Automatic reverse forward wiring of VFD using sensors| vfd reverse forward wiring using sensors |

🙏sorry friends there is a mistake in this drawing🙏-push button ko input positive wire se nai negative wire se dena hai..
--mai wiring diagram dala hai community me,,aur yaha description me v
follow that.
--stop push button input wire will be zero volt not 24 volt.
wiring diagram-
imgur.com/gallery/qlrAdWk
Automatic reverse forward panel wiring using limit switch.
• Automatic reverse forw...
Automatic reverse forward of VfD using sensors
Automatic reverse forward control wiring using sensors
Automatic reverse forward panel control wiring using sensors
Automatic reverse forward run of motor using vfd and sensors
Motor ko reverse forward me kaise chalu kare automatically sensors se.
Motor automatic reverse forward run using sensors
Automatic up down of motor using sensors and vfd
Automatic reverse forward of motor
Automatic reverse forward starter
Automatic up down application wiring
VFd reverse forward wiring
Delta vfd reverse forward connection
Npn no sensors wiring
Npn Pnp sensors connection
Paper cutting machine wiring
#automatic #reverse #forward
Relay holding
• Relay Holding circuit ...
Solid state relay holding
• Solid state Relay Hold...
Auto reverse forward with sensors
• Automatic reverse forw...
Inching and holding of contactor
• Inching(jog) & Holding...
Auto transformer starter control wiring
• Auto Transformer Start...
2 floor lift wiring animation video
• Video
Gate open close wiring
• GATE system control & ...
Pump motor and float switch wiring
• Pump motor wiring with...
Compressor pressure switch wiring star delta starter
• Compressor pressure sw...
Compressor pressure switch wiring
• Compressor starter wir...
3 floor lift wiring simulator video
• 3 floor lift (elevator...
Delta vfd f parameter setting
• Delta vfd F parameter ...
Delta vfd f control and power wiring
• Delta vfd-F full detai...
What is maximum demand md
• What is Maximum Demand...
Multiplication factor
• What is MULTIPLICATION...
Counter meter connection with sensors
• Counter Meter connecti...
Check sensors is npn or pnp
• How to check sensor is...
Delta vfd run using push button
• Delta-M VFD start stop...

[@PEARLENGINEERING1]

🙏sorry there is a mistake here- Stop push button ko input negative (zero) volt dena hai..maine yaha galti se positive de dia hai

[@PEARLENGINEERING1]

Follow this wiring diagram imgur.com/gallery/qlrAdWk

[@dildartechnician3420]

Sir stop star switch hai reverse switch nahi deya kune

[@dildartechnician3420]

Sir is tra Jo cooler me lift waly system be banaye 4 Puch switch 4 limit switch ke cooler NO NC krwa dy samj aye gai please

[@PEARLENGINEERING1]

Ye automatic reverse forward hoga ek bar on hone ke bad sensors se

[@RakeshKumar-fz3fr]

Sir, may I use D700 DRIVE IN THIS FUNCTION.

[@omkarchauhan5392]

Samjhane ka tarika bhut hi acha hai sir aapaka 🙏🙏 Thank sir Cautious sir 👍👍

[@abhijitbhujel1418]

Thanks for very valuable knowledge giving.

[@manjunathamanju6204]

Thank you so much your explanation 👍🏼👌🏽🙏🏽

[@kuldeepmaheta3684]

So underrated channel.. Good work sir. 🙌

[@PEARLENGINEERING1]

Thank you

[@ksg802]

Very very clear teaching

[@chaudharykaif]

बहुत गुड सर जी

[@shravanyadav395]

Very halful video sir 🙏🙏🙏

[@mrhacker9117]

On off push button ko nagitive Sy jorna hai apny positive Sy jorna Howa hai

[@dastechnicalchannel5232]

Sar ji aise hi banaa kar dikhaiye diagram (g plus 2 ka) tabhi samajh mein aaega

[@PEARLENGINEERING1]

Bhai...lift ka video maine keval business purpose ke lie banaya hai...

[@manjaljeet8686]

thanks from in Nepal सर practical तो देख्नै परेगा। एसे तरिकासे कोहि भि perfect नहि होगा।

[@PEARLENGINEERING1]

Ye video dekho kzbin.info/www/bejne/hmHVgqWLl5x9qZo

[@sanjaysen6939]

Thanks sir

[@aungoo3757]

Sir....Please explain the control diagram next video lecture because of language problem Always Respect

[@SureshSingh-jd8qd]

To good sir

[@sunilt1016]

Forwardvnot holding

[@omprakashsharma5210]

Daut senssar relay se F R relay ke interlocking tak hai sir.

[@masruk423]

Thank you . dada i want to VFD autamatic Reverse and Forward with limit switch?

[@joyram2439]

Counter meter kiboard with VFD motor automatic rebars foroad connection daigram video sir

[@manukumar5640]

Super

[@friends-ev4ch]

it is indicating private videos in given discription link videos

[@empty_rider925]

Brother any program control

[@user-lt9yi2ef6y]

Osam

[@sanjaysen6939]

🙏🏽🙏🏽🙏🏽🙏🏽

[@sanjaysen6939]

🙏🏽🙏🏽🙏🏽

[@sanumandal9228]

Please show the drawing Frist then it is easy for understanding

[@PEARLENGINEERING1]

Ok

[@user-sg4kw9di6g]

Sir push button no aur nc sensor laga kar vfd me kis tarh kiya jayga

[@praveenkumar-uu6ht]

Sir pls explain behind the reasion of why we connected wire that place like no or nc or a1 a2

[@PEARLENGINEERING1]

No and nc are used for interlocking as required by system,,and a1 and a2 is coil connection of contactor and relay..when we will give coil voltage then contactor or relay will operate

[@mrhacker9117]

Dear Sir Relay s1 or s2 ko native senser Sy mil Rahi hai or reverse or forward rely ko nagitive Kahan Sy mil Rahi hai ?

[@bobysaini8120]

Smps se fwd or rsv ko negative mil ra h

[@PEARLENGINEERING1]

Mera pin kia hua comment dekho aap

[@omprakashsharma5210]

Shckrin short lene ke Lia mauka diya Karo sir.

[@PEARLENGINEERING1]

Haha..

[@ManiSabari-sf1yo]

Confiue slowly vidoe tk

[@vijayojha3280]

हेवी tork सेटिंग बताओ

[@SaifulIslam-vs1tt]

Sir.. Motor winding machine Banana. Auto matic. Kitana amaound lagaga. Apka pass Malaga.

[@PEARLENGINEERING1]

Ha mai iska panel ban sakta hu..contact here 7600382705

[@swarnjitkaur5695]

MCT 10 Sat up software download kesse kra sir

[@felixoladapo4051]

Can you explain in English

[@omkardeshkar4725]

What if machine stops in between due to power failure??? How can cycle be start after power recovery?

[@PEARLENGINEERING1]

After power resume,when start the machine and it will move in forward direction always

[@SuhailKhan-fh9re]

Ydi hme motar ko rewards me 50 hz chalana hai aur forward me 15 hz chalana hai to delta vfd el 2 hp 3 phase me kon sa parameters set kre

[@PEARLENGINEERING1]

Use double speed wiring of vfd

[@rajahuja6287]

Kya vfd mai motor ke speed forward mai high reverse mai slow kar saktay hai

[@PEARLENGINEERING1]

Use 2nd speed of vfd,and use contactor for 2nd speed and reverse the phase sequence

[@rajahuja6287]

@@PEARLENGINEERING1 okay,I will try.

[@dastechnicalchannel5232]

Only 3 relay 2 contactor se 3 floor ka lift chal raha hai three piece limit laga hua simple circuit hai kaise banate hai mujhe pata nahin maine dekha he lakin samajh me nhi aie video bana ka dekhie sir

[@PEARLENGINEERING1]

Okk...aisa karo na aap,uska wiring diagram bana sakte ho ,,wire ko dekh dekh ke to ,mujhe bhejo.mai bana dunga

[@laxminarayanmohanty9795]

Why you give 24v A1 & A2 in reverse relay

[@PEARLENGINEERING1]

Watch my latest video of automatic reverse forward with only 2 relay

[@jobsinpakandgulf621]

Really k coil ko negative n dya

[@dildartechnician3420]

Sir this software name version please details

[@vikasjaat7153]

Sir diagram send ker sakte ho iska

[@Ankit_yadav229]

Sir vfd of denser Sense and port and key pad for run ha

[@PEARLENGINEERING1]

Didn't understand?

[@vijaysolanki5267]

Sir high and low level switch se tank is level kese control kare uska writing kese ksre

[@PEARLENGINEERING1]

Ye video dekho kzbin.info/www/bejne/i5ymZIqVodV7rrM

[@nabinpaul4262]

Sir reverse speed and forward speed ka different kysa kare

[@PEARLENGINEERING1]

Rev forward me to mere ko idea nai hai different speed ka..tum double speed use karo with different Frequency, aur jab v dusre speed ka command do to usse ek dusra contactor on karao aur drive ka output pahse sequence change karke is contactor pe de do..jise ek bar motor forward aur ek bar reverse me ghumega wo v alag speed me

[@VirendraKumar-ic1hy]

Sir ji namaskar 🌹 Drive jub run condition me rahta hai to (u v w )me output voltage multimeter me show nahi karta .kyu.

[@PEARLENGINEERING1]

Multimeter se vfd ka output voltage nai check kar sakte hai..ampere check karo clampmeter se..use motor ka performance pata chal jaega..voltage check karne ke lie alag device hota hai..

[@anildarri2185]

Sir ek confusion hai sensor sens kiya to output realy me aaya aur contractor on hone se drive ke thought motor forward me run krne LGA . But sensor ke samane target hat jata hai to sensor ka output bhi dena band ho jata hoga to continue forward contractor kaise on rhta hoga ...isme holding ke bare me kuch bataye nhi nhi ...pls reply confusion me hu Thora.

[@PEARLENGINEERING1]

Dhyan se dekho..holding circuit banaya hai..air bataya v hai

[@anildarri2185]

@@PEARLENGINEERING1 yes

[@khalipili2200]

Sir push batten 0v jana tha realyo coil comen 24a1 de diya tha rakha tha relye a2 mein bhi 24 v waring galt hai sir a1 rdv frd mein 0v comman dena tha

[@PEARLENGINEERING1]

Thank you bhai..push buttons ko input zero volt dena tha..galti se. Positive de dia hai

[@ksg802]

Sir maan lete hai ki mere paas do motor hai . Motor 1 push buton press karte hi run hota hai aur dus round par stop hota hai aur counter ke counting complet hone par output NO par aa jata hai aur us output ke dwara mera motor 2 run hota hai jisme ki ek pulley laga hai aur usko limit switch se rokte hai . Jab limit switch puley ke dwara press hota hai to woh no ban jata hai Magar sir fir se wahi process repeat karne ke liye jab mai push button press karta hu to motor 2 kaise run hoga q ki woh limit switch ke no banane se supply ruka hua hai.

[@ksg802]

Sir is par ek video banaye

[@PEARLENGINEERING1]

Thik hai

[@ksg802]

Sir i m yr subscriber .sir aap reply jo karte hai bahut achha lagta hai.aap sabhi ko reply karte hai ye achhi baat hai

[@abdulwahabkheruwala2575]

Can u please share the wiring diagram

[@PEARLENGINEERING1]

Wiring diagram is in commmunity post and also in description

[@abdulwahabkheruwala2575]

Will this circuit work same in case of stepper motor

[@PEARLENGINEERING1]

For stepper motor you have to use stepper motor drive ...and wiring according to that drive

[@PEARLENGINEERING1]

Automatic reverse forward using sensors and 2 relay kzbin.info/www/bejne/Z6W7pIyJpd6Fj7c

[@Faqir712]

Sir BMU machine control wiring diagram

[@PEARLENGINEERING1]

If you have electrical drawing send me..i will make a video on that..because i dnt know the working logic of bmu..

[@Faqir712]

@@PEARLENGINEERING1 how to send diagram you

[@PEARLENGINEERING1]

[e-mail]

[@sksharma9137]

It is wrong brother, after stopping it starts even after sensor sensing. when it should not happen

[@PrakashKumar-oy5nq]

Sar mujhe sahi se samjh nahi aaya

[@minttimyvlogs5933]

Apne non bol kr position suply diya hai sense me

[@PEARLENGINEERING1]

Jo galti hai..wo maine description me aur comment me explain kia hua hai..

[@yaseenshah7465]

Bahi galti kar di hy AP ney

[@rajeshkumarpati153]

Rung worring

[@ramavadhnishad1812]

wrong

[@PEARLENGINEERING1]

🙏sorry there is a mistake here- Stop push button ko input negative (zero) volt dena hai..maine yaha galti se positive de dia hai

[@adarshdubey62]

koe bhi relay hota hai jab tak hm com point par supply nhi dege to hme out out put nc or no nhi melega or bhai tum to direct he relay se nc, no se supply out put karwa de rhe ho 🤣🤣🤣🤣👎👎

[@minttimyvlogs5933]

Rong wiring