Polaris General - Reverse LEDs Installed

I've used a couple of different models of LEDs. Here's the latest version: amzn.to/2O1Se7k. They're really bright and they work well.
Here's a list of some of my wiring components used:
Relays: amzn.to/3hLhXSq
Grounding Block: amzn.to/3f1QiuJ
80 amp Circuit Breaker: amzn.to/2SYozT6
Terminal Connectors: amzn.to/3bI3dQF
Butt Connectors: amzn.to/344LNct
12v Master Relay: amzn.to/3yuTp5Y
Fuse Block: amzn.to/3u1ePEF
Wiring: amzn.to/3oz1YbD
Heavy Duty Copper Lugs: amzn.to/2RtuWxA
As an Amazon Associate, I may earn commissions on qualifying sales. These commissions do not affect your pricing. I thank you for using my links.

[@Ron_Ackerman]

Thank You!

[@massawakening6232]

Awesome work. Did you fabricate your headliner?

[@GeneralTalkWithBen]

No. It’s the Polaris OEM premium roof (same roof, but it includes the headliner).

[@bobyates3817]

@@GeneralTalkWithBen thank you for everything that you do on your channel you do a great job and give a person a lot of ideas thank you again

[@bobyates3817]

What do you think about putting door bags on the do they have room and have a place for

[@stevekarch8505]

Hi Ben, Enjoyed the video and those Eagle Eye LED lights look awesome.Ive never wired anything other than the plug and play turn signals and horn kit on my General,but would like to wire my reverse lights like you did on here. Do you ever go into alittle more detail for us beginners on lighting?

[@GeneralTalkWithBen]

Here’s the key post from the General forums (“Reverse Lights?” Is the name of the post string, and the below is from post 41): 86 - Red wire from light and red/purple wire from harness 85 - Black/White from harness 87 - Black wire from light 30 - Ground This is how you wire up the relay to come on in reverse without a switch. Do not use the middle 87

[@JohnWilson-ql7ki]

I know this is an older post but did you wire your battery charger cable to the battery connections under the hood or to the battery directly?

[@GeneralTalkWithBen]

To the hood connections. The lines go directly to the battery.

[@Duckman2405]

Have to ask since it's been over 2.5 years. How have the LED lights held up?

[@GeneralTalkWithBen]

I’ve never really had an issue with long-term life on LEDs. However, I did have a couple of problems with the “dome” type bolt LEDs (like the ones I used for the reverse lights and the dome light-example: amzn.to/3dX23Ax). The dome fell off on a couple of them. Fortunately, I found them and superglued them back on. As for them working-no issues, though. And LEDs are always very bright.

[@2fast65]

Where did you find the head liner that looks sharp i want one for mine thanks have a great day be safe.

[@GeneralTalkWithBen]

It came with the factory “premium” roof kit. I had seen that there was some difficulty in ordering just the headliner if you already had the roof, but that may have changed.

[@2fast65]

@@GeneralTalkWithBen Thanks yes it is hard to find.

[@ryanshultz8100]

which one is ground on the tail lights

[@GeneralTalkWithBen]

I don’t remember exactly, but I think you can look at the wire and tell (I’m pretty sure the ground is a brown or black cable).

[@jefffrank6106]

How are the led backup lights attached? and do you have a part number?

[@GeneralTalkWithBen]

The video description has a link to the LEDs I used. The wiring uses a standard 12v automotive relay, but it’s wired using ground as a trigger using the OEM wiring. If you look in the comments, I think there’s a link to the wiring diagram, but you can also look on the Polaris General forums and find it there, too.

[@jefffrank6106]

General Talk with Ben does a nut go on the back side? Or are they glued in?

[@GeneralTalkWithBen]

There’s a nut on the rear. You can pull the panel off the side of the bed (one screw at the front when you lift the bed, then pull out) and reach in to tighten it (I used a little bit of locktite as well).

[@jefffrank6106]

Nice setup! My bolt lights came today, how did you connect the wires to the relay? The wires are vary small.

[@tahoe9813]

jeff frank the relay gets wired as a ground trigger rather than a positive trigger. I don’t have the link handy, but if you search on the polarisgeneralforums.com you will find the diagram. It’s very easy, and you wire it up like normal, but in the ground trigger position. As to the small wires, be sure you solder or get a very good crimp, and use shrink tubing on the end to help keep it supported. You can also double the wires over, too.

[@Gibbs58117]

How did you get the reverse light in the bed?

[@GeneralTalkWithBen]

Remove the side panels (tilt the bed, then remove the single screw at the front). You can then reach down into the void to connect everything.

[@micheal5936]

What size relay would you use for those lights?

[@tahoe9813]

It was just a standard 40 amp relay. Here's the set I had purchased from Amazon: www.amazon.com/gp/product/B017VDI0GY.

[@micheal5936]

Thanks. Great job.

[@6669bj]

Have a link to the reverse lights?