Armscor M200 Cal.38 SPL Disassembly & Assembly & Parts Identification

(DISCLAIMER: No copyright infringement intended.
I do not own the audio in this video. They belong to their rightful owners.)

[@FIGHTER-n8x]

Salamat boss sa wakas may naglabas din ng video kung pano tanggalin yang ejector nayan kahit mga taga ibang bansa Hindi nila Alam pano tanggalin yan

[@leonardpiskacsr.7111]

Much hand fitting ...not as cheap as people think...Thank you for this!😀❤

[@thefleaflop]

Hi,... nice job... you make it look so easy!.... Can you tell me what the Trigger spring "Spacer spring" is for??? It does not seem to compress or relax at all during the trigger pull. It seems to act like a bushing to space the trigger spring off the back wall of the frame. Do you agree?

[@Kamoflage7]

During reassembly, everything works well until I attempt to reinsert the crane lock screw, detent, and spring. I line them up (though the detent does not want to fit well into the screw) and screw them in. I get resistance before the screw is flush. At that point, the gun functions normally. If I tighten the screw beyond that point, the chamber is too tight and does not want to rotate or release. Any advice? Thanks!

[@MaxArmaments]

check the crane fitting first before inserting the the crane detent, spring & screw, if not working disassemble it again to make sure the Hand and Release button is in place,

[@matthewrobinson4323]

I feel like a real idiot asking this question, but I'm desperate for help. I recently bought a pre-owned, and apparently rarely fired m 200 with beautiful wood grips, to go with my m 206. I think I have really messed up my m 200. I don't even know why I did it, but I loosened the cap on the front of my ejection rod, and the star at the rear of the rod came off. I CAN tighten it fully, but then the holes don't line up with the stars. To get the cylinder holes to align with the stars, the star is only finger tight. Other than that, the gun worked flawlessly at the range, where I put about 100 rounds through it before I messed it up. PLEASE advise me. I've tried tightening the ejector rod cap at the front, but that doesn't seem to address the problem. Thanks in advance.

[@hanylethbarrientos3738]

Boss,ano pong diperensya ng revolber ko?unang putok ok ang tama ng firing pin sa puwet ng bala and the next na kalabit ay di na tumatama sa cylinder ng bala?

[@jessrielhanquin6159]

Thanks a lot lods..👍🏼👍🏼👍🏼

[@ridgelachlan4951]

Instablaster

[@bobgordon6029]

I noticed you took the knob of the ejector rod off so easily...mine is frozen solid and won't budge! Even using pliers...

[@kuyaayi6466]

Idol same lang ng parts sa .38 Rev Armscor M202 po ito? Newbie here.

[@bck83gc]

Where can I get grips like those? Mine came with hard plastic grips?

[@MaxArmaments]

just go to wood craftmen & request to carved it,

[@ranzcator1246]

Sir paano tanggalin yung firing sa 38 revolver?

[@elvisayala2509]

Que origen es armscor 38 modelo 202

[@xamjucal7593]

san ka nka score ng wood grip mu nyan sir??

[@caseyconley9383]

How do you remove the barrel?

[@MaxArmaments]

u can see a Pin Connected to the Frame & Barrel, just punch it. i advised not to remove except if the barrel is damage.

[@cctvicac]

✌️👌✌️☝️👍👍👍 Very nice about each video.

[@golong1343]

Boss, yung ejector po ba loose ba talaga yun or tight dun sa ejector rod para align siya dun sa notch ng cylinder?

[@MaxArmaments]

dapat tight un para hindi gumagalaw na mgfit ung ejector sa cylinder kapag nilalaro mo,

[@MaxArmaments]

turno lng po yan, mahaba naman ung ejector rod,

[@golong1343]

@@MaxArmaments salamat po.

[@golong1343]

Siguro na over tight na yun kasi di na siya uupo dun sa cylinder notch kapag tight talaga; Uupo siya kung loose at pag nagalaw di na ma-isasara ang cylinder.

[@victorbartolome716]

Sir saan ba nabibili un perma blue

[@junenormanobida2430]

ang 22 five senioreta paano po?

[@bongnuguid9024]

Boss pano palambutin ung gatilyo

[@thadeuscamunias6848]

sir... ano po kaya issue nung sakin mayjo may kaunting kalog ang barrel nya

[@MaxArmaments]

kung sa barrel po, pacheck nyo nalng po sa gunsmith, kc baka ung sa cylinder po hindi fit don sa barrel kaya baka palaging natatamaan ng bala po ung barrel kaya ngloloose ung fitting po sa aking pananaw po, mas maganda po sa gun smith para cgurado,

[@renrenmcdal9877]

boss san pwede mkabili ng crane lock spring nyan...tnx

[@georgesolmira4785]

Good day sir san pwede maka bili ng mga part nyan

[@MaxArmaments]

depende yata sa gun store sir, kung kaya ng gunsmith, pagunsmith mo nlng sir kung walang available sir,

[@MaxArmaments]

[e-mail]

[@felixnathanieltuazonpunzal8203]

Good day Po sana Mapansin parin ako sir dikona Po mabalik Ung sakin after ko baklasin Huhuhu

[@MaxArmaments]

message mo po ako sa messenger silver maximo

[@joseromerojr1923]

How much po

[@MaxArmaments]

not for sale sir, just for info sir,

[@renrenmcdal9877]

boss san pwede mkabili ng crane lock spring nyan...tnx

[@MaxArmaments]

pwede man yan sir improvise, hanap ka lng ng kasya jn sa crane lock detent, khit nung sptin na medyo matigas then putulin mo nlng sir,

[@renrenmcdal9877]

pati kc detent boss nwala

[@MaxArmaments]

turno na tlga yan sir, medyo luma na kc, hiram ka ng ganyan na part then paturno mo,

[@jovinvlogs5615]

Mga magkano na kya ganyan ngayon mga sir? Ganyan kase ung naiwan ni lolo pero nakatago balak ko nlang sna ibenta

[@dextertalamera]

​@@MaxArmamentssir no lock sa crane no spring ang screw safe ba gamitin?