Back Taper on Drills: In The Loupe TV Short

  Рет қаралды 1,505

In The Loupe TV

In The Loupe TV

Күн бұрын

Пікірлер
@rosswagner3021
@rosswagner3021 Жыл бұрын
Don I love all these you do. Even though I knew this I’m sure there are a lot of people that don’t. I like watching all of these because I never know when I pick up something I didn’t know. Thanks again!
@muralinaik6511
@muralinaik6511 Жыл бұрын
Oh.. We were in myth that, through out the flute it has same dia.. But why this is not mentioned in supplier Or tool maker drawing?
@CuttingtoolCounselor
@CuttingtoolCounselor Жыл бұрын
Endmills and Reamers have the same diameter throughout, but Drills have varying Backtapers so the friction is reduced in the hole. I say Varying because some Carbide HP drills might have more than HSS drills. HSS would have around .0002-.0005 per inch and Carbide could have up to .003 per inch pending the MFG and application ( Deep hole) Ctc
@muralinaik6511
@muralinaik6511 Жыл бұрын
​Thanks!
@danhnguyen435
@danhnguyen435 Жыл бұрын
Thanks
@CuttingtoolCounselor
@CuttingtoolCounselor Жыл бұрын
Welcome
@schutzi2282
@schutzi2282 Жыл бұрын
Had to skip through most of the video to get to a single point.
@dallinnielsen7514
@dallinnielsen7514 Жыл бұрын
Even though you didn't ask, here's some constructive criticism. You're talknig to hardly anyone. If you want to gain an auadience, cut out all the unnecessary talking. Video Should have started at 1:40, and ended at 2:40. And even during that time you did a lot of rambling.
@muralinaik6511
@muralinaik6511 Жыл бұрын
Nope... Nothing vis unnecessary here.. He mentioned at starting.. It's a short video.. And we the audience are ok with little fun.. His sessions are full of knowledge.. He is helping us by sharing his knowledge..
@CuttingtoolCounselor
@CuttingtoolCounselor Жыл бұрын
I appreciate the Feedback.. I also appreciate you watching.. This one was shorter and could always have more technical info. Ctc
@CuttingtoolCounselor
@CuttingtoolCounselor Жыл бұрын
Love your support!@@muralinaik6511
Diving Into Drills: In The Loupe TV Ep. 18
25:48
In The Loupe TV
Рет қаралды 3,6 М.
The Different Types of End Mill Reliefs: In The Loupe TV Short
11:33
In The Loupe TV
Рет қаралды 1,9 М.
Что-что Мурсдей говорит? 💭 #симбочка #симба #мурсдей
00:19
She made herself an ear of corn from his marmalade candies🌽🌽🌽
00:38
Valja & Maxim Family
Рет қаралды 18 МЛН
VIP ACCESS
00:47
Natan por Aí
Рет қаралды 30 МЛН
Keys To Cutting Composites: In The Loupe TV Ep.16
14:26
In The Loupe TV
Рет қаралды 2,2 М.
UNIFIED MULTIAXIS with Mastercam 2022
6:21
ProtoTek Engineering
Рет қаралды 8 М.
What You Don't Know About Weldon Flats: In The Loupe TV Short
11:27
In The Loupe TV
Рет қаралды 1,6 М.
Understanding Composite Cutting Tools: In The Loupe TV Ep.17
19:52
In The Loupe TV
Рет қаралды 2 М.
Introduction to Circle Segment Machining: In The Loupe TV Ep. 25
14:22
In The Loupe TV
Рет қаралды 3,1 М.
Ball Nose End Mills & Chip Thinning: In The Loupe TV Short
14:05
In The Loupe TV
Рет қаралды 2,6 М.
Knife Like Razor Sharp! Sharpen Any Knife in 1 Minute with an Old Battery
10:12
НИКОГДА не иди на сделку с сестрой!
0:11
Даша Боровик
Рет қаралды 729 М.
Таким раствором работать одно удовольствие
1:00
Профессия созидатели
Рет қаралды 954 М.
Satisfying Vend 😦 Ep.5 #shorts #satisfying #vendingmachine
0:23
TYE Arcade
Рет қаралды 17 МЛН