Auto Changeover Switch (ATS) Wiring! Double Power Automatic Transfer Switch Wiring

[@gadgetfreak786]

Thank you! Very clear instructions. Got mine working with your demonstration

[@kabandajamir9844]

The world's best teacher thanks sir

[@edgarlepiten2883]

Thanks for this video. Clear and precise. Kudos!

[@samanthak.b.g6175]

Thank you very much for your explaining....

[@geeverjob9661]

Can it use as change over switch for solar and grid

[@electricwiringcenter1365]

Yes

[@geeverjob9661]

Buying link please

[@cdp029]

Thanks, excellent video.

[@mohamedsiddik0]

Thanks for your video, Can you please give some details about control terminals in ATS

[@kabandajamir9844]

So nice thanks sir

[@bakergenius]

I it possible to use ATS for DC power?

[@SilverMiraii]

Can this type of ATS send a signal to the generator to make it start ?

[@dileep3018]

Can we use this for inverter vs grid

[@roblatour3511]

how do you deal with the ground connections from all three?

[@hosabettulaxmanbangera1471]

Thanks Indeed.

[@jack69457]

Thank. I have done all the connections properly. How do I connect it to the DB box?

[@adebiyiadedokun4663]

The fan serves as your DB in the illustration

[@jorgeluisvelazquezgonzalez4032]

Hello, I have a 220V 63A 2P ATS, similar to the one you explain, but it does not want to recognize a 120V power supply on the main line, only 220V gives the ready, the backup power supply works perfectly, but the main one does not work automatically since it does not give the ready or the second signal in the switch, could you tell me what I should do, the connection is fine, only that being 120V (1 phase + 1 neutral) it does not transfer, and I must close it manually and it only signals voltage, not ready-closed position, what should I do, would you help me?

[@montejaydon5415]

Can timer relay wired to this type of transfer switch

[@mimobyle398]

What about wiring of top green slots?

[@expjw]

Can this device accept both 12v DC power supply as well as 110v-240v AC power supply?

[@MonroweToussaint-gr4gb]

Where is the signal/ communication cable that runs from the change over switch to the generator to start the generator when electricity goes out?

[@gl0wbot768]

Amazing

[@TahirHussain-du8kk]

Where to buy???

[@dancehallexposed6193]

My question is, the N side of my switch the UN light is on but the NON light is not and when i turn on my generator the R side both lights are on but on the N side only one and it hum like hell, what is the cause of this please.

[@jorgeluisvelazquezgonzalez4032]

The same thing happens to me, did you find a solution?

[@dancehallexposed6193]

@@jorgeluisvelazquezgonzalez4032 I JUST CHANGED it to the manual, could'nt be bothered.

[@jorgeluisvelazquezgonzalez4032]

@@dancehallexposed6193 I have already managed to make it work, feeding through the main network with 220v, that is, two phases and at the output it only took one phase, it was working perfectly but now it does not make the transfer to the reserve that I feed with a solar system, it does change from the reserve to the main one but not vice versa

[@dancehallexposed6193]

@@jorgeluisvelazquezgonzalez4032 thanks for the information, found out my house is wired in 120v and i was using a 240v device.

[@vijaymandavilli8258]

Where can we get this

[@brotheradam]

so, if I want to create an automatic system that goes from Mains to Generator to Solar automatically I need two of these switches then?

[@raghavshakya8196]

Hello .. kaha se milega ye

[@SiddalligaswamySiddalligas-q5l]

ಇದರ ಬೆಲೆ ಎಷ್ಟು

[@motor3355]

соплай соплай соплай

[@mampekheswa6707]

How much is it