I had a MOFSET IRF520 in my Arduino starter kit. Tried it and it worked. It will not work with BC547 transistor. I wasted some time with other KZbin videos that were fake and did not work. Thanks for your great video.
@sm_electronics5 ай бұрын
thanks...
@thanxred412610 ай бұрын
how can i revers it... ... i want light on when is light an d light out when is dark
@sm_electronics10 ай бұрын
change the position of ldr and 100k
@franciscofortunato1864 Жыл бұрын
Super idea!
@SameerAwan-g8v6 ай бұрын
Feak😅
@aranyabiswas41032 ай бұрын
Can i use it 24/7 for my 12v Street lights?
@mehmetkasmTB3DKM11 ай бұрын
Rezinstans 1m super no problem
@SujataBharati-ir9xd12 күн бұрын
Sir can i use F12C20 mispad please reply my brother❤❤❤🎉🎉🎉🎉🎉🎉plz plz plz plz plz❤❤❤please reply tomorrow is my science exibition please😢😢😢😢😢😢😢😢🎉🎉🎉❤❤❤and can i connect 4 pic 3 volt led❤❤ instead of 12 volt led please reply❤❤❤🎉🎉🎉🎉🎉🎉plz i request you plz🎉🎉🎉🎉❤❤❤❤😢😢😢😢plz my brother
@sm_electronics11 күн бұрын
@@SujataBharati-ir9xd no. use any MOSFET.
@mairajansari88064 ай бұрын
What is the maximum ampere load can be connected?
@sm_electronics4 ай бұрын
49 Amps.
@rkmusic5687 Жыл бұрын
Sir irf44n ke dusra MOSFET le sakte hai please reply 55nf06 le sakte hai
@sm_electronics Жыл бұрын
yes
@sm_electronics Жыл бұрын
Yes,you can use
@XXX-x7b4g21 күн бұрын
සුපිරියට වැඩ....👍👍👍👍
@MindLoveDiariesАй бұрын
Can i Use bc547
@sm_electronicsАй бұрын
use MOSFET
@yuzupiku201010 ай бұрын
Sir lekin led bulb 5 ya 10 minutes salne par hi bohot jyada heat hota hey kyu sir...
@sm_electronics10 ай бұрын
led per 2.2ohm 1w resistance lagao.
@wolffengineering70386 ай бұрын
Does the wattage rating of the resistor need to match the load of LED’s in this circuit?
@sm_electronics6 ай бұрын
no
@astronic452210 ай бұрын
Nice roject brothers👍🔔🙏 2:37
@sm_electronics10 ай бұрын
thanks...
@kocherlashivakumar12086 ай бұрын
Its working yaaa just now trail complete
@sm_electronics6 ай бұрын
advance version kzbin.info/www/bejne/apupioSMrJqEjas
@khaqanabbas8055 Жыл бұрын
Can i use p60nf06 instead irfz44n mosfet?
@sm_electronics Жыл бұрын
yes
@khaqanabbas8055 Жыл бұрын
Thanks bro may God give you more and get successful in future.
@hiranukwatta7076 Жыл бұрын
can you put video of 12v solar power recharjable light diagram
@sm_electronics Жыл бұрын
I Will try...
@VesExcYohannes2 жыл бұрын
I have a 3w 12v led cob. Then how much resistors to use?
@sm_electronics2 жыл бұрын
Use low resistance 2.2 ohm or 1 ohm for safety.
@gohyanqing61716 ай бұрын
Hi sir for the battery 12v is it need to use alkaline battery?
@sm_electronics6 ай бұрын
any type of battery can be used. lead acid, lithium or alkaline battery can be used.
@mehtagautammahraj2328 Жыл бұрын
Ont good 😢😢
@md.fariyad9745 Жыл бұрын
Kindly make one 3.7 volts circuit for 2 leds 5mm
@sm_electronics Жыл бұрын
kzbin.info/www/bejne/jJDRZGetoLSBqs0
@creativelovestatus6981 Жыл бұрын
Sir ckt diagram 🤔
@yagyaveersingh39932 ай бұрын
There is not need of any circuit follow the video steps to make it easily...
@miakhalifa13288 ай бұрын
Can it work with 9V battery?
@sm_electronics8 ай бұрын
yes...
@faqihahady313 Жыл бұрын
if I supply 12v energy, then I only use 3 12v LEDs, how many reresistors should I use, thank you please answer me...
@sm_electronics Жыл бұрын
If you use 12v led no resistor is needed.
@faqihahady313 Жыл бұрын
@@sm_electronics so i don't use resistor also it's ok?
@faqihahady313 Жыл бұрын
Actually like this, , I have followed the example in your video, I have also prepared the materials, such as resistors, irfz44n, and LDR sensors, led, but the end result is not like yours, if I LDR it doesn't work a bit, even though I gave it the light is strong, the light doesn't want to turn off, it's still on but dim,
@faqihahady313 Жыл бұрын
So the LED light is not 100% off even though it has been given strong light
@sm_electronics Жыл бұрын
Ldr is getting reflected light.cover the ldr
@athurein264 ай бұрын
I have one, which is not switched off but only dimmed. But if I closed it near the bulb, it's totally switched off. Can I increase or decrease (100k) resistor? Or what can I do? You used 100 k resistor, isn't it?
@sm_electronics4 ай бұрын
experiment with different values. you should increase the value to 220k or 330k . if it doesn't work try to decrease the value use 47k or 33k or 10k instead of 100k.
@athurein264 ай бұрын
@@sm_electronics thank you, I changed with 150 k. I will test it tomorrow
@athurein264 ай бұрын
@@sm_electronics I think, if I add 100k ( pre-set) variable resistor, will be fine
@sm_electronics4 ай бұрын
let me know...
@athurein264 ай бұрын
@@sm_electronics I will test it tomorrow
@dj_sorra8605 Жыл бұрын
Whit 5v led and 5v battery is the same?
@sm_electronics Жыл бұрын
Yes you can use
@parthrajsinhkasela3298 ай бұрын
It's working 😂😂😂😂😂
@sm_electronics8 ай бұрын
nice...
@miguelvicentec9 ай бұрын
how should i do in order to connect the circuit to the switchboard instead of directly to the light i want to control?
@sm_electronics9 ай бұрын
kzbin.info/www/bejne/kIXNoXauabmcqZY
@miguelvicentec9 ай бұрын
@@sm_electronics but its a 12V switchboard, on a sailboat, are the components still compatible or shoud something be different?
@mariokaram91142 жыл бұрын
It's same resistor for 4 v circuit?
@sm_electronics2 жыл бұрын
Yes
@yuzupiku201011 ай бұрын
Mey ne banaya hai lekin Bohot jyada rashni Ldr par parne se hi light off hoti kam rashni mey nhi kyu...?
@sm_electronics11 ай бұрын
100K ki value jyada karo. 200k or 330k or 470k lagao. problem hua to comment karna.
@yuzupiku201011 ай бұрын
@@sm_electronics okk thank you mey try karta hu okk thanks sir
@yuzupiku201010 ай бұрын
Ho gaya sir thank you very much 😊😊 keep it up sir thank you for for helping me
@yuzupiku201010 ай бұрын
Sir lekin led bulb 5 ya 10 minutes salne par hi bohot jyada heat hota hey kyu sir...
@Rawalpindiii9 ай бұрын
@@yuzupiku2010 resistor lagao
@haktun83516 ай бұрын
Bol bol Dua edin Hintlilere onlarin sayesinde bir seyler ögreniyorsunuz
@sm_electronics6 ай бұрын
thanks...
@miteshdhanani Жыл бұрын
Want to connect it with a solar panel to charge the battery then send a message
@sm_electronics Жыл бұрын
how old are you?
@miteshdhanani Жыл бұрын
Thks r there any changes
@miteshdhanani Жыл бұрын
I am 50yrs
@ThathsaraBandara-yc1vv Жыл бұрын
It's working...
@sm_electronics Жыл бұрын
welcome 😃
@bineeshmadhu16952 жыл бұрын
Did u connect with 12 v dc battery??
@sm_electronics2 жыл бұрын
Yes
@mahirakidskereatif6 ай бұрын
inverse, the lamp is bright while sun raises
@sm_electronics6 ай бұрын
change the position of 100k and ldr
@mahirakidskereatif6 ай бұрын
@@sm_electronics the light is of
@sm_electronics6 ай бұрын
give more light
@ethicalhacker1 Жыл бұрын
How can i add a pir motion sensor to this circuit...?
@sm_electronics Жыл бұрын
for what?
@ethicalhacker1 Жыл бұрын
@@sm_electronics for an under bed lighting that lights up at night everytime someone gets down from the bed and turns off automatically after they get back into bed...
@sm_electronics Жыл бұрын
@@ethicalhacker1 search pir motion sensor project on KZbin
@gibintjose8 ай бұрын
Your resister 1m ohms ???
@sm_electronics8 ай бұрын
100k
@sm_electronics8 ай бұрын
brown black yellow
@RajKrishnaBhunia Жыл бұрын
Not working
@sm_electronics Жыл бұрын
check the connection.
@ghulammohiodin1514 Жыл бұрын
Good idea i will try...i have one question plz. Is it sensitive like in the dark only its work and also what is the battery consumption?
@sm_electronics Жыл бұрын
It is enough sensitive. the battery consumption is depends on the number of LEDs you are driving. Be Happy 😊😊😊
@ghulammohiodin1514 Жыл бұрын
Thanka for reply. As per this circut which led you recmend? I am new one in this field with less knowldge. Plz guide me for good back up. I have 12 volt with 6 batteries lethium battery with 3s bms
@sm_electronics Жыл бұрын
use available 12v led
@KnightTamila6 ай бұрын
220 v supply?@@sm_electronics
@sm_electronics6 ай бұрын
no
@Mradi471 Жыл бұрын
Hi,bhai kya mai is circuit ke sath aik 5w 5ohm ka resister laga sakta hoon? us se light hot nahi hogi answer me please I'm very worried about that
@sm_electronics Жыл бұрын
yes bhai . very good idea
@Mradi471 Жыл бұрын
OMG THANK YOU SO MUCH BRO
@Mradi471 Жыл бұрын
Or Kya mai 1/2w 100k ohm resister ki jagah 1/4w 100ohm resister laga Sakta hoon?
@sm_electronics Жыл бұрын
10k se jyada value lagao
@verenkaraatish6572 Жыл бұрын
Can i use bc547? For 12v strip?
@sm_electronics Жыл бұрын
no, very low current.
@verenkaraatish6572 Жыл бұрын
Which one can I use?
@sm_electronics Жыл бұрын
use any mosfet
@verenkaraatish6572 Жыл бұрын
Not a specific one?becoz I don't have the one that u used
@sm_electronics Жыл бұрын
search the mosfet name in Google
@roamingwithapurbo2 жыл бұрын
thank you. it works. but i want full bright with 4 volt circuit. what should i do ?
@sm_electronics2 жыл бұрын
It should give full brightness at 4v. If not reduce 100k.
@roamingwithapurbo2 жыл бұрын
@@sm_electronics same circuit doesn't work with 4 volt. then should i remove the 100k resistance? you mean using without any resistance?
@sm_electronics2 жыл бұрын
Use 10k to 22k instead of 100k. What volt led are you using?
@roamingwithapurbo2 жыл бұрын
@@sm_electronics 4 volt 5 watt
@roamingwithapurbo2 жыл бұрын
@@sm_electronics i used 10 k. but still not working
@Abhi_gaming_official_997 ай бұрын
Hi brother circuit kaha milege ❤😢
@sm_electronics7 ай бұрын
video thumbnail
@Abhi_gaming_official_996 ай бұрын
@@sm_electronics link dalo bhaiya ❤
@linhkien19022 жыл бұрын
mạch cảm biến ánh sáng bằng năng lượng mặt trời 👍👍👏🏳️🌈
@RohitKumar-ws7zb2 жыл бұрын
Sir not working
@sm_electronics2 жыл бұрын
It is a working circuit.
@wazintonestrela6936 Жыл бұрын
Como você faria um sistema onde na presença da luz o sistema iria funcionar?
@RanubNas-ie3lp Жыл бұрын
Perfect
@sm_electronics Жыл бұрын
thanks
@sm_electronics Жыл бұрын
thanks
@pm764 Жыл бұрын
how calculate resistor value for 24v input please
@sm_electronics Жыл бұрын
Use 220k
@kennethcoutinho4439 Жыл бұрын
Nice but irritating music
@sm_electronics Жыл бұрын
thanks for pointing out...
@HeriAcay-mf3bw Жыл бұрын
Good
@sm_electronics Жыл бұрын
Thanks
@RohitKumar-ws7zb2 жыл бұрын
Ye tej jalegi aur ye 4 volt par kaam karga
@sm_electronics2 жыл бұрын
Yes...
@RohitKumar-ws7zb2 жыл бұрын
@@sm_electronics ty so much sir
@lasseblow2 жыл бұрын
How long LED strip can this circuit handle...?
@sm_electronics2 жыл бұрын
IRFZ44N is a N-channel MOSFET with a high drain current of 49A,so very long strip.
@lasseblow2 жыл бұрын
@@sm_electronics what size is the LDR...?
@sm_electronics2 жыл бұрын
Any size
@lasseblow2 жыл бұрын
@@sm_electronics. So the resistance of the LDR doesn't have any relevance, is that correct..?🙂