ALTERNATOR REPLACEMENT REMOVAL MAZDA CX-7 MAZDASPEED 3 6 CX7 2.3

[@AutoRepairGuys]

⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: kzbin.info ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys

[@gustavoadolfoc9011]

Hey guys I have a Mazda 3 2012 do i need to change all the alternater to fixit

[@mysticjedi6730]

how many miles or km did the alternator go out?

[@jessemcveigh3511]

Please keep making videos for mazda especially the speed or cx7(since same motor) I love that you guys say what size sockets and stuff like that. Keep up the great videos! Very informative

[@ourmark100]

Thanks for this excellent video. For those of us with right-hand drive vehicles, access is more difficult because the brake master cylinder and reservoir are located on the same side as the alternator. I had to remove the intercooler (and cover), the heat shield over the exhaust manifold and the rear intercooler bracket. I also removed both nuts holding the brake fluid reservoir to the bulkhead so that I could move that around as needed. That gave me just enough room to get the alternator past but it was very tight and a lot of wiggling / rotation was needed. Also, if you are a clumsy oaf like me and you pull the small wires out of the back of the connector while trying to remove it, the grey wire goes at the top with the blue one below. If you are lucky, the wires will push back in and still make a connection. I used a ring spanner on the tensioner with a breaker bar as a lever between the back of the engine and the spanner. I then tied a rope around the breaker bar to hold it in place.

[@vicdodek]

Man I just wanna say thank you!!! Your video’s have saved me so much headache working on mine man thank you!!!

[@ohmboytx]

so how do you remove and replace the alternator with the engine in the car? I'm not taking the engine out to do that.

[@titinhdz3960]

You need to remove the engine hahah

[@skantosv6927]

@@titinhdz3960no u don’t

[@bjbilbo82]

You can do everything through the cover under the passenger front tire

[@robertnapper6085]

Thank you for your videos. I've watched a few and have been a big help.

[@rfullington]

Great video!! Perfect!

[@ethansaccount997]

Thanks, it was informational and helpful.

[@ДжерриБоиль]

Ты крутой парень, спасибо за видео.

[@haircareking]

You do good Video.

[@Trohkima_Lalli-2023]

Спасибо, пригодилось.

[@glenwhitestofer6420]

10 12 14 and 17 mm are what almost all asian cars use

[@tonyj9281]

Thanks

[@pingpong9656]

Do you have a video showing how to remove an engine from the CX7?

[@BalikbayanLifeTV]

My mazda cx7 2007 need to replace tge alternator because high voltage what is the part number? Thanks

[@donkiko6708]

How long does the battery have to be disconnected before I take of the alternator??

[@mauroserna3237]

hello I hope you can help me, the alternator of my mazda 6 2007 was damaged so I got another one, the problem is that the damaged alternator has 3 pin and the one I got only brings 2, what can I do? Thank you

[@pvt-mjsupp4241]

If i break that first threading taking off the vent, how bad is that?

[@manycrack8248]

I have a Mazda CX7 2.3 2007 I took it to the workshop because it marked a witness of the battery they took the alternator and changed the regulator they installed it again and now it fails me it turns on the indicator of the battery and it is removed but it activates the anti-skid and leaves the truck in 3rd I have to turn it off and on again can someone help me ???

[@sidcrocker3452]

👍 👍

[@chrisbettis178]

Let me see the plug that way I can see were the white and blue wires go on the pig tail plug

[@ManifestPhil99]

Guys, We aren't doing this with an engine outside the car. Since you are changing engines. take the one off the CAR>

[@yodaman1725]

I think the most important part is how to get it out and you skipped over that part