Autostart and Nordic Start Programming How To

Autostart Pro Start and Nordic Start Remote Transmitter Fob Programming How To.
Autostart’s elegant Signature Series transmitters mark a giant leap forward in 21st century vehicle security and remote start and an evolutionary milestone for the keychain remote. These are Autostart’s thinnest, most advanced 2-way and 1-way remote controls ever, with a clean sleek ergonomic industrial design, made to fit the user’s hand comfortably, enabling effortless and intuitive single-handed operation.
These Signature Series transmitters employs Spread Spectrum Technology (SST) and Advance Encryption Standard (AES) to offer ultimate security and immunity against signal jamming and interception. The result is a rock solid range of up to 5,200 feet (1,584 m).*
www.lesscosales.com

[@tipabr]

Thanks! I couldn't find the info I needed anywhere else. My wife bought a used Toyota Highlander with the AutoStart HDR, NAH5603 (no manual). After replacing the batteries in the fob it quit communicating with the vehicle. There was no hood pin, and a reprogramming method I saw using the antenna button didn't work. After locating the control box under the dash and wiggling it free, I was able to access the button on the side. I held it down for 4-seconds, then held down the lock button on the remote. The horn started honking. I couldn't get it to stop by putting the key in the ignition and turning it off and on, but then I hit the lock button on the remote again and the horn stopped. The fob/remote now seems to be communicating properly with the control box once again! Thanks :-)

[@daltonhalliday]

Thank you I reprogram my fob for my truck now it works

[@sirepoutine]

It worked! Thank you for this video.

[@Thoy28]

It's worked thanks for the video 😊🍻

[@bbg5000]

Is it possible/easy to upgrade an aftermarket starter that is already installed by simply plugging the new one into the existing harness?

[@Lima_Delta_Romeo]

Does work with my 2008 rav 6. I changed the battery on my car and not my remote starter doesn't work.

[@tuffy16]

and after entering programing mode and u turnb key on off press lock and you dont get the 5 beeps? Remote not recognized?????

[@vitiaziok]

Any ideas why parking lights don't turn on?

[@ahmedalkhaldi1104]

Thank you for this info my question is can I program any key from autostart model in my autostart?

[@homediddy383]

Thank you so much!!

[@y.b.zgaim3766]

Thank you for the information my question is that sometimes the locking and unlocking of the doors is difficult to do i feel like as a bad signal.... I checked the batteries of the two remote controls, they are new and the interior locking and unlocking is done manually very well. thank you for your help

[@garn1177]

Weird, I can't find a box that big or the push pin.

[@karenbrunette5362]

Seen your video of the autostart programming when using the bottom on the thing under dash does the hood have to be open please help

[@chriscrystalbarclay1090]

Im having an issue with my remote maybe you can help. it locks and unlocks without an issue but when i hold start .. the lock and start button flash and no start. know what that might be?

[@brianduyn6359]

It’s probably in “Valet Mode”.

[@Grizzmc13]

My pb is not working and neither is the hood pin. The truck will go in and out of valet no problem but I can figure this out.

[@YouTooCanDo]

Can you provide a detailed video on a car ????😊

[@MKLogan-yl9wj]

Thank you for this video it is very infomative. . I cannot find any information on what all the buttons, or combination of buttons do on the fob. I have a NAHTDK4 5 button fob. I am most concerned that I cannot start the car without using the fob and what happens if I lose the fob or the battery goes dead. Is there any way around this?

[@Lesscoelectronics]

+Mericko the remote cannot keep the vehicle from starting, you have a valet switch, right?

[@MKLogan-yl9wj]

Thanks so much for your very speedy response. As this was a used car purchase I have no manual for the remote system. I did read that a combination of fob buttons could take you in and out of valet mode. I also found some instructions that referred to "sub menu". Vehicle is 2006 Suzuki areio.

[@MKLogan-yl9wj]

+Lessco Electronics I cannot find the mention of a valet switch in my car manual. When I open the car with the key only, I cannot start the car unless I press on the "unlock" button on the fob. Is there a way around this?

[@highlandsoutdoors2041]

@@Lesscoelectronics do these units come with a SH (433) 120 Antenna? i have one in my car that was installed when i purchased the car ,, the fob was broke but it came with a replacement with FCC ID: NAHTDK4 what i would like to know is if that remote is compatible with that antenna or did someone at some point switch the antenna for a different remote to work because i cant seem to get it to work its a NS 1074 Unit in the dash ,, it says i have the right fob when i look up the unit in the dash but when i search the antenna i get a similar looking fob but has a different FCC id : EZSNAH2503 that's what i get when searching the antenna

[@wilsonmanlapaz1470]

hi i have a question again. iam program the unit but my problem is they not star the engine i press unlock its work and lock the trunk and star engine they not work can you give me advice to how to fix this problem thanks you

[@Pconn71]

do you have any information on the old Command Start CS 2400/2500 model with a two-button remote?

[@nathanmichaelfletcher1127]

My parking lights did not turn on 😢

[@Diecastcraze]

Tried pb button nothing happend Please anyone its 2012 honda crv and problem occur after battery died on car and had to boost , after that remote start stopped working ..(

[@serdarcellat2501]

i have ps 3175 e polarstart but no more working i need a new where can i get it just door locked system working engine start doesnt working i m in canada

[@Lesscoelectronics]

Id look for a local dealer near you, I am way down here in Florida

[@jameslaine2472]

And what if pressing-and-holding that "PB" button doesn't turn on the parking lights, like you said it would?

[@pedroneufeld8521]

On my car I had to push the hood button twice and then I turned my key on the off and then press the lock button until I heard a click

[@balbutie]

i have anxiety i cannot do that.

[@SA-jz6pb]

Thank you

[@Lesscoelectronics]

Glad it helped..

[@highlandsoutdoors2041]

i am having an issue with mine ,, original fob broke worked good for many years got a replacement but the hood pin is broke too,,, tried to program the new fob but the button will not do anything unless my hood is up and there is ground to the wire that goes to the hood pin , any ideas? is there a toggle switch on this units?

[@Lesscoelectronics]

hood pins are optional, look under the hood..

[@highlandsoutdoors2041]

@@Lesscoelectronics what antenna does this unit come with in the box ? It's a NS 1074 ,, I have a Sh (433) 120 antenna ,, according to my searchs I should have a fmtw121 or fm122 antenna , the unit was in the car when I got it and the old owner bought a new fob because the old one broke during changing battery , so I'm not sure what FCC ID it had but the new one is FCC ID NAHTDK4 ,, I don't think it's compatible with the SH (433) 120M am I correct do you know

[@highlandsoutdoors2041]

@@Lesscoelectronics i think i just need to get the NAH2503 remote

[@davidshale1836]

I have this exact same remote. Door locks work but the vehicle will not start. i hear what sounds like one click followed by two quick clicks. There is no hood pin. I cannot get manual at the Nordic site. Seems to not exist anymore.

[@Lesscoelectronics]

check if you have a disable switch under your dash

[@kirkw6918]

last fall I had to replace the battery in my 2003 Honda Accord EX Coupe ever since then my command start tries to start the car but will not fire the engine the key fob still unlocks the doors locked them and Pop the Trunk not sure if this was because I replace the battery and it has to be reprogrammed any suggestions would be grateful

[@kirkw6918]

I just had Tiger Automotive take a look at it and all they had to do was reprogram it due to the fact that I had to replace my battery only cost 38 bucks done thank God cuz we just hit bad cold cold cold cold spell 31 feels like 40 with the windchill

[@nn260]

Kirk w Reprogram the remotes or module ?

[@lex0007000]

For some reason this sequence does not work for my Autostart AS 1780. I bought a new remote because my old one does not work anymore. Help? Thanks.

[@Lesscoelectronics]

Try programming them in a different order

[@lex0007000]

How? Any sample?

[@tteuvky]

i did as you said but parking lights don't turn ON at all. any idea?

[@Thoy28]

I replaced the hood switch than do it...Gluck!

[@tteuvky]

@@Thoy28 ok, my autostart crank engine for 1 sec but this is not enough to start the engine and it never start just shutdown. Do you know how to Increase crank time so it will give enough to engine to start ?? Thanks

[@Thoy28]

@@tteuvky Hi sorry I didn’t have that problem….tried checking the spark plug that your remote starter wire connected to…. Or programmed the remote again 👍

[@Thoy28]

Pop up your car hood and press the hood switch way to program

[@tteuvky]

@@Thoy28 there is No hood switch in my conrolla 2008

[@mattandkatchristie2552]

Great video but Didnt wirk for me

[@DeeHermanson]

Did you end up figuring it out

[@ShinyCrazyLemon]

I have Nordic Start system. I watched this video and kzbin.info/www/bejne/b2bdgoVpmKt8rKc; both are great but none of them solved my problem. I don't have hood pin installed and pressing the PB (push button) on the controller box did not work initially. Connecting the grey wire to ground on and off (as shown on the other video also didn't work). However I grounded the grey wire from the controller box for the duration of programming (can be connected to chassis ground or negative battery pole) and then used the push button as presented in the video and programming work just fine. KZbin video suggest to watch for flickering lights however in my car the system is not connected to the lights so the lights didn't change state but I could hear relay clicking in the control box when I expected lights to come on or off. I only had to programm the new fob, the old one stayed programmed. For people having hood pin installed I would expect that that the hood should be open (to ground the grey wire) during the programming process.

[@highlandsoutdoors2041]

I'm trying to reprogram a fob for mine ,, have the same issue ,, dont get any lights unless i connect the hood pin wire to ground anything special you did?

[@thtsfhuny]

This is useless all I need to know is how many times to turn it on and off so I can program it so it'll start my car I don't need to know how to install it