@brandyn420420 That circle is just to make sure the slide is installed properly. To "properly" sync the carbs you need a tool that measures the air flow into each carb. You can also "eyeball" the syncing by just setting both slides to the same height.
@brandieshaydaniels25269 жыл бұрын
I kept racking my brains wondering what I could make it with, last week the same thing hit me. Haven't had a chance to make one yet. Weather has been crap for week. Thanks for the vids. Very useful.
@SparkysGarage9 жыл бұрын
David Daniels Glad to hear it!
@jaynrudy12 жыл бұрын
Thanks for responding so fast I was told by the shop it is running rich I will not ride and I'll take apart and find out what is in there and get back to you thanks again
@TheCapTan10 жыл бұрын
Thanks for your vids. I got mine running smooth. Clogged pilot jet. You can still see through it but the unclogged ine had a bigger hole. I moved up to a 27.5 anyways.
@SparkysGarage10 жыл бұрын
PeterSouth Awesome :)
@XrJay0312 жыл бұрын
I can clearly see this is your passion, Appreciate the videos man, you make majority of the people on bansheehq look like a joke. kudos
@SparkysGarage12 жыл бұрын
I wouldn't recommend riding anymore until you know what jets are in the quad for sure. It might be running lean and that'll be expensive to fix. Ill shoot a vid on changing the needle position today if I can get the time. Ill definitely do one soon though.
@christianhinds551011 жыл бұрын
found your video on the blaster forum and my carb was leaking gas, was gunna do a rebuild, but i watched this vid quick went thru cleaned my carb and adjusted my floats, my quad runs like a top without leaking any gas, just wanted to say thanks cuz i was getting irritated by looking at my quad just sit there
@outsidedude113 жыл бұрын
what i found easiest is to take an impact screwdriver and using that with light taps to take out the carb bowl screws
@shaker34598 жыл бұрын
Good video. Thanks much for taking the time!
@SparkysGarage13 жыл бұрын
@125RiderSuzuki A rebuild kit wouldnt hurt depending on the condition of everything inside. Go for it if its never had a rebuild.
@SparkysGarage12 жыл бұрын
@Kinkryder8 for this vid i did not have the tors removal kit installed. I did a video of the tors delete kit install after this vid was made though.
@brentp.4090 Жыл бұрын
Thanks very informative
@SparkysGarage12 жыл бұрын
Thanks! So glad im getting positive feedback
@junkymustangs11 жыл бұрын
the idle air screw works the same on both 2 or 4 strokes, it just controls air at idle, after you open the throttle it doesn't do any thing
@352ish12 жыл бұрын
Great video bro. Wish u lived in central Florida
@SparkysGarage13 жыл бұрын
@outsidedude1 Good call. That should work. Thanks for watching.
@SparkysGarage12 жыл бұрын
Thanks a ton, so glad to hear positive feedback :)
@jaseclark99163 жыл бұрын
a tip : watch movies on Flixzone. Been using them for watching loads of movies lately.
@marshallclay49783 жыл бұрын
@Jase Clark Yea, have been using flixzone} for months myself :)
@SparkysGarage12 жыл бұрын
@XrJay03 Thanks man, that means a lot. I definitely love shooting these vids for everyone.
@SparkysGarage12 жыл бұрын
I was literally in Orlando yesterday... I just got home yesterday morning. lol
@scottbrooks350212 жыл бұрын
Good stuff bro
@aig27610 жыл бұрын
Excellent video! Thanks!
@erichoward1512 жыл бұрын
I really appreciate you putting this up man, helped out alot!
@lukasmarlon58463 жыл бұрын
pro trick: watch movies on Kaldrostream. I've been using it for watching loads of movies lately.
@TheCapTan10 жыл бұрын
I have a problem with getting both cylinders to run evenly. I cleaned the carbs and jets and also made sure that. Engine runs great after half throttle but at idle right pipe does not get hot and left also hits harder.
@SparkysGarage10 жыл бұрын
I did a vid on uneven pressures, check it out.
@SparkysGarage12 жыл бұрын
As long as the center hole is the same size it will be fine.
@ImFromDadeCounty10 жыл бұрын
Sparky you are the fuckin man. My carbs are running crispy as fuck thanks bro
@SparkysGarage10 жыл бұрын
Awesome glad to hear it :)
@SparkysGarage12 жыл бұрын
@brandyn420420 If you have a little carb cleaner in the float bowls it wont be a big deal to fire it up as long as there is gas in there with it. 340s sound right and 290's sound a little lean. Try shooting somewhere inbetween and do plug chops. Ill have a video of that this summer.
@SparkysGarage13 жыл бұрын
@gsxrboy09 I did take them out and clean them and reinstall them. Just wasn't able to get vid of it.
@DocArain500011 жыл бұрын
Great video! Very informative!
@gmhammerfist8913 жыл бұрын
@outsidedude1 i figured i might as well get rebuild kits for them anyways because it has been sitting, and the fact that they haven't been rebuilt before.
@SparkysGarage12 жыл бұрын
your best bet is to post ALL your mods, your riding temp, and elevation over on banshee hq. Id love to help but im not familiar with a 2-1 jetting setup. Only familiar with stock carbs
@brandyn42042012 жыл бұрын
@jlsparky7 thanks man.. and it has run with 290s for atleast a year or so the previous owner told me.. the plugs got pretty black and just signs of it being rich.. but I guess 300s wouldnt hurt? I also cant seem to find the little circle in the glass window for syncing the carbs
@SparkysGarage12 жыл бұрын
No I don't. I'd love to one day though... I live in Michigan.
@SparkysGarage12 жыл бұрын
@hexs23 Do a search on leak down tests and also check for exhaust leaks. Have you installed the TORS eliminator kit? Thats not a bad idea to do either.
@SparkysGarage12 жыл бұрын
Amsoil Dominator 40:1 I used to be an Amsoil preferred customer and had it delivered to my place. I just buy it at the local powersports shop now,
@SparkysGarage12 жыл бұрын
Glad i was able to help :)
@SparkysGarage12 жыл бұрын
An improperly adjusted float, a dirty float needle or seal, or leaking floats.
@SparkysGarage11 жыл бұрын
Glad I could help man. Ride hard :)
@rafaelcordova637410 жыл бұрын
So, while assembling my carbs last week I lost the Lil copper straw on the lid of the carb... what role does this straw play?
@jaynrudy12 жыл бұрын
I set both of needle clips at third notch when I went and put new 280 jets in the side with the choke the needle sticks out of the jet and the other side does not please help I did put a new throttle cable on am I doing something wrong the needles are the same length ?
@SparkysGarage12 жыл бұрын
@gringo0760 DO NOT use wd40 on anything with orings. It will make them swell and not fit. Use white lithium grease and it'll work great. :)
@jaynrudy12 жыл бұрын
Okay I was missing the brass washer that is under the jet I have also installed a boost bottle got it all back together on the third kick it sounded like it was going to run and now I can't get it to start I followed your steps to remove tores all together I do have spark I changed plugs still won't fire checked its getting gas even gave it a shot of starting fluid still wouldn't fire I emptied all gas before trying to start so it's got fresh gas 93 octane 40to1 I'm stumped? Thanks
@bombin118113 жыл бұрын
So I just bought a needle valve set because a guy said that was why my engine was leaking and not runing properly (it would start up fine and run for two or three minutes and then bog out and i could get it started... until the next day I dont know why that is but I asked someone and he said thats why....) would I bend my metal piece down the adjust the floaters?
@pcostyle117 жыл бұрын
thanks for the vid !!
@SparkysGarage12 жыл бұрын
@TheBansheeboy617 No kit. Just used the same parts
@DANKNUGREVIEWS12 жыл бұрын
can you measer the diameter of the hose so i can do to harware store and get one close to size and cut down, would be greatly appreciated
@BeEasyTreeFarmer12 жыл бұрын
what would cause my left carb to spray out fuel out of the vents during right hand turns
@DOPEPEPO10 жыл бұрын
My banshee won't stay running.. When I let the gas go it would shut off.. Do u think the carbs might be the problem??
@SparkysGarage10 жыл бұрын
Sounds like the carbs are a good possibility.
@GFreerider13 жыл бұрын
my throttle cable snapped :( do you have a video of how to replace the wire? i cant seem to get the end off from on top of the carb. help please
@notbobe66139 жыл бұрын
Hey GREAT video helped me out tons on my blaster thank you very much.
@SparkysGarage9 жыл бұрын
Kobe Kelly Glad the vid helped :)
@jaynrudy12 жыл бұрын
How can you tell if the needles are bad I recently had motor bored .30 over wiseco pistons fmf power core 2 pipes and fmf slip on also 2 into one air cleaner with no lid when I put all back to together it ran but would bog more than 1/4 throttle I don't know what size jets I have I'm new to this but would like a good starting point on what I should have in there I brought it to a shop by me and was told I needed new needles and choke plunger and throttle cable they wanted 350 to do it we needl
@jaynrudy12 жыл бұрын
I'm not sure how to pm either well I had bored .30 over wiseco pistons,boost bottle,280 mains 27.5 pilots, I put clip for needle at 3rd from bottom 40to1 gas tores eliminate new throttle cable I have spark I gave it a shot of starting fluid no difference changed plugs put couple drops of gas in where plugs go and nothing when I put boost bottle on my gas line is going over it and before it wasn't going up over it I'm going to take bottle off and change plugs and try that other than that I'm stu
@slanktapper8 жыл бұрын
For the float bowl bolts order some JIS (Japanese Industrial Standard) screw drivers. They are a true cross point and using a Phillips will strip em.
@TheFlygibby12 жыл бұрын
thanks for the video ,is great help and you explain every thing so its easier for those who know little about doing this. i just bout one of these banshees' and it does not seem to be getting fuel so i dont get what is wrong. could you give me any ideas? (i think it is fuel pump but not sure where to find it)
@brandyn42042012 жыл бұрын
@jlsparky7 I know but when you have it full throttle theres that little thing that pops up I have synced them before and done all that I guess they might just be backwards :S but it still ran like it should of..
@DANKNUGREVIEWS12 жыл бұрын
hey man, i just bought a banshee like last thurday. it runs like a beast, alothough previous owner said the left carb need to be cleaned...so that side smokes a lil bit, and it also feels its blowing exhuast harder..it starts first kick everytime btw so no hard starts.. i just want to hear your input.
@SparkysGarage11 жыл бұрын
Good video idea. Ill respond in video format soon. Thanks!
@SparkysGarage13 жыл бұрын
@bombin1181 Does the quad idle fine or does it rev up once its warm? Sounds like you might need to do a leak down test.
@SparkysGarage12 жыл бұрын
Watch my jetting video too. Sounds like your jetting may be off. Definitely sounds like your idle air control screw needs adjustment. thatll make a huge difference
@SparkysGarage13 жыл бұрын
@bombin1181 What you have is a bigger problem then just a carb it sounds like. Compression check?
@hexs2312 жыл бұрын
So I replaced the pilot jets turns on now but I get a back fire from one side and won't hold the idle I adjusted the air screw and tors nothing
@Kinkryder812 жыл бұрын
you dont have the tors removal do you? because my carbs are in a completely different spot lol. they are under and in front of the air box. like right under the fuel tank.
@hexs2312 жыл бұрын
Ok thanks i will try it
@SparkysGarage12 жыл бұрын
@ftleking1 Glad you liked the vid man! :)
@SparkysGarage12 жыл бұрын
Depending on how hard you shake the bike it just might be normal. Are the springs in the plunger working ok?
@gsxrboy0913 жыл бұрын
why didnt you take the jet's out and clean them with a needle? they get clogged up also
@bombin118113 жыл бұрын
@jlsparky7 compression other then using the kick starter how would you test it...compression is no problem while kicking what do you thing the problem it?
@bombin118113 жыл бұрын
the stator spins starts to spin really fast when its warm..the sound doesn't change how do I check for leaks
@user-by6oe7vd9g9 жыл бұрын
Thanks a lot man
@DANKNUGREVIEWS12 жыл бұрын
for some reason i cant find your video on the idle air screw, thanks a lot for your help
@bombin118113 жыл бұрын
is it ok for the needle jet to be bent (the spring) because mine it I dont know if thats a problem.
@brianj1234585 жыл бұрын
I know this is an old video but I just bought a blown up banshee that I'm gonna rebuild this weekend anyhow lol. The banshee I bought has the original TORS carbs on them like yours I'm wondering did you have problems with the TORS after your carb rebuild on your banshee??? Thanks for any info have great day
@SparkysGarage5 жыл бұрын
brianj123458 no issues after I bought the tors eliminator kit.
@YAiYIO819 жыл бұрын
I was taking off my carbs and i realized the part you say that has to line up with the notch on the body of the carb right below the top my carb does not have one? is that bad?
@SparkysGarage9 жыл бұрын
Andrew Yamamoto Some carbs dont have the piece. Most do though
@ryanlanter465510 жыл бұрын
I got an older banshee was told I needed to clean the carbs so I follows this video and did, it starts up on the first try but won't keep an idle, is there anything I can turn up to adjust the idle? And the screws above the 2 carbs how do I adjust those to normal?
@SparkysGarage10 жыл бұрын
Check out my TORS eliminator series.
@mrbigpatin11 жыл бұрын
hey bro i don't got the nudge that stick out in the middle of the carb is that a problem?
@SparkysGarage11 жыл бұрын
Im not extremely familiar with that model. Your best bet is probably to buy a manual and look it up. Maybe it is an auto-choke feature? or auto shutoff?
@SparkysGarage10 жыл бұрын
Glad you liked it :)
@brandyn42042012 жыл бұрын
hey i really need some help... I recently got a banshee used off someone and it has ran amazing for about 3 months.. it has a big bore and DG pipes.. and I just ordered a K&N lid and it came with 340 mains.. it had 290 in it and when I put the 340s in it ran like shit so I put the old ones in.. I left some carb cleaner fluid in it tho when i fired it up.. is that bad? it was revving really high and i dont want to run it anymore till i figure it out? can you help
@DANKNUGREVIEWS12 жыл бұрын
hey man you told me in another video to get some low end pipes for the boggynes, i am running fmf gnarlys and from my understandibng they should be good low end pipes. but my bike is a 392cc what jetts should i run you think. do you recommend a 2 into1 carb??
@SparkysGarage12 жыл бұрын
Is the cap screwed on all the way? TORS still installed or do you have the eliminator kit installed?
@rucingthis368910 жыл бұрын
great video, thank you... just had a question, if you know? what is the screw that is accessible under the seat, and what should it be set at?
@SparkysGarage10 жыл бұрын
That screw controls how high the slide sits inside the carb (controls your idle RPM) The problem is with the TORS they are completely inaccurate.
@rucingthis368910 жыл бұрын
thats what I thought it was but was not sure. thank you for the very speedy reply. now i just got to get it to start.
@SparkysGarage12 жыл бұрын
Try setting the float a little lower.
@Shawi712 жыл бұрын
my main jet got kinda scratched from the outside while i was tightening it is that okay? Thanks
@Rozalez32xP11 жыл бұрын
hey buddy how do you disconnect the carb from the air hose thingy?
@gringo076012 жыл бұрын
For mild lubricant can you use wd40? Or what do you recommend?
@asingh40569 жыл бұрын
okay one question...what is the part number for these carbs..im searching everywhere to figure out what carb to buy,,like...what size is the carb or what carb should i use for a stock 1996 yamaha banshee? sorry about the multiple questions bud...i just dont want to fuck up my machine
@SparkysGarage11 жыл бұрын
Glad it helped :)
@SparkysGarage12 жыл бұрын
Yes sir.
@2strokeboss11 жыл бұрын
Hey I was wondering what's a good size carb for my banshee i always go to the dunes I got toomey t6 pipes v-force reeds and a boost bottle and planning to run a 2 into 1 carb kit
@SparkysGarage11 жыл бұрын
There are 3 clamps you remove then just twist it out.
@MrDelo510 жыл бұрын
i have a banshee 2009 with FMF and Vforce3, wich is the especial carburation to this things?
@Jiggstahh8 жыл бұрын
Hey Sparkys, I have a 2002 blaster 2 stroke and when I reassembled the carb we had no resistance on the throttle. Can you help me??
@DANKNUGREVIEWS12 жыл бұрын
what kind of oil do you run? and where do you get it at?
@DANKNUGREVIEWS12 жыл бұрын
and btw is your turns,,,a full 360 or a 180....for example you said a turn and a half, meaning 540 degree turn?
@Scofari11 жыл бұрын
So is it the main jet or the needle jet that controls 3/4 to WOT?? You say opposite things in your 2 videos.
@joerod61068 жыл бұрын
nice video. Do you need 2 replace the gasket every time?
@SparkysGarage8 жыл бұрын
no, very rarely. I've own my banshee since brand new in 2004 and this is my third set.
@hexs2312 жыл бұрын
My carbs won't spray fuel I have fuel in my float bowl please help
@SparkysGarage11 жыл бұрын
No there are not jet kits on those carbs. Jet kits are kind of a waste of money because they come with VERY odd sizes. You're far better off ordering the individual jets that you think you will need.
@SparkysGarage13 жыл бұрын
@bombin1181 I shot a vid of how to so a leak down test today. ill post in later tonight or tomorrow.
@brandieshaydaniels25269 жыл бұрын
Just my luck, you mentioned making a clip for the choke, have you made one and what did you make it out of?
@SparkysGarage9 жыл бұрын
David Daniels I haven't made one yet. However it seems like spring steel would be the only option.