Audient iD4 MKII and iD14 MKII - Audio Interface Review

[@bluesmanj]

Your in-depth reviews of interfaces helped a lot in my decision making process! Now I’m able to make a educated purchase based on facts, and my needs, as opposed to buying a product based on hype, and sales tactics. Thanks Julian, and keep up the good work!

[@JulianKrause]

Glad you enjoy the videos! Thanks for the support 🙏

[@JulianKrause]

1. Correction: At 07:00 the sample rate should say 96 kHz. 2. Regarding the interference in the preamp noise sample: Some people have pointed out that you can hear a tiny amount of interference at 10:03. I went back and checked the recorded noise. For the test I recorded a few minutes of preamp noise and for about seconds you can hear a low 300 Hz hum. For the video I apparently picked a section from exactly these 12 seconds. I wasn't able to replicate this hum and this wouldn't be audible in a normal recording situation. Treat the noise preamp noise sample of the iD4 MKII as a worst-case scenario.

[@lerlerler1]

I believe type-c and tipe-A makes no difference. Maybe the reason is your usb type-a is also usb2 not usb3 standard.

[@reinulf656]

Dear Julian... Was your USB-c to USB-a cable USB 3?

[@andrewherrera9769]

@@lerlerler1 Nope, type C allows greater power delivery

[@f5770]

yes I was writing about the 192khz, and thank you for the uhm 300hz noise info, it is something I wouldn't expect by this interfaces but actually it's quite difficult to notice it in normal situations. Does the problem appear only on the id4 or does it also with the id14?

[@lerlerler1]

@@andrewherrera9769 type c is a port, there is nothing about power delivery. Usb3 provides more power then usb2. Regardless of type c or a or b or whatever else.

[@freezeframeplease]

this video made me buy an iD14 and boy i don't regret it. Thanks again Julian

[@rune7066]

After 3 years it was good ?

[@ExitOnTheInside]

2nd this comment! Still Happy?

[@rune7066]

@@ExitOnTheInside i just get one all perfect it’s have one issue tho i use it always even if I’m not doing music the issue with this audio interface is that I have from time to time to in plug + plug the usb cuz it’s just stopped working. It’s have new update I didn’t do it yet it may be something for this issue . I’m happy with this card but after 2 months 0 song I’ll switch to uad solo

[@orkundemirayak]

Hello Julian, I'm a bass player of nearly 15 years and recently started home recording. Your videos are invaluable for my research and I cannot appreciate enough how well made they are. Thank you for all of your efforts which enable us to have this information freely available on KZbin.

[@yakov.lopatin]

Hello. What audio interface did you buy?

[@orkundemirayak]

@@yakov.lopatin hi. I bought an Audient id4 mk2 and am happy with it.

[@paul_london]

Just bought id14 mk2, it's way better than mAudio192|6 and Evo4. Plenty of gain, no cracking noise, no interference with 3g. Love it

[@somerudedudeeee]

is it possible to record two guitars at the same time with id14 mk2?

[@21recordsmix]

​@@somerudedudeeeeyes there is two inputs in the interface

[@leandronicolas8848]

Great review! the numbers on the chart seem crazy good. I don't think they warrant an upgrade for those who own the old version but it's nice to see them improve on them. It's especially nice to see them improve on the volume knob. It seems for level imput meters motu m2 is still king in this price range. Cheers!

[@oltech512]

Thanks Julian, just made my purchase and I'm delighted with the iD14. Your review was a tremendous help as I still count myself as a newby to home studio building.

[@Skreept]

I just ordered an id14 After watching almost all your reviews. Thank you for the effort you put in this videos

[@actioncameraspro]

How was it?

[@BL-yj2wp]

Perfect timing, I was wondering.

[@julius.kmitas]

Julian, thank you for your reviews. Thanks to you, I've chosen Audient iD4 as my new interface. I need to be at several places trough the day, and this interface is perfect for carrying with me. It's robust, quality is great and that wheel..! Amazing. Keep up the great work! Greetings from Lithuania!

[@aliroustai2468]

You are by far the best. Thank you for your clear precise and intelligent reviews.

[@virgilebeats3041]

Bought the iD4 from watching a few of your videos. Thank you so much for being the best interface reviewer on youtube.

[@tommigronlund714]

Brilliant review, thanks. I have iD4 Mk I and this confirms that I have made a good choice but maybe not yet upgrading to Mk II as the first one still is amongst the best ones out there.

[@okay1904]

If I had to buy a 2 input device, for a typical home studio, it would be the ID 14 Mk 2. Not exactly cheap, but relatively decent quality, and decent features. The ID 4 is also a great device for someone who is not likely to record any stereo inputs. A good achievement. Output dynamic range over 125dB - awesome.

[@xyzct]

I bought the 4 and am kicking myself for not getting the 14.

[@xyzct]

x

[@pds1455]

@@xyzct but there is no difference in sound quality. It has the same chip . Only difference is software and the number of in & output .

[@Vercoquin64]

Why ?@@xyzct

[@brucerain2106]

So hard to decide tbh idk if I should get a Scarlett, volt 2 or id14

[@Joaonunokendall]

It will be interesting and useful to see the iD44 measured and reviewed by you Julian.Nice work!👏👏👏

[@DarkPa1adin]

best technical audio interface review! well done!

[@matthewphelps1330]

I got mine two days ago and have been loving mine. Waiting for my guitar to arrive still though

[@kevc6115]

I got my 1 a motnh ago! Happy out 😁

[@Teeum5]

Of course I gave this video a „thumbs up“ because you absolutely deserve it. Such a great amount of work you must have put into this video… But I must say… since I‘ve never dealt with recording technology, I don‘t understand a word at all. If only I had paid attention in physics class… 🧐

[@Geodrik83]

I feel so good for my audient id44, which have the same DAC .. excellent job audient again.. serious company.. antelope sorry, with the double price you can't reach that thing.. bravo julian

[@VallyTheHitman]

So the id44 and id14mkll have the same dac?

[@ivansaniasin896]

@@VallyTheHitman ADC/DAC same 100% in this two.

[@Geodrik83]

The DAC is same .. The ADC is different chip. for the id44 is the ak5578

[@teashea1]

The best reviews - so well done

[@fredericfx5352]

Great review, I went with the ID14 MKII for the windows 7 compatibility and for is incredibly critical details in audio spectrum 👍🙂

[@JTCPingas]

Windows 7 in 2021. Mate, just upgrade to Windows 10.

[@fredericfx5352]

@@JTCPingas I have a stable machine, don't need a upgrade as far is not connected to the net.

[@joymondal3211]

Very nice very well managed video... Thanks a lot 🙏

[@bahathir_]

The audio output's distortion is unmeasurable.. Time to upgrade the audio analyzer.. :) We have found excellent DAC.. Thank you for the review.

[@Remixed_By_Mus-T]

Julian macht einfach die besten reviews! / this guy makes the best review`s ever

[@IgnacioVS]

I love the way you review everything, it's always everything that you really really need to know that most forget. Thanks alot!

[@swedemaximus]

Got the id4 mkii a week ago and it's great!

[@techinspect6434]

One aspect that should be regarded in EVERY USB Bus powered audio interface test is: how stable does it work when bus power is not clean? How much ripple can it handle? What are the exact power requirements? How does it react to CPU induced noise on the host machine? Does noise couple through or is it filtered out? I'm a developer of electronics and all these figures stated have no value if the customer cannot reproduce them. In my view USB bus powered interfaces are highly dependent on the power supply of their host machine. Even this video has crackling, a comment pointed out crackling at 14:27. What's the point in having a noise floor of xy, and a dynamic range of z, if there is a very audible glitch when using this interface? To put it in German: den Wald vor lauter Bäumen nicht sehen...

[@lerlerler1]

Thanks for the review. I especially wanted to see yours one.

[@ultimatemetalguitartones]

Just bought the ID14 MKII! Perfect timing!

[@vince8081]

What a great work here, welldone !!

[@thois]

great quality! Thanks for your objective and analytical review! Keep up

[@otmsnp]

I have been using it for 2 weeks ,preamps very clean & i expected good DAC quality

[@beatsbybood]

great video which really helped me to understand the product and enabled me to decide on what was best for me! thanks v much dude, keep up the great work

[@dawikhawi8674]

THank you for everything man!

[@prankmeteors1203]

One other thing that I think bears mentioning is the top-mounted controls, which I find a lot easier to use compared to the front-mounted controls on other budget interfaces like the MOTU and Focusrite.

[@Jpetersson]

I have the iD4mkII and love it, first time I can record vocals and not have to do any noise reduction in post, so very quiet preamps in deed. I do however need more inputs and outputs so I ordered a iD14mkII today! I can use a ASIO buffer size as low as 16 and have virtually no latency with vst fx or instruments. You need to increase the buffer size as you load more and more plugins obviously.This also depends on your cpu power. You want to connect this to a usb c port if possible which sends more power to the interface than a usb 2 port does. Increases headphone volume amongst other things.

[@Vercoquin64]

why do you need more inputs and outputs ?

[@AironExTv]

Thank you. I appreciate the fine details of this review. Most helpful.

[@8man_01]

I bought the ID4 MkII as no sellers had the Motu M2 in stock but there weren't enough reviews at the time. This review would've given me confidence at the time but I'm beyond than satisfied with the ID4 MkII! Also the full licensed software and lessons it comes with really makes it worth it. The JFET instrument input is also a positive though not really having much experience with a lot of guitar amps, I couldn't make a fair comparison. I'm just happy I don't have to use my motherboard's noisy line-in and mic-in anymore. Now just to fix my house's lack of proper grounding... yay old house.

[@TheAvatarVV]

just buy a di-box, ground problem solved

[@lance134679]

Thanks for the review. It seems these are some of the best in the business. I think the lack of input metering is a big downside, but the performance is definitely acceptable.

[@schoebelski6602]

excellent reviews on your channel - many thanks 👍👍👍

[@jeffbarkley8360]

Thanks for the excellent review, Julian. I purchased an Audient iD14 MKII a couple of days ago. I have a MOTU M4 but my wife tried it on her PC and she likes it. The MOTU is no longer in stock here so I tried the Audient. I was a bit worried that it would end up not being good performing, so I'm very happy to see your results.

[@butcher_0392]

But due to the bad reputation audient has, I would choose ssl 2 or Motu over id14. Just Google "AUDIENT INTERFACE DIED AFTER ONE YEAR OF USE" and you will see how many people are disappointed.

[@reinulf656]

@@butcher_0392 I can't find anything.. Can you help with where to see this information? I googled it with and without quotation marks

[@butcher_0392]

@@reinulf656 I just Google and I got these results: www.soundonsound.com/forum/viewtopic.php?f=15&t=74871&p=719920&hilit= gearspace.com/board/music-computers/1168648-audient-id22-disappointment.html www.amazon.com/-/es/gp/customer-reviews/R2CBO3XXPIPBNQ/ref=cm_cr_arp_d_viewpnt?ie=UTF8&ASIN=B00ECTTGFA#R2CBO3XXPIPBNQ gearspace.com/board/newbie-audio-engineering-production-question-zone/1253664-audient-id14-problems.html At one point I wanted to buy an audient interface, but I saw so many bad experiences in users that I preferred to pass on that brand. Not only did it die in a few years or months, but in many cases, parts such as preamps, or outputs, knobs begin to damage, which does not seem to me to be good in such a prestigious brand. And with such good options currently, such as Motu, SSL, and others, it is not mandatory to buy audient. Many times we do not need recent products to have an excellent quality, I did a shootout of several interfaces and my Pod x3 live, to finally realize that the Pod was a better all in one solution. Better DIs guitar tracks, quieter preamps, no latency problem monitoring Vst Amp Sims from the Daw in real time, effects like reverb, delay, chorus of excellent quality. In addition, the noise gate included the best I have tried, it beats a boss noise suppressor and any of Vst that I tried, be it the overloud Th-u, amplitube, Guitar rig, and others, only that noise gate is worth the 200 USD that the Pod costs used.

[@reinulf656]

@@butcher_0392 thank you very much!

[@justicemoody]

Best reviews on the net.

[@zorkname]

Great review, thanks!

[@gammalpojk]

First of all, thanks for all these reviews! Could you make an overall comparison of all the interfaces you've tested? Like you did with the headphone outputs

[@ASOC4]

thanks, after seeing the numbers and graphs I feel like I am finally decided and will go for the ID4 as I need it mainly to mix and master on speakers and 250ohm headphones...

[@robertskrzypiec8583]

Pro reviews, thanks for your jobs.

[@excessivity]

My favorite reviews

[@_dfph]

Thanks for this Julian 😀

[@ksprashutv]

Thanks again for the amazing set of videos. I am trying to find an interface which has the smallest amount of RTL. The HP Output Performance chart that you have is amazing. Do you have a similar chart for the latencies? Comparing best latencies (at lowest possible buffers) and also latencies at a standard buffer setting (say 64 / 128). That'll be super useful, thanks.

[@nicolasarruda6403]

Your videos are awesome!

[@f5770]

Great job as always! And thank you for all the information about the differences between the previous models and also about the converter's names, information that audient didn't want to share. How can you explain the difference between the audient specification A/D dynamic range and your mesurements? Audient claim that its dinamic range is of 120dba 7db more than your measurements, but for the DA converter's dynamic range your measurements are really close to their 126dba

[@RadiAsian]

thank you for the excellent and detailed review

[@KellyAskam_MindExchangeMusic]

All the videos are really great! Thank you for charting this all out. I'd be curious how the newer Motu Ultralight MK5 stacks up against these smaller interfaces. Hope this finds you well. Cheers!

[@Shineva]

hi ) best of the best JULIAN

[@shivambiharimusic]

Top notch content for audiophiles

[@cznielsen1235]

Thank you for the review. On Audients homepage they say that the interface will be able to work just as well using the USB A connection, as long as it is on the 3.0 standard (thus providing 900ma of current). They do say that using USB-C provides extra headroom, but it would be unfortunate if the quality deteriorated significantly when not using this. Did you make sure that you connected to a type A port of the correct type?

[@IngoGarza]

"They do say that using USB-C provides extra headroom, but it would be unfortunate if the quality deteriorated significantly when not using this. Did you make sure that you connected to a type A port of the correct type?" Would like to know this as well. Was about to buy it but when it got to that point of the review I didnt find a reason to continue...Very unfortunate. If the usb 3.1 doesnt do it it's very sad. Dont have a type c ready to go on my build and I would have to customize a lot to make it work.

[@ivayloivanov3744]

@@IngoGarza I have tried with DT 990 PRO (250 ohm) and it worked well with USB A 3.0. In the manual is stated that minimum requirement is 0.9A @ 5V which is at least USB 3.0. And maximum is 1.5A @ 5V which is 3.1 if I am not wrong. On their site is not stated that USB-C provides extra headroom, it's just stated that provides more power. In wikipedia I found this information "USB 3.0 ports may implement other USB specifications for increased power, including the USB Battery Charging Specification for up to 1.5 A or 7.5 W, or, in the case of USB 3.1, the USB Power Delivery Specification for charging the host device up to 100 W". So I am not sure what is going on...

[@BroNapartay]

@@ivayloivanov3744 3.0 is renamed 3.1 with 5V and 0.9A... However, 3.2 is a different beast, as it is at 5V and 1.5A. We really need Usb 4 to come out and clean this mess up. Class C wires are rated to usb 3.2, however C to A wires can also be rated to 3.2 as the generation of USB ports (on both ends) decides the power levels.

[@5apere4ude]

Now, if you check the Tech Specs or the USB port article under FAQ, they do mention it! So, have purchased it? Could it drive your high impedance headphones via USB-A 3.0?

[@mrAxelat]

@@ivayloivanov3744 I am experiencing a lot of distortion with my DT 990 Pros at higher volume - the last 4 volume steps are unusable for me. (Tried this on USB 3.1 A und C ports)

[@CHITRALEKHAGOGOI]

You're the best!!

[@damon_aaron]

It was a pleasant surprise seeing you Warren's channel reviewing the id14. Maybe you can pop up in Podcastage or Booth Junkie?

[@Qaaqqutsiannguaq]

Most honestly reviewer on youtube. Thanks again for good review.

[@pangea2003]

thanks for the accurate review. It would be really nice to watch a review of the presonus quantum line of interfaces from you! :)

[@norbutvstheworld]

I have been building rock solid DAWs for people since 1998. One thing very few people discuss on any of these review channels, is one of the most important to me! And that is, the LATENCY of the product in question. I have not changed my Recording Interface since 2011 because I've not found an interface with better Latency.. I use an ESI 1010e, and recording at 24/96, 32 samples, I get a Latency of 0.500ms. So thanks for the heads up

[@sikwitit773]

It's not the audio interface that's the latency bottleneck, it's the software processing the plugins. A RME HDSPe does exactly what your asking for with 3x' s the samples and faster lower latency I'm talking .96ms PCIe Audio Interface Cards Will be faster than regular audio interfaces because it's the closest thing to the source Mic>preamp(optional) >audio interface> >Cpu Mic>preamp>Cpu/Pcie audio interface card

[@norbutvstheworld]

@@sikwitit773 I'm getting .50ms with my PCIe interface....

[@scooterclarke5800]

Hi Julian. Excellent reviews. Please keep up the good work. Would you please consider reviewing the Arturia Audiofuse Rev 2? Thanks.

[@lekzminuz7435]

Thanks, this video is so awesome! I have the Id4 mkii for recording songs. Its so great!

[@MichaelW.1980]

Thank you so much for the review of these devices! After watching it several times I found it to be very detailed and informative and I got but one question to ask: I wonder, what is „sufficient gain“? You didn’t bring a number. You might want to add that to your pinned comment. :)

[@michaelj.4187]

It will be at the maximum or close to that...as mentioned the gain knob is not linear so therefore experiment for optimum levels...low noise preamps here will drive an sm7b

[@MichaelW.1980]

Probably. Who knows. Usually, it is stated in an actual value on his videos.

[@tejeguitar]

I'd love to see a review of yours of the Apogee Symphony Desktop (just to see how it really compares to the Audients and some other mid-priced interfaces and not just by the price tag and the fame and name behind Apogee).

[@JeffKellyMedia]

Yes please

[@violin-schwerin]

the id4 mkii works wonderfully with Linux. audient really should support Linux more!

[@avpimdb]

Was waiting for this video. Danke! Listening to preamp noises I heard some kind of interference in addition to regular white noise (10:02). Is that just an unlucky catch?

[@JulianKrause]

Hey, I pinned a comment regarding the interference.

[@moppetier]

Hi Julian, thanks for this video. Quite helpful. One question though. Did you test the Audient SONO as well? I know it's aimed at guitarists but if you ignore the two notes section how good are the preamps (both tube and transistor) and the converters in this compared to the ID series?

[@twitchbook-1]

Thanks 👍

[@wokn_nocturama]

Thank you. I would love an rme ou apollo review buy they are really expensive, you do really help for beginners like us to know and understand what we use. Thanks a lot

[@wsnx_]

Nice review, I see a lot of question regarding "MOTU M2 vs. iD14 MKII" and that would be my question too. :D 1. In terms of Mic IN (not important to me because I don't record) 2. Balanced Out (audio quality, especially for users with active speakers) 3. Headphone Out (audio quality, the Audient seems to have more power for headphones which need quite some juice?!?!) Optics are subjective but I think the M2 looks better, which is not that important. :) The MOTU is sold out for quite a while, pretty hard to get your hands on it, M2 and iD14 are now almost the same price.

[@vitisolutions3217]

As always, great review. Any chance you could review the Rodecaster and Zoom Podtrak? Would be great to see a proper review of their performance in the sound chain rather than the ability to play jingles and canned laughter.

[@GreekPcFreak]

hello julian! i found your reviews amusing and so i have subbed.. ever since i was watching you you would kinda like the motu m2, but now i see this id4 mk2 is pretty good too.. wich one would you reccomend for a 120ohms headphones? also the trip latency is so much worse or just a tiny bit vs the motu m2?

[@Joostered]

Time to add some reference measurements in there. How about some RME stuff?

[@TheZeroSbr]

I've been waiting for a Julian Krause RME Babyface Pro FS review for a while myself.

[@reinulf656]

Me too!

[@Duke_Silver]

Great review! Any chance you`ll also review the IK Multimedia AXE I/O ?

[@yvanlegall3531]

yes good idea mr Duke Silver +1

[@mojito6629]

When it comes to low latency RME devices are always on the top list if not the best

[@felixschreiber1786]

14:04 Does anyone know if connecting the interface to a USB-C from a PCI-e expansion card would work? My motherboard doesn't have the connection unfortunately

[@meatball4023]

Did you find a solution or Can you get enough volume with USB A cable to power 250 ohm headphones.

[@landman5294]

Great review, Julian. Can you please review the Arturia Audiofuse?

[@aliozankarci]

Hello thanks for all videos all of them is really excellent can you review zoom h8 as an audio interface , preamp quality or dynamic range etc thank you

[@Caobiita]

Hi, great review. One question, can I with the Audient ID14 MKII control the volume of the monitors and headphones, each one separately? I mean, do the monitors have their own independent volume signal and the headphones have their own independent volume signal? If yes, can the ID4 MKII do this as well? Thank you very much.

[@KindOldRaven]

I'm having a really, really hard time deciding between the iD14 MK2, Motu M2 and 2i2 3rd gen. The latter is by far the cheapest, but seeing as I mostly use 1 mic + headphones/monitors I could also opt for the iD4 MK2, making the Motu m2 the most expensive here. However, combining headphone DAW output + direct monitoring is important as well... man choices...

[@KindOldRaven]

@sYKE What's the points that make you doubt which one to get the most? I'm driving 2 mics (usually not at the same time though; sm58 & at2020), 2 monitors and a set of headphones (usually either a 32ohm or 150 ohm set). Use cases are listening to music, gaming, amateur vocal recordings and the likes. Basically asking for a good all-in-one unit for a penny or two. It's a lot to ask, obviously, but these three all have their pros and cons. Currently trying the 2i2, but the headphone out is a bit disappointing on my 32ohm headphones and it provides just barely enough gain to drive my mics. M2 will have the most gain on tap, more I/O, meters etc. ID4/ID14 MK2 will be the best to drive the 150ohm headphones, but partially rely on software... Hmz... The id4 mk2 is really, really cheap here though. Like 110 or something currently.

[@AndreasHvilhoej]

@sYKE di you guys make a choice? i have the id4 mkII and can't find anything i don't like about it but

[@sikwitit773]

@sYKE motu m2 us is ok u hear lots of people either say its great or it died and has bad customer support while audient mk ii has everything for a home studio/ podcast/ whatever same with the SSL2+ they did a 500 round-trip audio test with SSL2+ and Audient id14 mkii and SSL2+ won, but it's sound seem to be gear towards music production while the Audient is more natural sounding and a speck more clearer sound.

[@emirhanolgun7351]

@@KindOldRaven should you choose the audient or the 2i2 ?

[@xRandomizeTheGame]

what did you end up getting?

[@bastianmaze_beats8730]

Hey! Thanks for all your work. Is there a way to use a load or converter in the headphone output on the interface to decrease the impedance and use cheaper (low ohms) headphones so the frequency response remains unaltered? Thank you.

[@satyambastia2905]

Any solutions?

[@SimplicityForGood]

what mic for singing can work well with this interface? People say the Shure sm7b is too quiet and need a cloud lifter as well to get enough gain... Is that true? people say they set the gain to maximum to hear themselves!? Sounds really bad 🤦🏼and that recommended mic goes for 400-500 euro... but is used by the Swedish public radio here in Stockholm. So a bit confused to how quiet it is and or useful for singers!? seems to also get very expensive if one must add another 150 euro to get gain... 🤷🏼 I want a more vintage look mic for singing and use the iD to an iPad or Mac Mini pro if apple will release that now... and nice silver metallic vintage mic 🎙 you experienced as good for this interface around 300-400 euro? thanks for a great comparison 👍🏻😊

[@gjb7966]

Julian, in terms of overall quality, which one would you suggest: Motu M4 or ID14 mk2?

[@RADERFPV]

If you watch both reviews back to back, it's pretty obvious he prefers the M4 hands down. The part that kills it for the ID14 for me is the lack of a proper mix knob (you have to use the software), and the input meters don't show clipping accurately. The second one isn't that big of a deal, but not having a dedicated mixing knob is :( I can only speak of the M4's quality as I've owned it for a little over a month, and it's top notch for the price. I'm sure the ID14 is great too though, don't think you could go wrong either way.

[@shingngaling4357]

@@RADERFPV you also have a loopback feature on m4

[@petermarch8073]

Loopback on both

[@petermarch8073]

Great review as always. Is it possible to get (FULL) power to the interface without USB c to c, as my computer only has usb a outlet connections

[@uhhkonichiwa...]

Id14 vs MOTU M4 vs ssl2+, please do it,and can we use the Direct monitoring knob in the id14?? In the software??,would love to know your opinion

[@brianbrowning9124]

Yes!

[@MeZenformed]

Maybe throw in the one of the new AU Volt? But either way. Yes!

[@tusharsarmet3771]

Yes

[@phatbasstone]

Great review !!! I enjoyed it and decided to upgrade to the mkii. Between usb A and usb C I’m getting the same headphone volume. Is the difference obvious by ear?? The numbers you’ve posted suggest it’s quite obvious. Thanks

[@MsDream1979]

14:04: it' s possible that this difference was influenced by The quality of the Usb C-A cable? It s a 3.0 certified cable? cable must support 900 mA The USB port was a USB A port 3.0? I m very interessed because my computer has no usb c port.

[@frankluo230]

The big question is id14 II vs SSL2. I really like the build and finish of ID series.

[@michaelj.4187]

I have them both and they are equally good...depends on what you want or workflow needs...

[@frankluo230]

@@michaelj.4187 Thanks heaps for the information. Do you think SSL LED indicator to set the input gain more useful than ID series?

[@michaelj.4187]

@@frankluo230 neither are class-leading but SSL slightly better...

[@MrNickdino]

@@michaelj.4187 which device is class leading?

[@michaelj.4187]

@@MrNickdino - we were discussing led vu meters...in particular between SSL 2 and id14mkii

[@flux6435]

Great video Julian! Very informative. I like to record my guitar directly using amp sims and my DAW. For someone who uses DT 770 250 ohm headphones, would you recommend the ID14 MKII over the Motu M2/M4?

[@gokhantekinmusic]

Hii. Can it drive shure sm7b when we use usb 3.0 (2013 macbook pro). Nice video by the way 👍🏻

[@gastonsantos258]

hi Julian, I have a question. so i'm about to buy the id4 mkii, just to utilize the line input ('cause I'm using external preamp). but in this video, you tell that the id4 having something wrong, that it cannot receive signal more than 14dbv, will it a problem if i'm recording with my external preamp? or should I jst jump to id14

[@Projamusic]

Hi thanks for great video. I have two questions. First: Did you connect the el.guitar to the Di input or to the back line input? When I connect my Gibson Explorer with passive magnets to DI input, the signal clips even when the input gain is turned off. Second: Does Daw report to you that the signal is passing even when your input gain is at zero (turn off)? When I connect the mic At4050 and Bass Guitar with passive magnets, the signal passes up to -24dbFS in DAW and on LED meters.

[@atarkam8232]

THANK YOU, really. i was looking for an interface for a 470 ohms headset, and it's so hard to find those stats.

[@zinhosalaverry8294]

Great video man! I have a question. I’m thinking about upgrade my home studio with a new audio interface (I have the behringer umc22) and I was thinking about the ssl2+ and the audient id14. Wich one would you recomend me? I’m a guitar player and I need a good preamp and noiseless audio interface. Thanks!

[@butcher_0392]

The truth is, any current low-cost interface will serve you well to record your guitar tracks with very good quality. You should not be obsessed with that, not every year or 2, be trying to upgrade your equipment. Guitarists in particular, we are being deceived all the time with many lies, they make us buy products that we do not need such as: 1) Neural DSP Plugins 2) Kemper, Axe FX lll or Helix 3) Fishman Pickups, interfaces, and other crap. You just need to learn what you can about production and mixing, that's what makes the difference between a professional guitar tone and a shitty one. If you know what you do, you can achieve the same or better results than a Kemper, with free amp sims. If you still want one of the best options for tracking guitar DIs, you can buy the Pod X3 Live and use it as an interface, that is useful for Monitoring from the Daw Vst in real time, without any latency problem. Its preamps are super quiet, tight low end, crisp mids and clear highs.

[@ChakrabortyRaja]

Hi sir, guide me on thing. I have bought Audient Id14 mkii, recently. My new ID14 is releasing so much heat. Before this I have used focusrite 2i2. It wasn't released that much heat. Please help me.

[@RyanWreckcrow]

Nice video! Just a quick question: You mentioned the lack of imput meters and clipping indicator, but can you check that with the software they provide?

[@perfectalpha]

If you have the ID software up, yes you can see the levels digitally.

[@mattiacenacchi726]

I HAVE IT , JUST BUY IT , FOR REAL.

[@hericpan5442]

Great review! Thanks a lot! I'm currently using id4mkii to drive my HD800s and it's working fine. I was wondering whether should I upgrade to apogee duet 2 (3's specs degraded) or spl phonitor. And I found out it's not a huge difference/upgrade from id4mkii according to my current needs.

[@martineden5197]

Nice channel