Great video and explanation! Now I can’t wait until my next misfire comes in so I can put these skills to the test! Thanks!!
@nirbhay.8400k2 жыл бұрын
Thanks a lot for this video! Was very helpful and was exactly what I was looking for.
@8power03 жыл бұрын
I MUST GO OVER THIS ONE AGAIN, THIS ONE IS A LITTLE HARDER TO RAP MY HEAD AROUND THEN THE REST OF THEM . BUT IT GOES TO SHOW WE ARE DEFINITELY LEARNING AS YOU GO. PLEASE KEEP UP THIS GREAT WORK CAN'T SAY ENOUGH GOOD THINGS ABOUT YOU AND THIS VIDEO SERIES !!!!!!!!!!!!!!!!
@ThePracticalMechanic3 жыл бұрын
Let me know if you run into any trouble or if you want me to cover the electrical portion in more detail.
@billyyoder81713 жыл бұрын
Thank you Chad and Val. Good job. Have a blessed and safe week to you and your family. Merry Christmas.
@ThePracticalMechanic3 жыл бұрын
Thank you Billy, We hope you and your family have a blessed holiday as well.
@spelunkerd3 жыл бұрын
When fiddling with these i thought I was doing something wrong, my secondary wire patterns were much harder to quantify in the way as old style systems. So it is reassuring to see you encounter the same issues. Thanks for going through this series, it clarified many issues for me.
@andrewk7783 жыл бұрын
I use a General Technologies Corp. GTC-505 with great results. I rarely see it in videos. Thank you for sharing.
@ThePracticalMechanic3 жыл бұрын
Your right, I have only seen a few videos on it as well. It looks like a great tool.
@gabiladarlington14569 ай бұрын
Best video ever on this topic
@Lambros_Stefaneas3 жыл бұрын
well done. thanks for sharing your knowledge. looking forward for your next video.
@ThePracticalMechanic3 жыл бұрын
Thanks for watching!
@ThunderbirdRocket Жыл бұрын
Excellent presentation !
@johnwebb91763 жыл бұрын
Great video, I like the illustration. I missed week 10 but I still intend to do it at some point. This video definitely helps with the explanation of secondary vs primary and the difference between COP's and old school. Thanks again man, appreciate ya taking the time to do this video set. I was gonna ask where you got that extension cord but you linked it, gonna get me one by the end of the week hopefully.
@70corwin Жыл бұрын
snapon COP -11 works good on capturing waveforms especially on the heavily insulated coils. It has some kind of amplifier built in or something?
@MaicSalazarDiagnostics3 жыл бұрын
Great video Chad, I like to re inforce knowledge.
@ThePracticalMechanic3 жыл бұрын
Thank you Maic. Have a great holiday.
@dalenassar91526 ай бұрын
GREAT VIDEO!!! I actually need to have a signal that indicates when the spark is fired (or actually present) for a special project. I must use the wires already on the COP. I am able to trigger my circuit on the rising or falling edge of IGT or IGF...any suggestions?? I will be ready to try it in a few days. BTW: Have you ever 'scoped' a logic signal that was actually 12v logic instead of 5v?? THANKS MUCH!!!
@mike-yp1uk Жыл бұрын
Great video not alot to see as far as other coils.
@briansilva912010 ай бұрын
Hi, great videos and thank you for all your hard work, however the Facebook group I can’t seem to find it with the link shared down below as you mention.
@ThePracticalMechanic10 ай бұрын
We have closed the group for now but may reopen the group after the new year and if we are lucky we will have a season 2 of the automotive weekly waveform.
@vickenkaragozian20413 жыл бұрын
Hi Chad. Can you show us Toyota ignition coil that prevents the vehicle from starting even though we have IGF signal when cranking. I have found that we also have IGT signal but vehicle starts & dies, I have found the ignitions coils put high amperage during cranking & prevents vehicle from starting. I know if we have shorted ignition coil it will make the 5v from igf to go down to zero volts but i have seen shorted coils & still have good IGT & IGF signals.Can you show us some waveforms with no starting situation? Thank yoiu
@georgebonney903 жыл бұрын
thank u sir👍
@ThePracticalMechanic3 жыл бұрын
Most welcome
@rubensalgado13983 жыл бұрын
Still want to do distributor but might take awhile since all we get is newer cars😆
@ThePracticalMechanic3 жыл бұрын
I feel like distributor waveform offer the ease of access required while learning the waveforms. Makes it easier to create your own problems so you can see the effect on the scope