In this video i demonstrate how to perform the EPB rear brake pad replacement on all newer style Audi vehicles. Thank you for viewing
Пікірлер: 50
@jeanboudreault8672 Жыл бұрын
Thanks for the video. I have a 2018 Audi Q7 and there is no need to connect the OBD2 to disable the electric parking brake. Simply follow the sequence in this video and the parking brake will be disable
@AutoMotiv8ed Жыл бұрын
Thanks for the info!
@Snowdog2163 жыл бұрын
Good info, Thanks. If you are in the northern US (or similar conditions), places like Buffalo, Cleveland, Detroit, Chicago, etc, there is a lot of snow and they use road salt, I would want to put in new slide rail hardware, and for me, I take the caliper bracket off and remove any rust and debris, with a file and dremmel tool, then put in new hardware. Dry fit the pads to make sure they do not bind. If so, more cleaning may be required, there are other videos on that. Again it depends on the age of the vehicle and condition, etc, but something to be aware of.
@AutoMotiv8ed3 жыл бұрын
thank you good info!
@tebogotebogo80043 жыл бұрын
But you guys don't explain bolts/nuts sizes on brake pads calipers, so what sizes do we have to use
@turnerboland42782 жыл бұрын
I hooked up the caliber to my car battery and that unlocked the electric brake too. Much easier and cheaper than buying the computer stuff
@AutoMotiv8ed2 жыл бұрын
be caufefully become somtimes audi's may not like to be done this way and can cause other issues, best to do it the way manufacturer recommends
@fastlanetechnologies25123 ай бұрын
How did you hook it up to the car battery?
@JoseMartinez-bf7hd Жыл бұрын
What scanner tool are you using?
@davidjuarez22153 жыл бұрын
Thank you very much. This process also works with Carista
@AutoMotiv8ed3 жыл бұрын
You're welcome!
@raphael93393 жыл бұрын
Does the caliper piston need to be rotated while being compressed, or is it compression only? Which compression tool make/model are you using?
@raphael93393 жыл бұрын
I believe it's compression only.
@AutoMotiv8ed3 жыл бұрын
compression only!
@RIZZO0373 жыл бұрын
What computer are you using to Talk to the Car?
@nydrell19693 жыл бұрын
Ok guys to hell with all this fancy stuff there are 3 easier ways 1.use carista 2.get a battery and 2 pieces of wire unplug the brake motor touch the wires on the connector or 3.take the 2 bolts off the motor. slightly turn to the side and wind the torx bolt inside all the way to the right until it stops. BAM .there you go pop thise pads out
@mrj4864Ай бұрын
Why can you just leave the car in neutral when u turn the car off?
@phillm1564 жыл бұрын
Can you bypass the parking brake by simply unplugging it?? It’s a simple 2 wire system , either on or off.
@AutoMotiv8ed4 жыл бұрын
Hi @Phill M156 Not sure have never tried, i do not recommend as these newer European vehicles start becoming very sensitive when being tampered with
@BaveRAWWR4 жыл бұрын
You can also get an OBDELEVEN, pro from the main website around for 30$.
@konstantinasnikonorycevas76153 жыл бұрын
Thanks ! very much !
@phillm1563 жыл бұрын
I just changed the rear pads on my 17 SQ5. The rear parking brakes are a 2 wire system. Unplugging it is simple and prevent it from getting in the way. checked with an older 2010 Q5 and it’s the same.
@spannerman73593 жыл бұрын
Why are you manually winding the calliper back if the computer has already wound them off?
@benjumper88382 жыл бұрын
13 and 15 mm for the 2 bolts and a torx head for the screw holding the rotor on
@Orchid9Ghost2 жыл бұрын
The computer retracts the E-Brake, the calipers don't retract when you retract E-brake.
@shaquanshapiff71834 жыл бұрын
i really appreciate the time you took this is very informative
@AutoMotiv8ed4 жыл бұрын
@shaquan shapiff718 thank you for your feedback 🙏🙏
@justasimpleman79483 жыл бұрын
How much does this cost
@ObieoneKoala3 жыл бұрын
please do some very clear very precise BIG THANKYOU
@AutoMotiv8ed3 жыл бұрын
thank you
@LEVUCARCHANNEL4 жыл бұрын
Thank you for sharing, very effective and fast
@AutoMotiv8ed4 жыл бұрын
@LEVUCAR CHANNEL thank you for your comments 🙏
@eseybold13 жыл бұрын
very helpful - thank you
@AutoMotiv8ed3 жыл бұрын
You're welcome!
@abdulrezak9393 жыл бұрын
Do we need obd reader to change front brakes?
@AutoMotiv8ed3 жыл бұрын
No, just for the electric park brakes in the rear
@issafanafana94733 жыл бұрын
Good day. I've jc changed my rear brake padz, but they are not working when bleeding them. What else can I do?
@issafanafana94733 жыл бұрын
The car is audi Q5 2013
@AutoMotiv8ed3 жыл бұрын
@@issafanafana9473 make sure you have exited the maintenance mode after you have finished installation
@konstantinasnikonorycevas76153 жыл бұрын
Thank you very much.!
@AutoMotiv8ed3 жыл бұрын
@Konstantinas Nikonorycevas thank you 🙏🙏
@ramanazifi Жыл бұрын
Are you in Melbourne?
@AutoMotiv8ed Жыл бұрын
No i am in Sydney
@pianoman424214 жыл бұрын
Very helpful thanks for taking the time.
@AutoMotiv8ed4 жыл бұрын
@My two cents Thank you so much i appreciate your comments
@pianoman424214 жыл бұрын
@@AutoMotiv8ed a question, did you leave the diagnosis device plugged in whilst changing the pads? If so did u have a battery charger connected? As I've heard if the battery goes flat, game over. Cheers
@AutoMotiv8ed4 жыл бұрын
@@pianoman42421 Hi, yes the computer was connected and yes battery was connected to back up power while doing so! However, If you dont have access to back up power, it can still be done. Once you wind piston back, you can turn car ignition off, and re enter the setting to finalize brake change once both sides are complete. Hope this helps