Beetle Engine Rebuild Part 2

  Рет қаралды 2,141

The Shop Life

The Shop Life

Күн бұрын

Пікірлер: 15
@muzzcovw7674
@muzzcovw7674 3 жыл бұрын
Just FYI, arrows do not point to exhaust! Arrows point same direction, to flywheel side. Piston pin is offset to avoid noise and excessive wear. And no rtv between heads and cylinders. It goes between cylinders and the engine case.
@unicron24
@unicron24 8 жыл бұрын
So stoked it's running again...so wished I had the garage and time to rebuild my motor.
@theshoplife9527
@theshoplife9527 8 жыл бұрын
Me too man! I've heard of some people actually rebuilding these engines in their kitchens haha just because they're so small
@felixgarwandoe3111
@felixgarwandoe3111 7 жыл бұрын
Where did you buy the new heads from ??
@6271raven
@6271raven 6 жыл бұрын
you need to get a fuel regulator Bud
@TJ102681
@TJ102681 7 жыл бұрын
hey man did you have fuel filters in between the carbs and fuel pump mine done that
@theshoplife9527
@theshoplife9527 7 жыл бұрын
tony allred I had one filter after the pump and before the T for the carbs. It's actually a fire hazard to have one in the engine compartment though so I'd recommend against it
@HotRodTypewriter
@HotRodTypewriter 8 жыл бұрын
I shouldn't need to use rtv on any of the parts you put it on. It's cool to learn on a bug though. I did, and I made a lot of these same mistakes. There are a lot of good books to show you how to build these things. Good luck.
@TheIslandIdiot
@TheIslandIdiot 8 жыл бұрын
what was the problem with the dual carbs? was planning on getting one for my beetle as well
@theshoplife9527
@theshoplife9527 8 жыл бұрын
Not sure if the problem is with the carbs or the fuel pump, but there was way too much fuel going into the carbs and the engine would just flood until it died. After the engine died, fuel would still keep coming in for about 30 seconds. I tried adjusting them numerous different ways and replaced the float in one of them (which had gone bad). From what I've read, some people have had better luck with electric fuel pumps with dual carbs. Someone was telling me that they actually need less fuel pressure, which doesn't really make sense to me but that could be the case
@TheIslandIdiot
@TheIslandIdiot 8 жыл бұрын
how big are the new cyclinders you're using? another question, would a stock cylinder from a 1600cc engine fit on a 1300cc case or no?
@theshoplife9527
@theshoplife9527 8 жыл бұрын
TheIslandIdiot they're 88mm. I don't know actually. Sorry just don't know much about anything other than a 1600.
Beetle Engine Rebuild Part 1 (Teardown)
6:09
The Shop Life
Рет қаралды 3,8 М.
Looking inside an engine during cold start (-30 degrees)
15:30
Garage 54
Рет қаралды 4,2 МЛН
It’s all not real
00:15
V.A. show / Магика
Рет қаралды 20 МЛН
Леон киллер и Оля Полякова 😹
00:42
Канал Смеха
Рет қаралды 4,7 МЛН
To Brawl AND BEYOND!
00:51
Brawl Stars
Рет қаралды 17 МЛН
Melting Copper Wire Into a River Table
16:53
Burls Art
Рет қаралды 3,1 МЛН
OPCE Four Cylinder Engine Story
11:59
prosstaylor
Рет қаралды 7 М.
A Story about the Volvo 240 and its Redblock Engine - Iconic Cars and Engines #18
14:11
Popping a 5000A Fuse
18:42
Photonicinduction
Рет қаралды 6 МЛН
Spinning Levers - How A Transmission Works (1936)
9:41
US Auto Industry
Рет қаралды 10 МЛН
Spain is Living in 2050? Revolutionary 1 Stroke INNengine Analyzed
20:31
driving 4 answers
Рет қаралды 7 МЛН
I built a FLEXIBLE ENGINE (New Rotary Design)
18:58
Integza
Рет қаралды 1,7 МЛН
Pulling The Bug Engine
6:26
The Shop Life
Рет қаралды 1,8 М.
It’s all not real
00:15
V.A. show / Магика
Рет қаралды 20 МЛН