Audi A8 Allroad air suspension calibration and lowering 402 mod DIY by Edge Motors

www.EdgeMotors.com
PLEASE LIKE AND SHARE THIS PAGE!!!
In this video we show you how to calibrate the air suspension in Audi's with air ride after repairs, and how to calibrate it to be lower.
attempt to perform this procedure at your own risk, we are not responsible for any damages associated with using this video as a guide .
Edge Motors
[phone]
[e-mail]
107 E Railroad ave
West Haverstraw NY 10993
www.EdgeMotors.com

[@LeTRANSPORTEUR69]

*hello my Audi Q7 is very raised on the right side and crushed on the left side I can not calibrate it it always remains in the air I have so much value that I do not know what to enter do you have any idea how can we put it back to the factory?*

[@EDGEMOTORS]

Was it ok before you tried to calibrate?

[@daniel540]

Just to confirm, front left means the driver’s side for left-hand drive, perspective from sitting inside the driver’s seat?

[@olofdaisler9121]

can i raise the air suspensions beyond the raised position? a taller setting, like the one of the A6 allroad

[@TheRafalblog]

thanks for this video now I'm more familiar with how it works. I spotted left side in my Audi A8 is higher 10mm than right side - front. Do you know what can a be?

[@mendez77054ify]

TheRafalblog did you ever figure it out? I have the same issue.

[@sarmadalqaysi2199]

Hi thanks for this info, question, I have audi a7 2013 and it has the driver side highest then passenger side, how I can fix it please?

[@chrisroser8645]

Great video. This is for the C5 A6 allroad. Your title say's A8.

[@AndreasKristiansen]

Very nice video and well explained! Thank you for sharing! :-)

[@MrLeewsee]

would love to see you do a vid on valve guide seal replacement on 1.8T

[@EDGEMOTORS]

you could use a video we have on 2.7t valve guide seals replacement... pretty much same thing.

[@remyhorsdage8045]

Would the car throw a code if one of the wheels was out of calibration?

[@dilaro4]

Thank you for the video. The problems that are occurring for me after calibration is that it sometimes tells me invalid . And at channel 5 it tells me error, I can't put any value.

[@EDGEMOTORS]

that ussualy mean that the value you putting in is way too far out of range and the ecu thinks that the ar is not on the level ground.

[@dilawerchahin7553]

EDGEMOTORS The thing is I tried lowering it by 20 MM by raising to 416 from 396 at the front, but it would tell me invaild/vaild sometimes

[@SSH-mw6by]

Do you know how i can remove the auto-lowering feature on my 2013 s8? If the car is in “raised” position, after 30mph the car will auto-lower. I want to change this and enter a higher speed, lets say 60mph, then it can lower.

[@michalpiszczat7823]

Can you tell me how long take connection in adaptation to first channel? I have the same value 416 but can't connect to first channel= left front wheel....before u do this u hd orange control of air suspession?

[@mustafasolmaz5946]

Which interface did you use?

[@emerlynnelson170]

You guys rocks!

[@TheFoxfy]

How much mm is the maximum lowering the car can take ? Is there any maximum or I can lower it as much as I want until it hits the fender ?

[@EDGEMOTORS]

Well you can physically lower it to what ever you want, but when you lower it, the shock o sorbets won’t work anymore and will go bad really fast also ride quality will suck

[@valehamosk8660]

Where do you find security access codes

[@EDGEMOTORS]

In repair manuals

[@jameswan670]

Why height can be differ by wheel? Doesn't it need to be same for all wheels?

[@EDGEMOTORS]

The shape of the body may be different, so the car needs to set the height according to the geometry, not the distance from the fender to the wheel

[@ralphyplayanum1]

wanted to no if wen u start the process it should be on comfort or dynamic

[@EDGEMOTORS]

+ralphyplayanum1 it dont matter... the car will put it self into the setting it has to be for the adjustment...

[@ralphyplayanum1]

Keep say no response from controller why

[@ralphyplayanum1]

I jus called for you surge but you werent in

[@douglassenriquez423]

what is you cannot click the security access button due to fault codes? when the computer is hooked up on the vcds the security button is unavailable due to fault codes how can I get past this? some one help me please!

[@christinerose9561]

I saw one today on a lot and the back seem lower than the front tires. Does that mean it needs a calibration? They told me it will go back up once the car is turned on. Don't know if they are tricking me or not.

[@EDGEMOTORS]

+Christine Hannah could be, but if you strt it up and it goes up, that means that the bags are leaking... its not supposed to sag while sitting....

[@christinerose9561]

+EDGEMOTORS that's what I thought. Thanks..

[@haimodelu]

+EDGEMOTORS depends.When you drive it rise up a little bit, so it gives you a bit more clearance.. But when you park the car it "sits down".. use lowering links and on Sports air suspension , swap to SE module. Cause SE module lowers car when you set to "sport mode" and raise up if you set "comfortable" mode

[@christinerose9561]

Thanks! I didn't buy it. I knew it was damaged. I got a 05 D3 and it does "sit" a tiny bit when ignition is off then lifts when turned on. It also lowers pass I think 60mph for over a few seconds for a sporty feel and lifts when you stop. I'm learning my car. It's so much stuff! !!!!!

[@blacksheep407.]

How can I reset it to the factory settings?

[@EDGEMOTORS]

Just put in the actual measurements when you do the adaptation…

[@adriesb.478]

Every time I enter the security access it’s lets me in but after doing one wheel it kick me out. Then I can’t log back in I have to unplug the scanner and stared all over in 15 min. 2007 Audi Q7 only one code I have calibration not learned. This all happened when My air pump stop working and I replaced it. Please advice me.

[@EDGEMOTORS]

You might be entering a number outside specifications, or too far from other wheels.

[@geirkleven3936]

Did you figure this out ? maybe a batteri dissconect will help ? Same ting is happening to me after doing four wheels, wount let me save in block five

[@jay305ify]

what happen if you do not clear the codes..?

[@jijkourumov]

Why are you putting a bigger number if you want to lower the car?I don't get that.Bigger number means that you have more distance between the center of the wheel to the top .Why is that???

[@EDGEMOTORS]

So the computer thinks it’s too high, and lowers it......

[@jijkourumov]

@@EDGEMOTORS ,oooooookkk,now I know what you mean.Thanks

[@vtec70]

Do you have the security code for 2012 A6 3.0tfsi? I would love to lower my ride.

[@EDGEMOTORS]

www.ross-tech.com/vag-com/cars/levelcontrol.html check this

[@dilaro4]

What cable do you recommend?

[@EDGEMOTORS]

vag-com ross-tech.com

[@ralphyplayanum1]

i want to drop as much as possible

[@birogabor5200]

A8 allroad????

[@EDGEMOTORS]

A8, allroad

[@Thunderd0me]

No allroad, quattro......

[@EDGEMOTORS]

This video works for Audi A8 and Audi Allroad with air suspension.

[@douglassenriquez423]

*what if