AtomRC Dolphin 188MPH 303km/h 12S 50.4V setup

Рет қаралды 6,435

Ай бұрын

airframe : AtomRC Dolphin 845mm
Motor : BrotherHobby Special Edition V4 32.5-12 580Kv
ESC : Flycolor X-CROSS HV3 80A
Prop : Schulze luftschrauben Super-S speed line 8x6
Servo : Blue Bird BMS-125WV
FC : matek F411-WSE + INAV 7.1.0
Battery : 2 of Tattu R-Line 6S 1400mAh
The motor and batteries are a little bit heavy.
For saving the weight, I'll replace motor, prop and battery in below.
- motor : amax 2806/650Kv
- prop : 6.5x6.5
- battery : 2 of Tattu R-Line 6S 1050mAh
2024.05.15.
I was tested amax 2806/650Kv and 6.5 prop. It is not good than the initial setup.
I'll test brotherhobby's 2816 size motor.
I want to get more RPM.
BGM : BGMer

Пікірлер: 31

@RubyS.1 Ай бұрын

Nice work. Not any easy plane to make fast but you did. Try the heewing F01 next.

@celeselements Ай бұрын

F01 seems to be a speed machine, I'll think about it.

@cookieRELATIVELY 20 күн бұрын

and in general this esc definitely has telemetry. and I'm not sure but it seems to have a current sensor, so in the settings this can be configured if you connect the TX esc to the flight controller

@celeselements 19 күн бұрын

Thank you! I'll check it!

@craigcupit1917 Ай бұрын

Cool, what is that software, is it on github, did you use to map your telemetry and speed from I assume edgetx SD logs?

@celeselements Ай бұрын

Thank you! Set SD log on your TX(special function) and get telemetry file, And drag and drop on otxui( maxbl4.github.io/otx/index.html ). Check the keyword "otxui".

@narnasqueneth Ай бұрын

Very cool video. Your current measurement seems to be very low; 0.6A?

@masoncolley8822 Ай бұрын

It’s because he’s running the esc straight from the battery so the fc can’t measure current draw from esc

@RCDUDEFPV Ай бұрын

Thumbs up

@celeselements Ай бұрын

Thank you!

@torukclaus937 Ай бұрын

Hello, I like the idea, a question, how do you use this engine with 12s, if the manufacturer says for 6s. It doesn't heat up, what consumption does it have

@celeselements Ай бұрын

I didn't check the current. Typical performance FBL RC helis run on 12S and around 500Kv motor, I referred to it.

@amirazim1214 29 күн бұрын

Its not 6s when u combine 2 6s together, only thing will be added is the total mah oh the battery,

@torukclaus937 29 күн бұрын

Hello, yes now, 6s is parallel, not series. Thank you

@brkfpv60 14 күн бұрын

You cannot see the real GPS speed while diving, there is not much advantage in doing 12s. It is possible to reach these speeds with 6s and a high pitch propeller and a high kv motor . good flights

@celeselements 13 күн бұрын

Thank you. Honestly I have a fantasy about high voltage. I think 12S seem to have an advantage in maintaining voltage(less Vsag).

@Cocopuff55 Ай бұрын

Tape ?

@celeselements Ай бұрын

Tape to prevent hatch drop at high speed.

@giuroy Ай бұрын

i mean cool the setup at 12s, but whats the point on going 12s to only get to 188mph? a goblin will do better than that at 6s (2814 2000kv 6.5x6.5)

@celeselements Ай бұрын

12S have better voltage sustaining under load than 6S. Strix Goblin is also cool!

@furyianman5157 Ай бұрын

Why do you care what someone else does with their time

@cookieRELATIVELY 20 күн бұрын

Friend, according to my calculations, this configuration has reached its limit, why don't you try tmotor 3115 1050kv-900kv with 6inch propeller 12s 900kv - 6 inch prop 12s 1050kv - 5.5 inch prop

@celeselements 19 күн бұрын

Thank you for advice! At initial setup, I refer the performance FBL helis, it run 12S and around 500Kv motor. I'm testing it by increasing the motor Kv little by little. In my opinion, the 3115 motor is a little bit heavy for my configuration, I want it to be less than 100g.

@cookieRELATIVELY 19 күн бұрын

@@celeselements then it makes sense to consider RCINPOWER AOS Supernova 2807, as they say this is one of the best engines, but it has 1400kv so it will have to be used with 8s