was more in line with a typical tire inflator compressor. You could absolutely decrease piston surface area to decrease the amount of force required. Say you used an absurdly small piston with a 0.1 square inches of surface area, you'd still require solenoid that is capable of applying 9lb of force (to reach 90psi). This would still require a fairly substantial solenoid, try looking up the current specs of a solenoid that can do this if you don't believe me. Another consideration is controlling the speed of the piston as you'd end up having to run the piston 10 times faster in order to match the performance of a larger piston; this is very difficult to achieve with if powered off 50/60hz mains, you would likely need a fairly complex inverter. When it's all said and done, it's pretty clear these are non-trivial requirements. I'm not saying that this style of compressor is useless, just pointing out the limitations and reasons this style of compressor isn't more widely used.
@mustie16 жыл бұрын
fish tank pump
@Leib336 жыл бұрын
I was just wondering the same thing. Seems like it would be an adequate pump for an under gravel filter for a tank in the 50 - 100 gal range.
@gregross72905 жыл бұрын
@IntegraGSR54 жыл бұрын
Mind me asking what brand of the pump are you using?
@McGrathBk4 жыл бұрын
Thought the exact same thing
@legendfpv4 жыл бұрын
@@IntegraGSR5 Nitto Kohki
@crazyguy321006 жыл бұрын
Looks like the new camera needs frame/focus training. I'll get the newspaper.
@Banryu956 жыл бұрын
As SOON as you turned that on, I recognized the sound. That's the sound of my sickly childhood, hooked up to a nebulizer breathing treatment for my asthma. I still keep one in case of emergemcies. I always wondered why it sounded so unique, being basically just an air pump. Now I know.
@noanoxan6 жыл бұрын
That's a fancy aquarium pump if I've ever seen one.
@TreyCook216 жыл бұрын
That's what I thought. That's what fer blowin berbles in your tank.
@Obsidian0Knight6 жыл бұрын
The reason this isnt used when higher volumes of air are required is 100% a scaling thing. Remember in the one you just opened up the stroke on that puppy is most likely less than an inch. The issue with solenoids in general is its hard to have a long stroke and a quick reciprocation. This is because as you make your coil more and more massive to accommodate the larger stroke you then end up with issues of dwell inside the coil.
@richarddale766 жыл бұрын
On the note of cooling compressed gas, in the fire service we charge our BA cylinders once, allow them to cool over the space of an hour (carbon cylinders aren’t great insulators) then charge them again to get the tanks as full as possible. Gives you about an extra 5mins wear time
@bigpapa9856 жыл бұрын
Used the word skookum in a college paper... professor said its what pushed me to an A because I showed him your videos!
@drasiritzbir6 жыл бұрын
Awesome, i hope it was skookum as frig though...
@johnsalmons92225 жыл бұрын
Where are you from Trevor?
@bigpapa9855 жыл бұрын
Illinois in the USA@@johnsalmons9222
@johnsalmons92225 жыл бұрын
@@bigpapa985 Had a feeling there was some septicemia going there!! I'm UK....where grades are given on your ability.
@anotheridiotwind12015 жыл бұрын
@@johnsalmons9222 I'm here in the US, where creative explification of the driest matters can be the difference between reaching your audience and getting shelved. It's a talent and ability that should be admired, encouraged, and rewarded!
@arcadeuk6 жыл бұрын
Never Oil, now that's a brand I've never heard of....... Is it like Never Sneeze? ;) Edit: I've just been down to the local Autozone and they have it on the same shelf as the headlight fluid
@iaiafefe61066 жыл бұрын
@IamTranslation water cooled high performance headlights capable of frying your retinas at 1km are the future
@zvpunry19716 жыл бұрын
IamTranslation: Yes! ;)
@cokcicle6 жыл бұрын
@@BlackEpyon you make volkswegan owners very weery. They thought ALL diesel was clean ! Lol
@raspucin706 жыл бұрын
Same shelf as exhaust bearings, just below the windshield modulators
@brokenacoustic6 жыл бұрын
And for frogs snacks, dont ever mix up your headlight fluid with your blinker fluid...trust me...
@wallaceadriandalessio26506 жыл бұрын
Ending it with a small trusting voice asking " Where are you going Papa ? " diabolical.
@kngofbng6 жыл бұрын
You could send your resume to Hollywood what with the cliffhangers. Supporting actress and all.
@vyvianalcott16816 жыл бұрын
He's just going out for a pack of smokes. Nothing to worry about.
@renny_alt6 жыл бұрын
:'-(
@PV2Omni6 жыл бұрын
Engel fridge/freezer uses a similar type, and are fantastically efficient! It uses a Sawafuji Swing motor.
@MaximusPsychosis6 жыл бұрын
So its just an industrial grade fish tank air-pump... actually, i need one of these for my acid processing.. Well, ebay has them going cheaper then regular aquarium pumps..
@LobsterHunter56 жыл бұрын
After watching this video, and reading this comment, what do I do? I go take apart my fish tank bubbler of course... Sure enough, a type of linear motor acting on a sort of bellows to pump air. 1 moving part. Awesome.
@ThePentosin6 жыл бұрын
I need one. Do you have any links to some decent priced ones of fleabay?
@SpecialAgentJamesAki6 жыл бұрын
“My typical maintenance scheme!” I’m dead. It’s all over for me. That was too funny 😂
@whatevernamegoeshere36446 жыл бұрын
9:59 That is some solid current rush, look at that cable twitch!
@chaytonruijsenaars39716 жыл бұрын
i wonder how long that has been sitting on the shelf in the new old stock warehouse, its always cool to see new old stock, when somethings 35 years old but still brand new, the aluminum is all pristeen shiny but the bromine in the plastic has turned yellow over the years and the rubber has dried out in any o rings or whatever, its just cool to have that kind of stuff in your hand, like an unused fire extinguisher that has a tag that says "last serviced: 1971", or your grandpas 7 channel royce cb radio with the wood laminate paint and a date of manufacture that makes you wish you could walk into a factory in those days and see the pride in the faces of the people making good products that were made to stand on their own merits for years to come
@olivierdamiron72793 жыл бұрын
A lot of modern fridges use linear compressors now, so they are suitable for high pressure refrigeration applications too. Like you said, economy of scale, it is just a matter of appliance manufacturers making the switch away from the old rotary ones. LG seems to have gone linear on all their fridges. It's super quiet too.
@94Gidge Жыл бұрын
Engel portable/car fridges have been using them since 1962. Because they are more efficient and reliable.
@gregq3474 Жыл бұрын
My LG went through 2 within 3 years and both techs cursed that design saying how they were constantly failing.
@nitschke30 Жыл бұрын
The current linear compressors in refrigerators you find on the market today are garbage. They are undersized to meet efficiency standards and end up dying. I worked as a refrigeration technician and a good 1/3 of all the refrigerators we fixed were practically brand new but had issues with their linear compressors and or 3 way valves for the dual evaporators.
@darylcheshire1618 Жыл бұрын
I had an LG for 2-3 and still going well. It is a smaller fridge for one person and it is an upside-down fridge with the freezer on the bottom part.
@peteryeung111 Жыл бұрын
I have one of these running in my fishing room for over 16 years, non stop, an still going strong. I got it pre-owned. These Japanese air pumps are legendary.
@StopChangingUsernamesYouTube6 жыл бұрын
Protip: A 240v inverter is perfect for giving these little euro whatsadoodles the what-for. Just feed 'em a battery or the business end of a bench PSU and they'll whirr.
@Burks21215 жыл бұрын
Also works amazing for powering many, many aquariums with air stone filters.
@killak240sx3 жыл бұрын
I came to the comments looking for verification of this very thing. Thanks.
@josvandiepen34253 жыл бұрын
That is exactly where they are used for. Its not a compressor but a air-pump.
@SueBobChicVid6 жыл бұрын
Could probably bolt that to a hopper and use it as a vibrator, whilst directing the discharge air to keep a chute clear. Multi-tasker!
@TheDutchSoupPissingCompany6 жыл бұрын
Sounds like a good plan
@John-wk2fd6 жыл бұрын
Just pull the rubber damper off and you should be good to go
@larrymilsap51235 жыл бұрын
That little girl loves you so much! You're the best, AvE. Love your vids!
@michaelpiotrowicz61006 жыл бұрын
Reminiscent of a fish tank air pump in many ways.
@jimcoleman526 жыл бұрын
I was going to say looks like an oversized aquarium air pump.
@loddude57066 жыл бұрын
Make your Puffer fish bounce with health - buy a bigger pump . . .
@tomtom23466 жыл бұрын
we use them for large fish rooms www.jehmco.com/html/central_air_pumps.html
@JasonSimpson19666 жыл бұрын
Actually, I'm kinda surprised AvE didn't mention that specific use case in his list of many examples. Plus he could have done a side-by-side teardown comparison and see which one actually chooches better.
@markk69576 жыл бұрын
I bet you could use it for a fish tank air pump or even a pond pump
@power-max6 жыл бұрын
This reminds me of the design of the old fish tank pumps I took apart years ago. They used a magnet and a electromagnet to and a "bellow" of sorts.
@electronicsNmore6 жыл бұрын
Nice teardown.
@tassiehandyman30906 жыл бұрын
I work in a nursing home, and we use air filled mattresses for the management of pressure injuries in bed-ridden residents. Got me a sneaking suspicion the pump units use linear compressors... Low pressure, moderate flow, low power consumption, reliable as all get fucked. I learned something today. Thank you. My best wishes to the good people of Darkest Canuckistan... 👍🇨🇦🇦🇺
@aicMadSeason2 жыл бұрын
Hey! I work for a company that manufactures and services those mattresses. I work for HillRom. How awesome it is to run into other like minded people in the healthcare field. And we definitely do use linear compressors to regulate the pressure zones.
@larrymunday75196 жыл бұрын
Was that a banana hammock on the back of the seat at the end?
@arduinoversusevil20256 жыл бұрын
You've a keen eye for that sort of thing eh.
@douglasscott56236 жыл бұрын
I can't believe I went back and looked. I did because, well, with AvE ya just never know...
@user-rb7kg7uk4w6 жыл бұрын
i actually purchased a custom, hand made, banana hammock for my truck from etsy. i decided to upgrade after a road trip where the kids only ate a couple of the mandarin oranges that we brought. i figure that if it's in their eye line they'll eat it.
@george-broughton Жыл бұрын
0:10 i love your no bullshit unboxings. This gets me every time.
@stalkinghawk92446 жыл бұрын
Hey Ave, a reason why they wouldn´t use massive coils instead of motors might be because of big chunks of metal that need to be magnetized. It takes longer to magnetize them thus higher frequencies cant be used, besides having massive magnets disturbs anything around them (electromagnetic interference).
@Soup_or_Stu3 жыл бұрын
I use one of these for aeration of my batches of compost tea for the garden. These little beauties blow some fantastic bubbles.
@toddkrein5 жыл бұрын
About the mold colony in that coffee cup... I'm waiting for the vjo on extreme biology.
@michaelmclester69215 жыл бұрын
Linear compressors are used in residential anarobic sewer systems, they run non stop for years, just needs filter service regularly. Not a cheap compressor but very reliable.
@benjamindyer73486 жыл бұрын
I have asthma and occasionally use a machine called a nebulizer, I've always wondered how that little thing compressed its air.. I knew a crankshaft and Piston style would be to much for it. this is most likely what is used, learned something new! possibly.... I'll have to Google it to be sure
@MisterCheemf3 жыл бұрын
It depends on the model. I've torn apart an old one to fix it and it does indeed use the crank and piston.
@Ankyl-Osaur Жыл бұрын
Chickadee was real sweetheart back then. Love the cat at the end. Be great to see more of that guy!
@clencheastwood15716 жыл бұрын
Kind of random thought I had watching this, but you always rag on cheap manufactures taking shortcuts or using cheaper parts/materials to save a buck. When, truth is, there's an engineer out there who figured out how to make the tool work as intended while cutting the cost, which while crappy for the end user, is still impressive in it's own right. So, I had a question for you about this. What's some of the most impressive 'cost cutting' measures you've seen in a tool and what are some of the most pointless. Maybe this could make a video one day. Anyways, that's my random tangent. Thanks! As always, love the vids, keep them coming.
@caodesignworks24076 жыл бұрын
I think part of the problem isn't that some engineer made it work as intended, because that's not the hard part. The hard part is making it work as intended while still being robust enough to actually last through a normal job. You could argue that was the intent, but I'd like to think the intent was to make a working tool. And if a tool stops working, it's lost it's intent.
@paulbillings17916 жыл бұрын
First,you start with sound dampening foam that turns to schmoo.
@aicMadSeason2 жыл бұрын
But the manufacturer creates the budget for the engineer. Leaving the engineer to substitute a metal part for a plastic part. Does the plastic part function as designed? Yes, but it’s life is 10x shorter. I also believe the engineer balances a fine line between creating parts that work amazing and creating parts that break, therefore driving revenue through repair. Not a fact, just an unprovable thought.
@simonshaw51194 жыл бұрын
You See these a lot for people who Keep ponds and aquariums, using them with air tube and an air stone to push air into the water allowing for water movement and it also disrupts the waters surface allowing a better oxygen exchange transfer at the surface. Decent little air pumps having used one for a long time; although I’ve never taken it apart so I appreciate the video. Thanks 👍
@johnt18156 жыл бұрын
I suspect having a hefty bit of rotating mass to keep it turning "smoothly" is quite helpful for a reciprocating system that needs to supply any kind of pressure. You have some inertia to help on the pressure stroke, while the motor can continue to make up for the used energy on the intake stroke, thereby smoothing out your power draw a little. Also, a little mechanical advantage from the crank configuration?
@InXLsisDeo6 жыл бұрын
Also vibrations
@wernerhiemer4064 жыл бұрын
@@InXLsisDeo No vibrations so this old in and out is in need.
@raidkoast Жыл бұрын
This is a very complicated way of making a fan. I like it.
@seansysig6 жыл бұрын
To get say 120psi @12cfm the size of the linear compressor would be like a 18 cubic foot freezer!
@laserflexr63216 жыл бұрын
Being as you chose the word "like" I am led to believe that the figure you state is an approximation. Ok, but that begs the question; is that an approximation based upon relevant knowledge and working experience with linear compressors or at least in substantially equivalent arts, or are you just plucking that from your posterior? While awaiting the results of your curriculum vitae to asses the merit of your claim, I took the liberty to research freezers and discovered there is quite a range of external dimensions amongst the various freezer models listed as 18 cubic foot capacity. Now for most applications a ballpark figure would be acceptable but as I am planning an extended-stay, extra-planetary excursion, I need the datasheet for my pescine growth media dissolved gas control unit to be a little more precise. Can you point me to a specific compressor model or at least the freezer you had in mind? Oh forget it, the high altitude project just got cancelled, gotta take the trash out or no squeaky squeaky tonight.
@DavidBcc6 жыл бұрын
L m f a o.
@brian_sipe6 жыл бұрын
Imagine writing a damned book as a reply to someone's off-hand comment.
@josephdanmathis18764 жыл бұрын
You have a killer shop, packed with Wicked gear. I'd like to have that situation in my shop, but those are just things. When I hear that sweet little voice say "where are you going Papa", I get feels I thought were lost with childhood. You got it made big guy. A little perspective will keep a smile on that smart mouth. Thanks for sharing. Love and jealousy, Dan ; )
@sportbikeguy98755 жыл бұрын
typical maintenance scheme "never oil" haha, yesterday i was enlightened by your channel, now i cant stop watching because of the commentary haha
@jasonpressler71116 жыл бұрын
it warms my heart that you make coffee correctly.
@treschlet6 жыл бұрын
It's basically a speaker driver! Hook it up to a power amplifier :D
@StevenWillmy5 жыл бұрын
a power amplifier that kicks out 250 volts?! It'll need a step-up transformer =P
@kostassarakinos30626 жыл бұрын
I don’t understand why nobody invented this many years ago it’s so simple!!! Really cool btw !!
@JuxtaposedStars6 жыл бұрын
I think they are limited in the volume of air they can move by their basic design. If the cycle of the pump is tied directly to the hertz cycle, you have a maximum output speed. With belt driven compressors, you have the gearing advantage to get more compression "cycles" per hertz by just installing a larger motor and/or different pulley ratios.
@domaves40434 жыл бұрын
Got something very similar for the pond air stones. Got socking wet once, dried it out. Runs like a champ, 24/7/365.
@rollymaster166 жыл бұрын
AvE: "We're not changing one to the other to the other" me: adapter stack!
@edwinrots11346 жыл бұрын
I picked one of these out of a coffee machine - the compact ones for liquids are pretty fascinating - complete physical separation of the piston from the solenoids. I suspect these only work for low pressure applications because they can't deliver the power a mechanically linked prime mover can deliver.
@CeeKayz0rz6 жыл бұрын
>Box was already open on top >Chainsawed it open anyway I f'ing love this channel!
@vdubjunkie6 жыл бұрын
When your little girl (yours?) said "Where are you going papa" it was about the cutest thing I've heard in one of your videos!
@teardowndan53646 жыл бұрын
Good luck getting 130+psi and a decent refill rate on a linear compressor, especially if you have only a 115V 15A circuit to work with - you'll need a lot of peak power to get the piston to bottom out and force every bit of compressed air out for maximum efficiency. With a rotating motor, you have the motor and pulley/gear momentum smoothing out those peaks.
@Ratlins95 жыл бұрын
Thanks AvE, on the door of my LG refrigerator is an inscription that reads “ Linear compression .” Now I know what the hell they are talking about. Excellent video.
@l.george75174 жыл бұрын
Ken, I hope you LG is still running. They ran the liquid refrigeration line thru ghe condensation tray to help cool. However the alkaline condensate eats thru the copper. Isolate that line from the water and it will last. Although the parts are warranted for 10 years, the labor is not. $1,800 labor the replace refrigeration system and they will not send you the parts, only a qualified shop.
@iamdarkyoshi6 жыл бұрын
Put the coils in parallel with the diode on the incoming supply and it'll run on 120v
@shurdi36 жыл бұрын
Gonna have to replace the diode for one that's rated at twice the current as well though
@nf4x6 жыл бұрын
Or should at least check the rating on the diode. Given the size, I'd be very surprised if it wasn't just fine for twice the current.
@dandevries71246 жыл бұрын
The two coils could be wired in parallel but they would have to be in series with the diode.
@johnpossum5566 жыл бұрын
mathematically it only takes about 200ma but it looks like they used a 3amp barrel diode just to be on the safe side.
@ramosel6 жыл бұрын
or you could pull the wires off the coil and hook them to a real compressor and actually get something done...
@skokie236 жыл бұрын
My LG refrigerator has a linear compressor. Same animal? Keep the vids coming AVE! GREAT STUFF!!
@kabadisha6 жыл бұрын
My bet would be that linear compressors have a low maximum pressure and cost increases significantly with pressure. Common motor driven compressors won't have the same issues.
@shurdi36 жыл бұрын
The max pressure is essentially dictated by the spring though, since that's what's actually doing all the compressing. Probably gets quite power hungry trying to pull back really heavy springs, so you'll need wires that are much thicker for the coil. That alone will probably cost you more than the electric motor
@MascottDeepfriar6 жыл бұрын
exactly what i was thinking.
@jimandaubz6 жыл бұрын
Ya. Seems like it, you would need to replicate the entire motor for every cylinder too and everything would be overly complicated to get good pressure. But it definitely seems possible, but, then again. For what gains, 2% or less in friction losses? And no ability to use cross platform parts? Thats a lot of cost incress for those last 2%. Not worth it. Ps Did you mean reciprocating with the rotary motor? Because rotary compressors are a whole different animal, really good at high volume and terrible at high pressures, they bend the vanes if you push to much through
@kabadisha6 жыл бұрын
@@jimandaubz I did mean reciprocating with a motor. Didn't even know true rotary compressors were a thing. Learn something new every day!
@jimandaubz6 жыл бұрын
@@kabadisha i figured as much! Haha, they are not common by any means
@Alexbk007 Жыл бұрын
This works the way I thought a single moving part work be crazy, that's cool
@peetiegonzalez18456 жыл бұрын
That's noisier as frig, but reminds me of the piezo pump that BigClive dissected not so long ago. Exactly the same principle except used a piezo-electric speaker as the actuator.
@Omnis26 жыл бұрын
But remembers the pound cake rotted
@ericpaulgoldie6 жыл бұрын
Just arrived and have to say that is the most bad ass way of opening a box, LOVE IT!
@jamesbond98735 жыл бұрын
Always liked when he says molybdenum disulphide! Lol
@dtrrtd7746 жыл бұрын
That looks like it'd make an awesome air pump for an aquarium- oh what bubbles she'd make!
@Marvin.Runyon6 жыл бұрын
It chooches 60 times a second in countries that have put a man on the moon, or at least sent a reusable robot arm to orbit.
@loddude57066 жыл бұрын
If 50 Hertz, 60's gonna really Hert . . .
@BigSmartArmed6 жыл бұрын
"man on the moon" lol!
@Alex-uy7pc6 жыл бұрын
@@BlackEpyon dual purpose space heater
@AKADriver6 жыл бұрын
Now what's really nuts, in its home country it'll chooch at different speeds depending on which side of the Fujigawa river you're on.
@jordandyck47216 жыл бұрын
Gotta love those Canadian arm jobs
@FSstudios16 жыл бұрын
I found one of these in my father’s cold therapy machine after he had surgery. It was pretty cool to play with as the pump itself was all contained in the box/wall wart with the pneumatic tube coming directly out of it.
@ElectraFlarefire6 жыл бұрын
To convert from 240 to 110: Cut the diode between the two after the stripe.. Connect the brown wire to it instead.. Then connect a second blue wire back to the start of the second coil(where the diode connected).. add a second diode and a second brown wire afterwards so you have two N->coil->diode->A in parallel. That should do it.
@jacobmay75946 жыл бұрын
The man himself said there werent no way in helicoils he'd reach a million subscribers but is only a measly 36k gentlemans away. Keeper moving from the great state of Wiscaaansin.
@johnepperson88676 жыл бұрын
"Made in Japan", I sure miss those good old days!
@toadamine Жыл бұрын
So this is how those aquarium pumps work! Thank you.
@TheClampettmobile6 жыл бұрын
I believe some home aquarium pumps run on a similar (but MUCH cheaper) principle.
@noimagination99 Жыл бұрын
I have a cat that looks exactly like that, and he follows me everywhere, and makes sure I'm doing my work right like Ave would do it! 😉
@Allan0036 жыл бұрын
The real question is, where ARE you going Papa?
@Reeceander6 жыл бұрын
seems ominous that he edited it to stop there, no?
@tomwhipp32456 жыл бұрын
@@Reeceander sounded pretty creepy tbh. then again I watched this on Halloween.
@kroonoverdrive5 жыл бұрын
Cement Factory? Dog Food Plant? Hopefully a happy home for pumpkin.
@derBara833 жыл бұрын
Cant provide enough UMPF - Im absolutely blown away by your vocabulary!
@AlBarathur6 жыл бұрын
I love simple and robust machines just like you. But these reciprocating motors have their own limits which is why most higher power applications will use regular circular motors. Ventilation is one of them ( if you think about it any circular motor only needs some blades installed and it got its own fan, now reciprocating motors of higher power output would need external fans, which defeats the point of them being simple and robust since that smaller less reliable external fan is what would keep the bigger internal motor from destroying itself. Another problem is the hysteresis. As you scale up a "back and fourth" type of electrical motor, the sheer weight of the parts make it unable to move at 50/60 Hz speed. Problem the third: You saw for yourself, the heart of that thing is a spring. So underneath that apparent superb reliability, you have machine that is relying on bending a piece of steel back and forth until it breaks. Myself I have imagined solutions for that, but the results I got made a circular motor look simple because my solution needed a kinetic energy accumulator (a fly wheel) like old time steam engines and my back and fourth motor was no longer functioning on 60Hz but it worked on any voltage frequency since my motor was only working as an electromagnet and relied on electronics to switch on and off. The electronics were solid state but they had to be oversized on account of the switching of the coil (you know how coils don't like to be switched off, they do like your wife when you tell her she is talking too much)
@richardgreene68106 жыл бұрын
Isn't it also easier to throttle a rotational electric motor?
@testuser9t8815 жыл бұрын
car valves use springs. There are a lot of these operating at thousands of cycles per second and usually none break
@SaintTrinianz6 жыл бұрын
lol, best unboxing ever... would love to watch this guy on Christmas morning!
@jaredromero51146 жыл бұрын
0:58 "a skookumpressor!"
@Saturn49YT6 жыл бұрын
I seriously want one of those saws just to open things this holiday season. Kids new toys with 10 zip-ties? Bzzzzzzt. Time!
@981porsche36 жыл бұрын
I love that you sawed the open box open. What would be the challenge in just dumping it out? Smart like a fox, you are!
@king4aday4aday6 жыл бұрын
He has to justify having bought TWO miniaturized electric beaver simulators!
@TheDutchSoupPissingCompany6 жыл бұрын
Come on, this is a stylish channel...it has to be stylish
@sundown7986 жыл бұрын
Replaced one of these for the dryer cycle in a dental autoclave. One coil had failed due to the intake being inside the case that caused it to fail due to years of moisture. They eventually fixed the problem with the intake outside of the unit with a dust filter. Cool you posted this little breeze of a fart machine lol.
@thedavesofourlives18 ай бұрын
See LG fridge compressor lawsuit due to linear design compressor seals failing.
@colinsmith63406 жыл бұрын
Due to the sealed unit, you could hook them up in series and get a pretty large pressure boost.
@butth0le_inspector6 жыл бұрын
"Genius" - what else you could expect from the Japanese?
@grumpysteelman4 жыл бұрын
Wasabi
@Chris_Bumpus6 жыл бұрын
Love these pumps. Have one running on my large fishtanks all the time.