Autonics Tutorial : Temperature Controllers TZN / TZ Series

[@hegyeim1365]

Voltage input has been set At 1:53. But the input type is a K-type element. Isn't it?

[@AutonicsCorp]

Thanks for your comment. You are right. We created the situation for voltage input. It is just an example.

[@cakadd1021]

Excuse me sir, I have a problem setting the temperature controller parameter, i want to the temperature controller Autonics TZN4S can give the analog signal (for example 0°C - 100°C = DC 4-20 mA) , i have done setting the parameter like in the manual book, but the temperature controller can't out the analog signal. can you help me, please?

[@AutonicsCorp]

If the 4-20mA you mentioned is the transmission output, it is not supported by TZN4S. (For the purpose of transmitting the measured temperature value to other controllers) Please review the product with transmission output function. Thank you.

[@cakadd1021]

@@AutonicsCorp can you tell me what autonics temperature controller supports analog output to send signal to PLC?

[@AutonicsCorp]

If you want the same size product, TK4S-R4□□ or TK4S-A4□□ is suitable for you. For more details, please visit our website(www.autonics.com) and refer to the product manual.

[@cakadd1021]

@@AutonicsCorp ok, thank you sir

[@yudha1971]

How to set the time of the temperature operational? Is it include in this TZN series?

[@AutonicsCorp]

It does not support setting the operating temperature. Thank you.

[@arifrahmansaleh2594]

How to setting as a cooler controller and set the gap with sv?

[@AutonicsCorp]

First, set [o-Ft] of parameter 2 group from [HEAt] to [CooL]. Then, set [P] of parameter 1 group to [0.0]. (This means using it as an ON/OFF control.) Lastly, set [HYS] of parameter 1 group. (This means a gap with the Set Value.)

[@josemiguelmachadomendoza2607]

Excelente informacion. Demostracion suficiente.

[@dimassetyoadjie9884]

i was setting to input type K Thermocouple but display status still open, how to fix it?

[@AutonicsCorp]

Please check the sensor wiring once again. In case of thermocouple, connect (+) to terminal B and (-) to terminal B'.

[@dimassetyoadjie9884]

I was make sure the sensor Wiring on that terminal and the display still open. how should i do ?

[@AutonicsCorp]

If so, it could be a problem with temperature sensor or temperature controller. Please test by replacing the temperature sensor or temperature controller.

[@amanhanif5582]

Can i change my old model which is datalogic qs/qd series with tzn4s-14r

[@AutonicsCorp]

Actually, TZ/TZN series is also an old model. Please check with the TK4S-14RN or TX4S-14R.

[@TechTricks786]

Amazing 👌

[@raulmendozachichoky9511]

buenas una pregunta tengo un controlador de temperatura tnz4s-r14 si le conecto la termo coupla tipo j queda intermitente LLLL si se la quito queda igual que podría ser me podrían ayudar gracias

[@AutonicsCorp]

Compruebe si [In-t] del grupo de parámetros 2 está ajustado a [JIC.H].

[@yersonantezana1650]

Yo temgo uno igualito pero me marca open k puede ser la termocupla es de tipo k 1200

[@AutonicsCorp]

[OPEN] significa que el sensor está desconectado. Compruebe los terminales de cableado del sensor de temperatura. Compruebe si el tipo de entrada [In-t] coincide con el tipo de sensor de temperatura utilizado.

[@yersonantezana1650]

@@AutonicsCorp ok gracias estimado

[@ulfabramantya6536]

how to fix error LLLL tzn4s-14s ?

[@AutonicsCorp]

'LLLL' is displayed when an input lower than the measurable value is entered. (For example, 4~20mA is measured, but 0mA is input) Please check the sensor wiring and check if the sensor is broken.

[@asepsaepuloh8572]

Cara setting temperatur celcius ke farenhait

[@saithan66613]

Bisakah tzn4s 14r pakai ssr..???

[@AutonicsCorp]

TZN4S-14R is a relay output and SSR is not available. Please use the TZN4S-14S product.

[@juniorquerevalurojas7289]

Thanks for the video

[@emipvargas38]

Hola quiero que ayude soy de Chile yo tengo un conteo de temperatura modelo TZN4M QUIERO A SER FUNCINAR CON UN CONTACTOR DE 380V.×50A PODRÍA MANDARME UN DIGRAMA ME ENTEREZA PORFA QUIERO INSTALAR EN UN BAÑOS SAUNA GRACIAS MUCHAS GRACIAS

[@AutonicsCorp]

Please contact our Chile customer service at [e-mail]

[@emipvargas38]

Espero su respuesta.

[@abosreaamohmed686]

Programmable counter tzn4h

[@sedomar2893]

Work good

[@saithan66613]

Panasnya naik terus tidak mau turun

[@AutonicsCorp]

Sorry. We need a little more information. (Model name, Condition, Other symptoms...) Please check if the heater is operating as the OUT indicator on the front part turns on.