Audi 2.2 10VT Dyno 537hp 600nm

[@nenume00]

would love to see the dynosheet; Good to see that the project is alive, congrats on your hard work

[@sumalei]

Thanks. Check the other dyno video, at the end you will see dynosheet

[@futuredinghy]

Sounds awesome nice job!

[@sumalei]

Thanks

[@emsis1990]

Brutal sound 🥰

[@zygisis]

Nice hp numbers, nice sound

[@maler88]

Bomb ! 🔥

[@karlesser9541]

OMG 😱 Soooo nice!

[@zyankali2357]

Der Kotflügel Bremst den reifen 😂😂😂❤❤

[@dennismerk2229]

das tut weh beim zuschauen

[@zyankali2357]

​@@dennismerk2229 weil du nur einen Corsa fährst? Da würde mir auch alles weh tun

[@dennismerk2229]

@@zyankali2357 ziemlich subjektiv, findest du nicht? und ich fahre uebrigens ein audi 80 1.9tdi

[@zyankali2357]

@@dennismerk2229 hatte ich auch sehr guter Motor mit VEP . Jetzt 1.8 mit MKB . BAM und ein 2.3 5zyl Audi Avant

[@dennismerk2229]

@@zyankali2357 poa 2.3 im Avant ist ein traum, 10v Nehm ich an?

[@Bizonas]

Yes sir!!

[@Foscora]

Oh good job, not many 10VT doing these kind of numbers!

[@BigDankJuicyBlunts]

Sick, very inspiring for my build. Are you using the stock audi trigger? I’ve got a lightweight FW, it worked with the CIS so I’m sure it would for vems?

[@sumalei]

Few years ago I was using auditrigger it worked quite ok with vems, but now im running 60-2 in the rear seal. It should work if there's one reference pin at the back of flywheel

[@BigDankJuicyBlunts]

Would you recommend going 60-2 rear main from the start? Any tips or special tools for installing it? Thankyou sir

[@sumalei]

@@BigDankJuicyBlunts yes i would reccomend using 60-2 if you have a chance, since its easier to setup and its more reliable. You dont need any special tools, seal has special adapter to install it

[@thomastournier4521]

Waouw impressionnant pour un 10v moteur KG ? Quel est la configuration des pieces moteurs pour cette puissance ?

[@sumalei]

MC engine, check description there are some specs

[@aleksej8034]

Nice Audi!🔥🔥🔥Stock Camshaft?

[@sumalei]

Thanks. Not stock, Catcams 282/276 cam

[@aleksej8034]

Boost?and fuel E98?

[@sumalei]

@@aleksej8034 2.4 bar with E85. Check description

[@aleksej8034]

Sorry,dont see😅Just i have MC block,and NF head 2.0bar boost,and 500hp 550nm E98.7000rpm.HX40.Just interesting yours specs.Thanks you.

[@sumalei]

​@@aleksej8034good numbers. Im also using same setup, MC bottom with NF head. We could have made more power but alternator started to drop voltage at higher rpm, and dwell timing was extending and started to missfire. I fixed this issue now, so next plant is to make 600 hp 💪

[@damianolczyk3496]

Great car. Standard cluch?

[@sumalei]

Thanks. 6 pad ceramic clutch disk + 20VT 3B pressure plate

[@petroldrinker88]

Nice, now I finishing my audi 90 q 10vt but i think it will be 350hp or somethink like this. What you change to have that power?

[@sumalei]

Check description below video

[@petroldrinker88]

​@@sumalei Why you change valve springs? In catalog catcams this camshaft can work with OEM springs.

[@sumalei]

​@@petroldrinker88i changed valve springs because i had valve float under boost, i couldnt even reach 6500rpm

[@wojciechszymanski998]

Hi , I have the same engine and my goal is 300-400 HP . Can You tell me what upgrades I have to do ??

[@sumalei]

Hi, i can tell you, do you have messenger?

[@Torsen55]

Колеса арки не протирают?

[@TomGT59]

Opa 🇱🇹

[@buba19888ify]

Stock pistons?🤔

[@sumalei]

Yes

[@buba19888ify]

This is MC engine?

[@sumalei]

@@buba19888ify Yes MC

[@Wolfy_11234]

Stock internals?

[@sumalei]

Forged rods. See description

[@karlesser9541]

what kind of budget do you think I need to make this performance?

[@sumalei]

Its really hard to tell, depends on location that you live. Personally I think I have 3-4k euros under the hood now roughly

[@vitkovic57]

@@sumalei hi, where did you get the work done? And i've been told that the 20v block can handle sputter bearings while the 10v cannot. You had no issue with this?

[@sumalei]

​@@vitkovic57hi, I did everything myself. Sputter bearings is just technology of coating, so I can't see why it wouldn't work between these two engines. I'm using King Racing bearings, I haven't had problem with that

[@karlesser9541]

@@sumalei can i write you an email? I still have questions about the conversion, my 10v should also get the power.

[@sumalei]

​@@karlesser9541of course

[@TaZzeuR18]

salut comment tu a fais pour connecter ton ecu sen capteur pmh

[@sumalei]

English?

[@TaZzeuR18]

Hi, how did you connect the pmh on the hall effect to you a diagram of the connection you made? How much power did you get with the 440cc injectors?

[@sumalei]

@@TaZzeuR18 hi, what is pmh? 440cc injectors maxes out at about 300hp with 95 fuel, and even less hp with ethanol

[@TaZzeuR18]

Do you have a Messenger to talk about it?

[@TaZzeuR18]

How did you do for the cam tree sensor report?

[@Crediu]

my dad has audi b4 2.0 and it makes i think 90hp and yours is 2.2 and makes 5.5x as much

[@wryukeng]

hp

[@karlesser9541]

Do you have Instagram?

[@sumalei]

No, i dont have

[@schwuppdiewupp7]

@@sumaleichad