TRUGLO TFX Pro Tritium and Fiber Optic Xtreme Handgun Sights for Glock Pistols

[@johngrunwell2412]

Very well done, I’ve done many of these. Only a note is standard procedure is left to right to remove followed by right to left to install. This also applies to all pins. Gunsmith rule. That said, very good video and use of your sight pusher as well confirming with your mic. VERY GOOD JOB. That front post is the bear and must be centered at the dot as the sight is loose in the oblong Glock hole. Being off by .02mm will put you in the 9-ring at 21 feet, even with a centered rear sight. As you have done, must mic it always. I’ll trust you with my sight installation.

[@marsoelflaco5722]

Note: Put the front dot well into the U notch, and keep a "Combat Hold." The front sight should completely cover the target. The tops of the dots should be even. Not the tops of the metal casings. Equal light between the front blade and rear notch is the same as traditional iron sights✌🏾🎅🏼.

[@AxlesGarage]

Thanks for the tips

[@EDCCarry]

U can use painters tape to mark where the oldnsight was kinda a refferance

[@Carnaln8ure]

I am looking to upgrade my sights on my CZ 75 B D. I was looking that the same type sights and your video was a nice tutorial to let me know what to expect. Thanks!

[@tonyn152]

Good job! I actually just had these same sights put on my Shield Plus today. I don't have a sight pusher, so I took it to a local gun shop and had the gun smith put them on for me. You just saved $45 (minus the cost of your tools). I would be interested in a follow-up video on how you like these sights.

[@smokintruker27]

great video I'm a certified Gunsmith and Licensed FFL dealer, these sights are very nice works great for people with bad eye sight and need alittle help with picking up sights when aiming, only problem is the sight pusher I tried the VISM and you're limited to slides you can install sights on, best sight pusher is the REAL AVID sight pusher, as setting your sights use a white grease pen and mark your factory sights and when pushing in your new sights align new sights with grease pen mark

[@AxlesGarage]

Thanks for sharing

[@tiffany52007]

My Glock 19 is in the shop now getting a cerakote job and these exact same sites installed I can't wait to pick it up❤

[@AxlesGarage]

Really like them

[@tonymediati8274]

Great video , I installed them on my G21 and love them 👍

[@AxlesGarage]

They really are great, I need to do a follow up video.

[@JesusIsGod222]

Thank you sir . great video . just order mine TFX PRO for my Glock 31 and order a VISM tool as well . very informative video specially for a beginner like me .

[@AxlesGarage]

Good choice! You're gonna love them. I should have done it years ago

[@EduardoTorres-q9c]

Those sites are pretty good. The only thing I little scared is the front part is a lot of play to it when you screw it in it shouldn’t have any play left or right that’s the only thing that scares me that good job MY BROTHER well done.

[@ngirardo86]

10 inch pounds you just did about 30 lol and the lines on the top are for installing and you could have gotten it perfect if you’d have marked them on the stock one.

[@RyDaHero10]

Is the other screw for Gen 5? Planned on getting these for my g26

[@leoarreola9458]

Do gen 4 sights fit gen 3 Glocks?

[@funnypotatoman773]

i got it in my taurus g2c and love it the only problem i got is the front sight is tight but when i go to use it shot the first round and it get lose not much i tight it but i go shot it it get lose how can i fix that

[@AxlesGarage]

Locktite