Thanks for your detailed instructions bud, I just finished modifying my pump. It improved the suction a lot. I didn't have a welder so I used Pratley Steel to secure the handle. This video was a great help. Tested it on a bucket of water. Works great. 👍🤗.
@MADAngling2 жыл бұрын
No problem, the silicone gets better the more you use the pump
@herbmeister357 Жыл бұрын
I make silicon washers for my pump…I find it easier to mix some soap and water and squirt the silicon into the soapy water,then put my hands into the soapy water and mould the silicon into a ball(it will not stick to your hands👍)…then put a bit of soapy water on my glass and in my washer/gasket mould and press the amount of slicing I need into mould by hand and flatten off with a plastic trowel(and soapy water)…as well as preventing sticking and mess the soapy water also helps speed up curing of the silicon you can pop 22mm washers/gaskets out of the moulds in 3-4 hours and they’re usually fully cured and ready to use in 4-5 days👍 another tip that might help is get rid of the wing nut(they tend to turn and constantly adjust the suction each time they make contact with the sand) replace it with a nylon assisted lock nut👍 other than that great video👍👍👍
@MADAngling Жыл бұрын
Thanks for sharing ur way of making them... Will definitely give it a try x2 thumbs up
@SAMMY123292 жыл бұрын
Thanks that's a real help to me, would never thought of that. Made three, they take a long time to dry. Will install when ready Chris.
@MADAngling2 жыл бұрын
It does take time to dry... Well worth it when ready.. Enjoy
@michaeleverton4882 Жыл бұрын
🎣 i have an Alvey steel bait suction pump and a blue pvc plastic pump. I make my own washer systems to put in them which gives my pumps Much better suction power than what they had! No need to take the metal cap - lid off! It keeps the sand and water out. The water, sand and mud gets in Below my washers. I suck up some clean salt water when finished pumping and some fresh water at home to clean the inside of pipe! 🦐 🎣
@EnduroDroneHub2 ай бұрын
That bait pump is a beast! Where can I get that bait pump! Not just “a bait pump” THAT one 🙂🤷🏻♂️
@MADAngling2 ай бұрын
Drop me a mail Madanglingadventures@gmail.com
@faiekfredericks72554 жыл бұрын
Awesome video, this video tutorial will make things so much easier. Thank you MAD Angling!
@lancelouw26394 жыл бұрын
Definitely what I needed boet, thank you boet.
@MADAngling4 жыл бұрын
Thanks glad to help
@russellmoss64874 жыл бұрын
Brilliant! Great innovation.
@nataliegovender14144 жыл бұрын
Thank you for SHARING.. wonderful video!!!!
@ashleyjulius4544 жыл бұрын
Great content as usual...enjoy your videos sir, keep up the great work
@shameerarendse2804 жыл бұрын
Mooi man boeta waanie.. been waiting long now for this video
@bradparker61569 ай бұрын
A question I have regarding this modification: Is there any reason one may still want the top end to be sealed? (As unmodified) I cant see any..
@MADAngling9 ай бұрын
It's not necessary to have it on..does not help with suction
@drevil4454 Жыл бұрын
Nice mod bruh. Now can you still pump prawn?
@maxmuskat98635 ай бұрын
genius man!
@sao680532 жыл бұрын
I get the silicone washer part but what’s the point of the top end modification
@MADAngling2 жыл бұрын
The removal of the top washer allows the pump to be used under water, so when u pump these no restriction the water flows quickly out
@ahndeux2 жыл бұрын
@@MADAngling Yeah, but wouldn't drilling two large holes on the top cap serve the same purpose?
@sadickvanderschyff18074 жыл бұрын
Nice one Redewaan but we all can't mig like u can we braize
@MADAngling4 жыл бұрын
Any weld will work, just needs to be secure
@TheIncredibleMrG7772 жыл бұрын
Awesome video bud👍🏻👊🏻👊🏻
@MADAngling2 жыл бұрын
Thanks for watching Gavin
@robertaflint65893 жыл бұрын
There is no need to take the cap off the top, all you need to do is drill a small 4-5mm hole just below we’re the handle pokes out, no need for welding, this hole can be used to lube your pump as well , I use a bottle from when the wife dyes her hair, the bottle has a nice point , ideal.
@MADAngling3 жыл бұрын
Drilling holes will definitely work.. Main aim is to get the water quickly out... What kind of lube do you use Robert
@robertaflint65893 жыл бұрын
I just use good old fairy liquid.
@robertaflint65893 жыл бұрын
If the seal is good on your pump you shouldn't be getting any water in the top part of the pump, I have an original Alvey pump and never had a problem with water getting above the seal, except on purpose to flush and clean.
@waynemorris50843 жыл бұрын
Hi do you rework pumps plz i dont have the tools to make it the way you make it im not in a rush if you dont have the time
@MADAngling3 жыл бұрын
Drop me a mail Madanglingadventures@gmail.com
@waynemorris50843 жыл бұрын
Hi
@jeromepetersen65843 жыл бұрын
Great clip & very useful ( cheers jpet )
@chrislaing13564 жыл бұрын
Well done👍🏻👍🏻
@AndrevanNiekerk-qg4dm8 ай бұрын
V Thanks for the video. Just turn down background music, can hardly hear you
@steveellis60903 жыл бұрын
Why don't you form the center hole while it is still soft ?
@MADAngling3 жыл бұрын
You can,will give it a try
@alistairmacdonald66539 ай бұрын
Why don't you use a nyloc nut instead of the wing nut . Just take a spanner with you when you go after bait
@MADAngling9 ай бұрын
We do that yes...my 13 spanner stays in the worm bag
@T3Beatz3 жыл бұрын
Thanks for sharing!
@mariojacob791 Жыл бұрын
How to make own bait pump for ragworms and beach worms
@antonschutz87926 ай бұрын
Anyone knows who can fix a prawn pump for me, please
@MADAngling6 ай бұрын
Sure I can fix it...drop me a message 0653056060
@davidtilly21422 жыл бұрын
Hi where can I buy a pump thanks.
@MADAngling2 жыл бұрын
Drop me a email with ur contact number
@asifisraelfishing4 жыл бұрын
Cool video.. will help
@24ジャックバウアー3 жыл бұрын
素晴らしい😊👍
@ahndeux2 жыл бұрын
Wouldn't it be easier to just drill a hole for the air and water to get out? Not many people have a TIG welder in their house.
@MADAngling2 жыл бұрын
Definitely worth a try, try and get as much holes in as possible the less restriction the better
@erniecrowley26033 жыл бұрын
Why not let the silicone cure inside of the tube then just cut 20ml sections off it
@MADAngling3 жыл бұрын
Would be difficult to cut it perfectly round. And the silicone tube is the right diameter
@brandonmichaels85042 жыл бұрын
this is a very useful vid thanks for sharing gonna tell all my friends to subscribe thumbs up
@MADAngling2 жыл бұрын
Thanks Brandon much appreciated
@aashiqebrahim15154 жыл бұрын
Nice uncle
@agentagent28274 жыл бұрын
Shot waanie wakes!!! kwaai man !!
@tarellmathibemathibe71834 жыл бұрын
Are u going fishing now
@MADAngling4 жыл бұрын
Yes
@BOVVIR2 жыл бұрын
awesammm thx.. auto subs...
@ziyaadhoosaindelavega30814 жыл бұрын
Kwaai
@dalestephenson87694 жыл бұрын
Could you do mine for me? At a price of course ☺
@MADAngling4 жыл бұрын
madanglingadventures@gmail.com drop me a mail
@tarellmathibemathibe71834 жыл бұрын
Hi
@MADAngling4 жыл бұрын
Hi
@TR4zest3 жыл бұрын
know you mean well, but with a poor mic, the background musak makes this unwatchable.