DIY Generator | How to make 250W generator

  Рет қаралды 194,600

American Tech

American Tech

Күн бұрын

Пікірлер: 116
@howiewood
@howiewood Жыл бұрын
This is a wonderful example of the concept, and very well demonstrated. But you've undervalued the strength of your Neomags. That magnetic field is shooting out of both faces of your mags, more coils = more juice. Lengthen your shaft,and add pulleys, connecting it to your turbine. ( I'd try a vertically mounted shaft, its simple, and catches wind from any direction. ) Good job!! Keep up the effort. This could used very well as an educational tool for all sorts of folks. Help spread the word, Our ingenuity can solve many,many of our problems, and you're well on your way! MORE POWER TO THE PEOPLE!
@FlexibleBladeTurbine
@FlexibleBladeTurbine Жыл бұрын
A second coil ring would double the output. And: air coils need much more speed, but acrylic glas will not withstand the fly wheel forces. However trying to drive a motor rated 250W without a load doesn't prove anything. Try to put a shunt resistor of say 0.01Ω in series. Then you should measure a voltage drop of around 2.5V @ 250W by using Ohm's law. I am pretty sure your system will produce not more than 0.7V or 70W. But I like your design. It looks so easy and clear.
@chehystpewpur4754
@chehystpewpur4754 10 ай бұрын
what is cool though if it even works at all which i see no extra wires it doesnt take much power to run.
@stels322
@stels322 9 ай бұрын
@@chehystpewpur4754 I'm trying to assemble such a generator and it looks like my hands are not the same as a result, there is no result
@chehystpewpur4754
@chehystpewpur4754 9 ай бұрын
@@stels322 odd response. but i get it. could just be a simple design flaw or oversight keeping your from working
@WildBearFoot
@WildBearFoot 6 ай бұрын
Are your magnets alternated?
@davidwarda5616
@davidwarda5616 11 күн бұрын
yes it would. but if you look at the design of the coil and the pattern, you will be able to see why the voltage of AC is low, like 22V AC. its because its not in the correct design to produce higher AC voltages. coils are meant to be round or square shaped and not the way he designed it. if the coils were designed correctly and in the square or round order or design, the output would be much higher, as long as he used full speed, which he didn't, which did not show the maximum, since he used full speed on the motor and not the meter.
@WildBearFoot
@WildBearFoot 6 ай бұрын
Did we really need to watch him tighten every bolt while also listening to techno?
@anandawijesinghe6298
@anandawijesinghe6298 Жыл бұрын
This design does not exploit the full flux potential of the magnets by not providing flat mild steel return flux back plates. If that was done, the air gap flux linking the serpentine coil would be much greater and would produce substantially more power output. This modification would not introduce cogging torque.
@nobodyelse-k8z
@nobodyelse-k8z Жыл бұрын
That's why all motors use a metallic case?
@bogdank.z
@bogdank.z 10 ай бұрын
From the dynamo you get 1.3A 22V, the fact that the 12V 250W motor works does not mean that the dynamo has a power of 250W. The presented Dynamo/generator has approximately 20W. Show current consumption test.
@BuildingFromScratch
@BuildingFromScratch Жыл бұрын
I like this generator. Can you provide a parts list like the color you used to connect the 2 stators? It would have been nice if you had shown how the magnets are positioned in the stator for thoughts that don't know how to do it. In my case, I do know and would like to let everyone else know. Each magnet is placed alternating the poles. The first hole is North and the next is South then North and so on. One thing to keep in mind is that the poles on the other stator need to be aligned so that the south pole on one disc is alined with the north pole on the other disc. I hope this helps thoughts that were not sure how the magnets are placed.
@Celcius1
@Celcius1 16 күн бұрын
this is not his idea, he just copied iot from another yet to be known youtuber, this guy is a fraud
@expertknowledge5512
@expertknowledge5512 2 жыл бұрын
You are brilliant scientist 👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻
@19hakan72
@19hakan72 Жыл бұрын
coil and magnets should be vice versa (u would have double efficient ;) so, a singel magnet rotor in the middle but 2 of stable coil plates at the out ;)
@Shynook
@Shynook 9 ай бұрын
As some sayed...in short,you can do it better to ghet more energy. Personal thought-The next step for such a generator is to make one worck in vacume(no air=no friction).
@ВиталийОвчаренко-т7й
@ВиталийОвчаренко-т7й 9 ай бұрын
To create a 250W generator using DIY methods, you can consider the following options: 1. Using a lawn mower engine and an alternator: This involves using a lawn mower engine and connecting it to an alternator to charge a battery, which can then power an inverter to generate AC power. 2. Building a series magnetic generator system: This method involves connecting two identical permanent magnet DC generators together to double the generated voltage. This can be done by connecting their shafts together using a shaft coupler or a back-to-back drill chuck system with a pulley in between. 3. Building a miniature gasoline generator: This involves using a small four-stroke gasoline engine, such as a 36cc engine, to power a DC generator. The generator can be used to charge batteries or power appliances using an inverter. Please note that these are general suggestions based on the information provided. It is important to research and follow detailed instructions and safety precautions when working with generators and electrical systems.
@Delta19G
@Delta19G Жыл бұрын
Good concept and execution the add in me kept fast forwarding to the good parts
@Sir-Dexter
@Sir-Dexter 17 күн бұрын
nice work .....good build
@dariotellezh.3530
@dariotellezh.3530 2 жыл бұрын
Algo digno de compartir. excelente trabajo. felicidades
@simsimakov1457
@simsimakov1457 2 жыл бұрын
Особенно интересно тщательное 2 мин. закручивание винтиков.
@azadmaaruf9120
@azadmaaruf9120 4 ай бұрын
And laser blading based on computer designed aided by CNC .... The bulkness of the fast turning coil as the magnet fields strength are playing the leading role, as it is known.
@QUADBOYification
@QUADBOYification 2 жыл бұрын
Good thinking, you could add a second ring with magnets on the otherside reversed poles. Increasing amplitude output.
@electronic7979
@electronic7979 2 жыл бұрын
Excellent project 👍
@howiewood
@howiewood Жыл бұрын
Great idea.A+ for effort ,C- for implementation, sorry, but you are only taking advantage of a small amount of the available force of those expensive neo-mags. The advantage of the axial flux field is that you have wasted half the available energy in the system. You need too wind up at least two(2) more sets of coils for the outer faces of the mags.. Make sure the offset angles compliment the intersection of the mag fields, in order to minimize "mag-lock", and to smooth out rotational resistance. Just an idea.. LITTLE MORE COPPER; LOTS MORE JUICE,.?.
@SC.243k
@SC.243k 2 жыл бұрын
Awesome… very beautiful 👌 Fully watched 👍
@Noneyobusiness851
@Noneyobusiness851 Жыл бұрын
This gives me an idea for building something similar But utilizing differential gear set
@earthlingthings
@earthlingthings Жыл бұрын
You should wind the coil vertically outside the magnets. Which should also be wound vertically. That way you will get more volts. Pretty much 10 times. Because the coil needs to have almost zero 45degree points. In your coil there is a lot. Do it again. As I said. And see.
@davidwarda5616
@davidwarda5616 Ай бұрын
I agree. and the way the magnets are facing is both incorrect and improper. to get the most voltage, like my DIY generator, the magnets must spin inside the coil at the closest range possible, and must spin sideways inside a round coil at the highest speed possible, which is possible using a DC brushed motor of 12 to 24V DC.
@dinosaur0073
@dinosaur0073 Жыл бұрын
Thank you Maaan.....loooove that naked machine...!!!!
@avatarklh
@avatarklh 2 жыл бұрын
every 90 or so seconds was a commercial advertisement making it an aggravating experience. great work on the trinket though.
@marianpanait7926
@marianpanait7926 2 жыл бұрын
Frumos lucrat .intreb ce turatie are si daca opune razistenta si ce aperaj are
@nataliapalweski2072
@nataliapalweski2072 8 ай бұрын
I just watch your videos because you don't say lie like other making 27000 watts 😅. Can you please make some dynamo operating from few watts motor and output 5000 or 10000 watts.
@InventR_
@InventR_ 2 жыл бұрын
Awesome work💙
@dearteddy
@dearteddy 11 ай бұрын
Nice project..👍👍
@davparksoh
@davparksoh 5 ай бұрын
What brand name is your 50W CO2 laser and its cost? And what was the max rpm on the drill powering it?
@Afzalkhan-nb9rk
@Afzalkhan-nb9rk Жыл бұрын
According to you, out of all generators which one is the best?
@oneeight9238
@oneeight9238 Жыл бұрын
Good looking work . Did you try bumping it up by running coil magnets coil magnets coil . 3X the output with the same energy used in the rotation.
@stephentopp1512
@stephentopp1512 2 ай бұрын
I liked the build but the music nt so much
@AugustineAriola
@AugustineAriola 2 жыл бұрын
We enjoy your works from Africa. Please tell us the poles of the magnet: It is likely that the magnets on the same sheet alternates between north pole and south pole and the magnet on opposite sides have different poles (That's, north pole to south pole and vice versa),
@ВсеоПортугалиивключаярыбалку
@ВсеоПортугалиивключаярыбалку Жыл бұрын
Can you please tell me where you bought the bushings. Thank you
@SuperFredAZ
@SuperFredAZ 4 ай бұрын
the title is misleading and I doubt very highly this thing could put out 250W
@garagem100criatividade5
@garagem100criatividade5 2 жыл бұрын
Parabéns pelo seu projeto 👏
@victorapalkow8681
@victorapalkow8681 2 жыл бұрын
COOOOL GOOD WORK SERVICE FIX 🌟🌟🌟🌟🌟💙🤗
@SpaceSoftSystem
@SpaceSoftSystem 7 ай бұрын
Check input RPM and output RPM with voltage
@bennyellis3512
@bennyellis3512 Жыл бұрын
is there a way to build a three phase variant to the mono coil? other than stacking 3 in parallel or resorting to the usual style of alternator which CAN be made to generate 3 phase?
@wullie1320
@wullie1320 Жыл бұрын
I have made a 3 phase axial flux generator with 3 stators and 32 3x1cm N52 magnets. there is plenty of vodeos on youtube but essentially just connect coil 1,4 - 2,5 and 3, 6 together. Use a rectiier and split the one connection to each rectifier.
@dnmnsmith
@dnmnsmith 8 ай бұрын
@@wullie1320but he has one serpentine coil. I too would like to understand how to add a couple more phases to this design, but your answer doesn’t make sense in the context.
@kywildcats6302
@kywildcats6302 2 жыл бұрын
Only thing wrong with this video is the music! Sorry to say
@JeroenvanDruten
@JeroenvanDruten Жыл бұрын
voltage means nothing. amp is important with a little bit of volts
@aadhithvarathan5432
@aadhithvarathan5432 2 жыл бұрын
Next make BLDC Motor with this same generator. Just add 2 more coils in 120 degrees phase and then connect it to an ESC
@rickykbuki2003
@rickykbuki2003 3 ай бұрын
what is the output current DC or AC??
@davidwarda5616
@davidwarda5616 Ай бұрын
its AC power. when you spin the magnets near a coil at close range, you generate AC. but his design did not output that much AC voltage, because the way the magnets are facing is incorrect and outputs far less power than having it spin inside the coil, which in this case its not positioned properly. he also needs to use a DC motor with significant speed, because the drill motors don't have enough speed for significant output. and here is the answer for you, its AC power.
@davidwarda5616
@davidwarda5616 Ай бұрын
sorry, actually this is DC and not AC, because how is the voltage immediately generated after spinning. AC power has a delay in generating, so this is not how you generate AC.
@ggchannel2574
@ggchannel2574 2 жыл бұрын
Alat pemotongan canggih apa itu Mr tolong jawab
@somsakkulchanapakorn95
@somsakkulchanapakorn95 Жыл бұрын
new concept input as before but change the design will get 2 times more output
@devandoB
@devandoB 6 ай бұрын
Muito top
@wingedbull1257
@wingedbull1257 11 күн бұрын
@2:55 what is that he is holding in his hand please????
@angelguerrero2890
@angelguerrero2890 2 жыл бұрын
Can you put a small motor powered by a solar cells to spin the generator
@Rahulchowdhury-mo9rf
@Rahulchowdhury-mo9rf Жыл бұрын
Yes
@BasementEngineer
@BasementEngineer Жыл бұрын
Why would you wish to do this? Think about it!
@FriedPotatoNugget
@FriedPotatoNugget 2 жыл бұрын
I’m going to attach this to a wooden escapement mechanism and build a clockwork computer. I don’t know how long it’ll take, but I’ll let you know.
@sandeepkhelna3488
@sandeepkhelna3488 2 жыл бұрын
Please make a video on axial flux motor
@__NEMO__
@__NEMO__ 4 ай бұрын
Нет бро... Покрутить мотор без полной нагрузки - это совсем не 250W... (
@zusclhz
@zusclhz 2 жыл бұрын
How many volts is being used to generate this 22.5v ?
@jacekhubert100
@jacekhubert100 10 ай бұрын
Impressive!!
@victormanuelcazarezhernand1940
@victormanuelcazarezhernand1940 Жыл бұрын
Sería mejor con una placa de imanes y una placa de bobinas a cada lado, tipo sandwich, produciría el doble de electricidad...
@agustinmiguelperezperez6464
@agustinmiguelperezperez6464 Жыл бұрын
Jajajaja ese voltaje lo lo consigo yo con un motor de batidora de 220v DC y llegó a los 32 voltios con pocas revoluciones, ¿pero como lo mantengo a 250 rpm sin árbol de inercia?
@mjktrash
@mjktrash Ай бұрын
Yeah, I'm calling bullshit. Just because you made a 250w motor move doesn't mean your generator is making 250w! You made ~22v and have wire that looks to be around 20-18awg, so roughly 2amp capacity? Am I wrong on the gauge? If I'm right, you've got something in the neighborhood of 50w output. Spin that much over 3k rpm and make sure you're not standing in the path of those magnets.
@thaidev3153
@thaidev3153 2 жыл бұрын
Can you make low rpm small gennerator
@auditionbacgiang781
@auditionbacgiang781 3 ай бұрын
tại do quấn ít dây đồng quá nên vol thấp
@bilgeboz6038
@bilgeboz6038 Жыл бұрын
adam gözümün önünde bütün vidaları tek tek sıktı
@haraldlauchkorper7109
@haraldlauchkorper7109 2 жыл бұрын
You build the full shitty generators from morning to night.
@programmerpladag4902
@programmerpladag4902 2 жыл бұрын
Copper design really work? It look not work. But i'll try.
@mustafaamjed_14
@mustafaamjed_14 2 жыл бұрын
هل يمكن تعليمي كيف تصنع المثقاب 12V
@ELOTROLADO2.0
@ELOTROLADO2.0 Жыл бұрын
hi you are the prorpety have a cuestion for you to better your develop magnet from spain
@MakeElectricity
@MakeElectricity 2 ай бұрын
i wish i could build this
@germana.victoriapizo559
@germana.victoriapizo559 Жыл бұрын
¿ Que cabezal láser utilizas ?
@joseangelalonsoregidor
@joseangelalonsoregidor 2 жыл бұрын
Se puede hacer motores y generadores con imanes temporales que no se hacen con tierras raras
@markkevin7245
@markkevin7245 Жыл бұрын
Hi there do you have the files for light burn so I can print on my laser?
@edsonferraz1
@edsonferraz1 Жыл бұрын
Congratulations!! excelant generator. Do you can send me details of coil?
@BuildingFromScratch
@BuildingFromScratch Жыл бұрын
Here is the link to the video where he made the coil kzbin.info/www/bejne/eIiUpYNper55gNk I just wish we could get a copy of the coil holder so I could 3D print it or have it cut in the plexiglass.
@pejuangkeadilan9070
@pejuangkeadilan9070 2 жыл бұрын
like my design in 2017 with acrylic case
@chunwahtse6713
@chunwahtse6713 2 ай бұрын
那世界这样不用進又好看他的還要講的一大些話太沒有面講錢???我是一個老人知道嗎....
@Rafaeljotiar
@Rafaeljotiar 3 ай бұрын
You never explain in details about magnets and it’s polarity arrangement
@mamunulhasanmamun8751
@mamunulhasanmamun8751 2 жыл бұрын
excilent.
@scott32714keiser
@scott32714keiser 27 күн бұрын
i dont like ac generators because if you want a perfect 60hz you need to set the rpms just right for it to work right but its a trade off if you wan to charge batteries dc generator is cheaper but of you want to power modern technology ac is cheaper. with ac you need diodes to charge batteries but with dc you need a inverter. overall ac is cheaper
@parandhanchakma7551
@parandhanchakma7551 2 жыл бұрын
Nice
@El_comentate
@El_comentate Жыл бұрын
кто знает подскажите пожалуйста что за модель мультиметра? спасибо
@ramiroalvesdemattos5312
@ramiroalvesdemattos5312 Жыл бұрын
Vai ter para venda
@vladimirlenin843
@vladimirlenin843 2 жыл бұрын
How am i supposed to get drill rpm at daily life
@sensei_dm
@sensei_dm 2 жыл бұрын
How can one get access to the 3d files ?
@linoross7493
@linoross7493 9 ай бұрын
Very not good. Only one half of the magnetic induction is used. The other half is wasted.
@thetrue1636
@thetrue1636 Жыл бұрын
how RPM each motor ??
@ramupandey4674
@ramupandey4674 2 жыл бұрын
Looking same design
@expertknowledge5512
@expertknowledge5512 2 жыл бұрын
Yes
@VannhungLee
@VannhungLee 5 ай бұрын
🇺🇸 🇺🇸 🇺🇸 🏢🏫🏫👍👍🍷🍷 🫱🫱🍷🍷💛💛🌻🌻🌻🌻🌻🌻🌻🌻 🌏 💛💛💛 🇺🇸 🇺🇸 🇺🇸 That Tuyet Voi Cam On Thay Giao : San Xuat Dien Gia Dinh mien Phi
@ВалераРовбо-э3е
@ВалераРовбо-э3е Жыл бұрын
Якщ крутити катушку і магніти в різні сторони. Буде 5о вольт.
@ferencszabo3504
@ferencszabo3504 Жыл бұрын
250w to make 250w …?
@stels322
@stels322 9 ай бұрын
В моей стране похоже законы физики другие и мой подобный генератор не работает как хотелось
@chunwahtse6713
@chunwahtse6713 2 ай бұрын
❤❤❤❤❤❤❤❤❤❤😂😊
@yeyin777
@yeyin777 Жыл бұрын
Cuál es la gracia? Es un dínamo de bicicleta...
@JeffyJeff01
@JeffyJeff01 5 күн бұрын
Sixteen minutes and thirty seconds of the worst music loop ever devised by humanity. The video is worth a watch, but with the sound off.
@sensei_dm
@sensei_dm 2 жыл бұрын
I see that you never reply any comment or even emails
@Duy-AUDIO
@Duy-AUDIO 2 жыл бұрын
toi muon dac lam giong cai nay
@satpalmanhare95
@satpalmanhare95 Жыл бұрын
Yah wala saman banakar doge to kitne mein doge bhai
@gocluomer9583
@gocluomer9583 Жыл бұрын
Befendi bana bir tane yapıp gönderebilirmisin Kaç dolarsa paranı ödeyim lütfen. Merci
@Mahesa_Pamungkas
@Mahesa_Pamungkas Жыл бұрын
Engineer is not same with art Mr, that waste time
@hijodeperrilla1
@hijodeperrilla1 5 ай бұрын
fack, ¨_¨ thank you
@MuhamadRidwan-pq6wk
@MuhamadRidwan-pq6wk 2 жыл бұрын
Third 👍
@mannybelo8410
@mannybelo8410 Жыл бұрын
You think I am an idiot?
@shienkalitvinov
@shienkalitvinov Жыл бұрын
seems weak
@davey2k12
@davey2k12 Жыл бұрын
Very noisy very inefficient 🤣🤣🤣
@hectorconde5452
@hectorconde5452 3 ай бұрын
terrible music and annoying
3D printed alternator for micro-wind turbine
11:55
Dominique H
Рет қаралды 232 М.
HIGH SPEED BRUSHLESS MOTOR PROJECT - 100,000 RPM BRUSHLESS MOTOR TRIAL
18:09
Человек паук уже не тот
00:32
Miracle
Рет қаралды 4,2 МЛН
The Singing Challenge #joker #Harriet Quinn
00:35
佐助与鸣人
Рет қаралды 36 МЛН
Make a GENERATOR
14:26
Electronoobs
Рет қаралды 314 М.
Building a Generator
12:36
Tim Station
Рет қаралды 1,4 МЛН
NEW FREE ENERGY GENERATOR 20KW - FREE ENERGY FOREVER
33:35
The Liberty Engine Project
Рет қаралды 2 МЛН
How to make small generator
20:24
American Tech
Рет қаралды 376 М.
Making a Fully Functional Jet Engine using Soda can | diy Jet Engine
16:27
4000 Watts hydrogen generator HHO
14:25
I'm just DIYer
Рет қаралды 4,8 МЛН