Best Bit Holder? Milwaukee vs DeWalt, Makita, Hilti, Irwin, Ryobi, Bosch, Neiko, Wera, Wiha

Bit Holder Brands Tested: Wiha, Wera, Milwaukee, Crescent Vortex, Norske, DeWalt, Neiko, Hilti, Irwin, Makita Gold, Bosch, Ryobi, Makita ImpactX, Yakamoz, Tomoto Palace, Horusdy. Bit holders compared for maximum torque before failure, magnetic bit retention holding strength, magnetic hold on fasteners, speed of driving in fasteners, and wear resistance. All bits tested until failure. I purchased all of the bit holders to ensure an unbiased review. So, thank you for supporting the channel.
➡ Thank you for supporting the channel through memberships:
/ @projectfarm
➡ Thank you very much for supporting the channel through Patreon: / projectfarm
➡ An easy way to find past videos along with products tested: bit.ly/2FCrBpk A big thanks to Jim for putting this together.
➡ Merch: project-farm.com
➡ Click here if you'd like to subscribe: / @projectfarm
➡ As an Amazon Associate I earn from qualifying purchases.
➡ Products Tested In This Video (in no particular order):
Wiha: amzn.to/3vu91rj
Wera: amzn.to/3y0X8KT
Milwaukee: amzn.to/3Kkn7j1
Crescent Vortex: amzn.to/3KkskYe
Norske: amzn.to/3vl1Z7Y
DeWalt (locking): amzn.to/3ki3NIw
DeWalt: amzn.to/3EQnwZn
Neiko: amzn.to/3KjqXsv
Hilti: amzn.to/36WHS6Q
Irwin: amzn.to/3EQlUPc
Makita GOLD: amzn.to/3vjVke6
Makita ImpactX: amzn.to/3xX1rqI
Bosch: amzn.to/3vkVIJC
Ryobi: amzn.to/3KfeuGx
Yakamoz: amzn.to/3MCKVAj
Tomato Palace: amzn.to/3MX4qWN
Horusdy: amzn.to/36Q61f4
The Pen I Use in Videos: amzn.to/3OVAlGv
Videography Equipment:
Sony DSC-RX10 III Cyber-shot Digital Still Camera: amzn.to/2YdXvPw
Canon 70D Camera: amzn.to/31b5Gy0
Azden Microphone: amzn.to/34d3DLE
Go Pro Bundle: amzn.to/3Ca0ZVN
This video is only for entertainment purposes. If you rely on the information portrayed in this video, you assume the responsibility for the results. Project Farm LLC

[@REDBIRD-95]

Crescent Vortex: "It claims to be unstoppable and unbreakable" Those words don't exist on Project Farm😊 Thanks Todd for another awesome vid👍

[@ProjectFarm]

Thanks and you are welcome!

[@hightttech]

"UNBREAKABLE"... what genius GYPSY college-marketing graduate thinks that's a believable claim?? 😆

[@ulyssesreyes6374]

@@ProjectFarm j J eore

[@echo4whiskey]

"we're gonna test that"

[@troybelding3816]

@@hightttech The same dimwits that keep selling 'shatterproof' plastic tubs at both Rubbermade and Sterilite, among others.

[@therealdojj]

"i'm going to break some, so i bought two" that's the sort of testing we have come to expect from project farm

[@ProjectFarm]

Thank you very much!

[@therealdojj]

@@ProjectFarm and shout out to cousin eddie too lol

[@om617yota8]

Reading this comment right when the Crescent "unstoppable and unbreakable" claim was read in the video. I chuckled!

[@jessehickman668]

This channel has become invaluable. Every time ima buy a tool or blade or whatever…. There’s an in depth video. So many channels that are thinly veiled ads. Thanks

[@ProjectFarm]

Thanks and you are welcome!

[@jeffjankiewicz5100]

It claims to be unstoppable and unbreakable... We're going to test that! Love the content. Yet ANOTHER great comparison and strength test by Project Farm. Love the logical testing, I base my purchases on these tests. Thanks again.👍

[@ProjectFarm]

Thanks and you are welcome!

[@TimeSurfer206]

I have started looking at this channel before I even log onto a website to start shopping. Mr. Farm (May I call you Project?), you are a Wallet Saver, not to mention frustration.

[@hugheffo]

Tomato palace. “$5 for 10 bits, or $2 each”. Is this the state of mathematics in America?

[@BYOTools]

THANK YOU for testing magnetic hold and pull out strength. Two very useful items to have in my book.

[@ProjectFarm]

You are welcome! Thanks for the feedback.

[@chowderwhillis9448]

@@ProjectFarm hey I use these bit holders everyday a lot, and the Norske got clogged up within 2 days (I bought 2) and it stopped working within a week for both, all I was using it for was screwing advantech down with saber drive screws. The DEWALT foreskin sheath and Milwaukee locking but work the best imo, just don’t beat up the sheath DEWALT it’s most helpful for screwing screws one handed while reaching out on pumpjacks

[@ToIsleOfView]

@@chowderwhillis9448 Norske clogged? Dirt? metal shavings? How did it stop working? lost all magnetism? stripped out? clogged?

[@Bootchair]

@@chowderwhillis9448 I like the term foreskin sheath so fitting 😂

[@Fister_of_Muppets]

The "unknown" test in my case is "where did I lose my bit at?" For the strength of the Horusdy, I'd say $10 for 10 bits it a pretty good deal for those who put them through thousands of cycles in rough environments. If one breaks or gets lost, not a big deal.

[@ProjectFarm]

Actually $2.00 each. Sorry for the mistake!

[@jonc8074]

@@ProjectFarm still a good price

[@hillbilly4christ638]

same with bits, so buy a tin of them.

[@michaelp1758]

@@ProjectFarm where can i buy them?

[@flarenator]

@@michaelp1758 There's Amazon links in the description

[@burkea29]

These have to be some of the best videos on KZbin. No bullshit, no bias, straight to the point, thorough testing. Just good, honest, useful and educational videos the likes of which KZbin was made for.

[@ProjectFarm]

Thanks so much!

[@TheBanjoShowOfficial]

I'd be tempted to say that the time to drill each screw in with everyone of the bit holders is so close at times that it is more often going to be decided by factors such as the applied pressure on the drill, the particular grain of the wood at any random section, and the angle at which any screw is being driven in. Having three trials eliminates some of this variability partially, but I think only so much. They are all so incredibly close. What really matters here is the wear and tear more than anything.

[@ProjectFarm]

Thanks for the feedback.

[@TheBanjoShowOfficial]

@@ProjectFarm love the videos regardless

[@MissPenguin]

I agree, and I also still have a hard time understanding "why", except for the difference in weight of the bit holder and potentially the impact absorbing "design features", the times would be different at all? Aren't they all spinning at the max speed the Impact driver produces?

[@drewdoestrucks]

I can't speak for the creator, but some bits tested claim to absorb shock to protect bits and fasteners. This would absorb impacts and slow driving. I think this was why it was tested.

[@LarryBloom]

@@MissPenguin I had the same question, but think it is because the nature of an impact driver is to repeatedly apply torque and then relax; if there is a lot of twist in the shaft or free movement on each stroke, that would use up some energy.

[@TopGoose-bf1mx]

Dude yes! Perfect way to start the day. Thank you for all the hard work you put into these videos. I’ve made several purchases based off these videos and they’ve all been great! My opinion of this channel: “Very impressive.” ✌️

[@ProjectFarm]

Thank you very much!! This means lot to me!!

[@lewiemcneely9143]

@@ProjectFarm I 2nd the Goose!

[@banoodel5121]

Where do you Live? Australia?😅

[@TGBdani]

here in Europe we finish the day!it's 10 pm here

[@yomyh]

@@TGBdani hey, it's a great way to prepare for a new week :D

[@25ellisd]

I've watched almost every video you've posted in the last 3 years and want to say thank you, for all the hard work that you've put into helping all of us make educated purchases. Keep up the awesome work.

[@ProjectFarm]

Thank you very much!

[@JohnDoe-ef3wo]

I have to agree with David. I've avoided entire products because of this channel..

[@TheRealSkeetman]

I really appreciate the content you put out. Not bland, informative, purpose of helping others find the best products they can. Only creator I’m a member of patreon for, I hope the videos keep coming for a good while longer 👍

[@ProjectFarm]

Thanks so much! Thanks for being a Patreon!

[@GrantButler]

I love being able to go back to videos like this when I'm shopping for something specific. Thanks!

[@ProjectFarm]

Thanks for sharing.

[@electronicsNmore]

You always do such an outstanding job making these testing videos. I not only like your testing methods, but the close up shots as well. Thank you!

[@ProjectFarm]

Thank you very much!! This means a lot coming from you. Your videos are outstanding!!

[@jeffalan6339]

Yes doesn't he. From simple things to tools. Even car care, I offer few suggestions to testing. This man is a visionary.

[@judih.8754]

Yes just the facts. And no fluff or wasted time.

[@CDXLIV444]

I was thinking the same thing. These are so well done.

[@Redlinedjr]

@@ProjectFarm 1:01 Tomato Palace 🍅 $5 dollars for 10 bits or $2 dollars each ? 🕵 you meant ¢50 cents each, or is my math wrong someone?🤷‍♂

[@CrippledEagle]

Excellent idea! I have a drawer full of these and can definitely tell the difference between the cheap ones and the more expensive ones. Another good one Todd!

[@ProjectFarm]

Thank you very much!

[@ThriftyToolShed]

Great video! Thanks for all your time involved in testing these!

[@ProjectFarm]

Thank you very much!

[@matthewmarek1467]

I love how Wiha and Wera have become staples of these kinds of tests. I hadn't even heard of them until they showed up on your channel. I'll definitely be looking towards one of them when it's time to upgrade. Also, those Makita bit removal jokes were gold!

[@ProjectFarm]

Thanks for sharing!

[@bm2618]

German quality engineering. Also I believe there pronounced vee-iha and vee-era as W in German is pronounced like a V in English.

[@dylanwheaton2785]

Lowes has the terminator 40 piece wiha bits for 30

[@mikeoag6579]

Would love to see a test on paint strippers, aircraft stripper VS one of the eco friendly safer to use brands. Would also be neat to see if brake fluid removes paint as much as people say it does

[@ProjectFarm]

Thank you for the video idea!

[@tintinlavigne5257]

Anti freeze coolant also is know in France for ruining the paint.

[@AAP0000]

Just use carb/choke cleaner or brake fluid. That stuff not only strips the paint, but it devours it. lol

[@tintinlavigne5257]

@@AAP0000 it's just a little expensive for a whole car🤣

[@Abrankod]

Sadly, "Aircraft stripper" no longer contains Methylene Chloride, which was the powerhouse for getting paint to really just jump off surfaces. One would have to try an industrial remover that still has the Methylene Chloride to really get true results of what aircraft stripper used to be like.

[@StefsEngineering]

I've got the Wera for a couple years now and am very happy with it! Came in the diamondcoated bits set and holds up great just like the bits themselves

[@ProjectFarm]

Great feedback on the Wera. Seems very well worth the price!

[@StefsEngineering]

@@ProjectFarm it sure is! easily one of my best purchases for the workshop, just like the knipex parallel pliers (those with the smooth jaws) and the inbus keys with that "hexplus" feature. When someone asks for tips for tool purchases those are always on the list, next to quality safetyglasses (I use Oakley M-Frame) and comfortable, quality earprotection (3M Peltor X5A in my case). Having comfortable and quality basics makes the whole experience a lot more enjoyable (especially when working with powertools that require PPE)

[@jackof1]

Just picked up a couple Wiha locking bit holders. Gotta check out the Wera

[@StefsEngineering]

@@jackof1 For sure something to look into in the future. The set I referred to was "WERA BIT-CHECK BC 30 DIAMOND 1" I just checked, I bought them 4th of april 2018 and of each type the first one is now worn to such a degree that I prefer to use another but are still usable. They are obviously not used every day but i'd say at least twice a week

[@calculator1841]

I got my Wera bit after watching Project Farm, holds up!

[@MongooseReflexes]

Yet again, you somehow come out with a video of something I was about to get! Thank you for all that you do!

[@ProjectFarm]

You are welcome! Perfect timing!

[@MSRWorkshop]

I have the Wera and love it !! It’s interesting that almost all the stuff that’s included Wera has finished always close to the top. It always been my favorite brand. It just works

[@pa6370]

It exactly what you should expect from tools made around Wuppertal. It's in their DNA and the water supply!

[@AustinMichael]

It better for the price.

[@TlD-dg6ug]

@@AustinMichael you mean less than half of snapoff?

[@joshmcej]

Happy to see Hilti products make it into the rotation. Helps to see if their premium price point is reflected in product quality based on comparative testing.

[@lunchboxproductions1183]

All the Hilti bits are just rebranded Wera

[@ProjectFarm]

Thanks!

[@harrywalker5836]

@@ProjectFarm heres a god damn suggestion.. i worked construction, in cairns, aus. with a bunch of vikings.sweeds,, they drink vodka like water, but,, they had these crawbars,[ wrecking bars], to you,, about 3' long alloy color.. they dont rust.. they dont bend, they dont get stolen,,or you die..&, they ring..would love one, but. not sold in aus..craw bar,, with the bent ends & 2 toe foot. pinch bar,?.. anyhoo. more value than gold..still waiting for the vid of the difference between blonds, red heads & natural. im sure the missus changes color hair for the moods..im so confused.. thanks tod, stay safe, . vote for humanity, not poli,s..

[@RagingOatmeal]

@@harrywalker5836 that was a very entertaining read. Hopefully your head doesnt hurt when you get up in the morning

[@TranceFur]

Not sure, but those Viking wrecking bars might be made by a company called “Svedbro Smide.” They call it the “Tove” wrecking bar. Pricy, but they look like some quality pieces.

[@wbhk1]

I don't think I've ever commented on your channel. I just wanted to applaud your well deserved success. I truly appreciate you going through the trouble of testing everything so thoroughly. I'm impressed with every video you post. Please keep it up!!

[@ProjectFarm]

Thank you very much, will do!

[@bluedeath996]

Good to know the Wera bit holder that came with my toolkit is actually as good as i would expect considering the whole kit was was only about 3 times the price of the holder you reviewed. Glad you are including Hilti now. Though it is hard to test it would be great to know how the best hold up over time.

[@ProjectFarm]

Thanks for sharing

[@Healcraft]

good to know my dewalt bit holder that came in a $11 bit set will burst into flames :)

[@Vengetuen_Wraith]

I never thought about how a bit holder could reduce driving speed, thank you for the torough testing you do, it really helps us all be more aware buyers, especially with tools as they are many people's livelyhoods!

[@ProjectFarm]

Thanks for the feedback.

[@Colorado_Native]

Can you test different types and brands of oil filter wrenches for gripping power, handle articulation for getting into awkward spaces, cost, etc? We love and trust your unbiased tests. Keep up the great work. Thanks.

[@ProjectFarm]

Thank you for the video idea!

[@glennllewellyn7369]

@TheCheesePlease Pull my finger.

[@joemilton7552]

@TheCheesePlease agreed, virtually never necssary

[@acrazedtanker1550]

And what about people with arthritis or something similar? Not very "useless" for them.

[@twistedhillbilly6157]

An oil filter wrench is just as important as many other tools. the girly-men below pay to have their oil changed so their powder-puff tool set doesn't include one.. I know what has worked for me and what has failed in the past but it's always interesting to see what cousin Eddy's cousin comes up with..

[@Aleks_Mechanics]

notification squad, Have a nice weekend!🔥🔥🔥

[@ProjectFarm]

Always great seeing your comment! Thanks!!

[@stonee1968]

Really appreciated the end where all the data was compiled, thanks!

[@ProjectFarm]

You are welcome!

[@vinnymunsey7342]

I love watching your videos. They have helped me make some pretty great purchases over the past several years. I would love to see you test out some gas powered weed trimmers and cordless ones as well. I’m looking in to buy some but the reviews are crazy to follow on some of them. I know you put in a great deal of testing and would love to see the outcome. Thank you for the videos and keep up the excellent work

[@ProjectFarm]

Thanks, will do! Thanks for the video idea.

[@thedevildick1]

The detail, effort, and pure passion you pour into your videos is simply astounding. Thank you very much, Todd. Your videos are the hi point of my weekend.

[@ProjectFarm]

Thanks so much!

[@STUDLEE1A]

Love all your videos. Seen every one! Just looked back yesterday at the wiper blade review before replacing mine. Thanks for what you do!

[@ProjectFarm]

Thank you very much!

[@bansheedearg]

Agreed, I don't use half the tools featured at PF but the wiper blade review was widely applicable to tons of people. More than the wax but the wax one was mesmerizing, just watching Todd use his creative jigs and methodical testing is always inspiring.

[@LurkerPatrol5]

I literally bought a bit holder last week and now you release this video!

[@ProjectFarm]

Thanks for sharing.

[@MADHIKER777]

Amazingly complete testing! You never cease to impress!!

[@ProjectFarm]

Thanks so much!

[@TranslateToEnglish]

Now that has got to be everything that I ever wanted to know but was afraid to ask about bit holders!

[@ProjectFarm]

Thank you very much!

[@adamford8708]

Thank you for all the great testing, you’ve saved lots of time and money! Have you considered doing a video on common chisels? They come in a very broad range of prices, and it would be nice to know if the expensive ones are actually worth the money.

[@ProjectFarm]

You are welcome! Thanks for the video idea.

[@Oddman1980]

That screw-on collar on the Neiko got my attention. I don't know how many times I've had a bit slip out when pulling the impact out of whatever I'm working on, because something got snagged on it. I love this channel because you test things I would never have thought to test - like screwdriver bit holders! I learned that I need to stop using the DeWalt bit holders next time mine breaks, because there are stronger options out there.

[@ProjectFarm]

Thanks! Thanks for sharing.

[@vicb8975]

As usual, a fantastic video, great tests for a LARGE number of test subjects. Got some DeWalts coming. Thanks

[@ProjectFarm]

Thanks and you are welcome! Nice!

[@kevinnorth2412]

I had no idea bit holders affected screw times so much, thank you for all you do man, what a great lesson learned! 👍

[@OFFICIALLYBENPEARCE]

well he had to had different amounts of pressure surely a test that eliminates human error would of been better for speed of screw

[@goofynoodle4775]

How?

[@purdyboi8078]

@@goofynoodle4775 What do you mean ' _How_ '... you ARE joking, right? 🙄

[@goofynoodle4775]

@@purdyboi8078 explain

[@no1slisteninganyway]

This is a bizarre coincidence. I had to use a bit holder yesterday while installing a garage door. After dropping the screw socket a few times and having to climb up and down the ladder to fetch it, I was wondering if there were better holders than the Black & Decker one I have. Thanks!

[@thegoods2240]

Me too, I lost my last one yesterday and am planning to buy a couple this week. I don't need the best for my lighter duty homeowner use, but now I can at least get a decent one for a decent price.

[@Tool_Addicted_Carpenter]

You can assume there's always something better than whatever black and decker product you're using. Black and decker is bottom barrel across the board these days.

[@Jako1987]

That is irritating way to lose bits

[@obelic71]

@@Tool_Addicted_Carpenter In Europe B&D has several ranges. the cheap B&D range, fair Stanley range, good Piranha drills/bits etc. etc. range, Dewalt/Stanley fatmax toprange.

[@thegoods2240]

@@Jako1987 Yeah, and even more irritating is that I will find all the ones I lost the day after I buy new ones!

[@0zmosis2001]

When you think about it that's pretty wild how much of a difference a bit holder makes when driving screws. So thank you for your particular this and thorough testing that you do to save us consumers time, energy and money when buying said items you test

[@ProjectFarm]

You are welcome!

[@sphelx]

Another outstanding set of test as always! Keep it up - You're doing such great work and make such fine examples of product testing content!

[@ProjectFarm]

Thanks, will do!

[@joeyjohnson9765]

I literally just broke my Dewalt one yesterday, crazy that you just post a video on this, love the vids man

[@ProjectFarm]

Perfect timing! Thank you

[@whiskeytango9364]

Great video as always...sometimes I see what is better than what I currently have but most of the times my tools and why I bought them are reinforced. Best channel on KZbin

[@ProjectFarm]

Thank you very much!

[@bigron26048]

Ya gotta love this guy's videos! He goes into complete testing of a product.

[@ProjectFarm]

Thanks!

[@MCHorner]

Great work again. Thanks for all your videos. Locking bits are great however, when using them to extend a drill bit the ones that release by pulling the collar toward the drill can accidentally release and leave your drill bit deep in your project. For bits that you want to extend working length I recommend the Bosch that has two locking set screws in the end of the shank. They tend to be the slimmest and also usually won’t release inside the work piece.

[@ProjectFarm]

Great point! Thank you

[@gunner6639]

Looking forward to this one! Thanks again in advance for your excellent content!

[@ProjectFarm]

Thanks again!

[@25TheCaveMan]

Always enjoy the Sunday video drops! Suggested product test ideas (if you haven't already tested them of course): ratcheting wrenches, jig saws or manual nut drivers...

[@ProjectFarm]

Great video ideas! Thank you

[@chuck5096]

Always just screwing around and still putting out awesome content. thanks again always curious to see what you come up with next.

[@ProjectFarm]

Thanks for watching!

[@andrewa4352]

I suggested this about 2 or 3 years ago after spending a-lot on a bit holder that really under performed. Glad you visited this. (My problem was holding onto the Philips head piece while maintaining a small profile)

[@ProjectFarm]

Thanks for suggesting this video test! Thanks for sharing.

[@621ELECTRONICS]

3:01 This style Dewalt was the first I got like this 20 years ago. Ill say it drove in a ton of drywall and deck screws over the years, using a cordless drill and setting the clutch as needed. It broke once I chucked it into an impact driver, and it broke fast. It definitely isn’t very strong compared to others, but I’ve had a few of them over the years and liked the size and sleeve on it, using with a cordless drill and clutch, they seemed to work fine for me. I learned not to use them for high torque or in an impact gun.

[@ProjectFarm]

Thank you for sharing!

[@TGC1775]

This channel really saves me money and time. Thank you.

[@ProjectFarm]

Awesome!! Thank you

[@Wellze-it9ji]

Great video! I have several of the Bosch bit holders and absolutely love them and I'm hard on my tools and never had any fail. Lot of good info though! May have to pick me up some of the Ryobi but holders

[@ProjectFarm]

Thanks! Thanks for sharing.

[@Zenkai76]

i get tired of my bits falling out, this helped me make a good decision, thanks!

[@ProjectFarm]

Thanks for sharing.

[@fmemories]

You do an incredible job, with a mechanical engineering degree I am always impressed with your processes and approach! Always a Sunday afternoon highlight for me. And I have purchased Milwaukee tools and other tools because of you. Keep it up. "Very impressive" indeed.

[@ProjectFarm]

Thanks so much! Your feedback means a lot to me!

[@fmemories]

@@ProjectFarm an idea. I have dug into MSDS of hoppes 9 and other oil and cleaning products and found they are, many times, 99% the same as common products such as mineral oil, atf, hyrdraulic fluid. Would you take the winning CLP and compare to basic off the shelf products?

[@simmcowaPang122]

I have done some of my own testing on locking 6"and 12" extensions, and I learned that the Irwin will use those 3 little "fingers" to grab onto a bit that has lost the ball detent portion. So essentially it grabs into a smooth 1/4" shank, which is perfect for using my Diablo Speedemons. I've broken at least 10 of them in my extensions and have to use a drill bit to pull the end out if the extension. But, after they break, using the Irwin allows me to keep using the bit with the same retention it had before! All other extensions allow the bit to fall out.

[@ProjectFarm]

Thank you for sharing!

[@TehBIGrat]

Thanks. I'll have a look at the Irwin ones here and see of they are the same. Some bit holders don't like the double ended bits.

[@CaptainGoldsmith]

Love your videos, Oz! Not sure if anybody's made the suggestion yet, but I'd like to see a comparison like this, but with drive guide bits.

[@fullonaudio]

Always impressed by the attention to detail. I'd be keen to see an SDS showdown

[@ProjectFarm]

Thanks! Thanks for the video idea.

[@charlesdalton985]

As always - thank you. I was confused by the results of the 5 dollar DeWalt, as I’ve beaten the heck out of mine for years with no issues. I went out to my workshop to look and they must have changed their design. Mine is a hex shaft, into a hex receiver. Again, thank you, because if I ever do wear this one out, I would have purchased another and been very disappointed.

[@ProjectFarm]

Thank you for sharing!

[@chrisengle2315]

Hey man I really really enjoy your content and I really enjoy the videos where you test different oils with the lubricity test, the cold flow test, and then you send them off to a lab and show us the ppm of the products.. but I notice you don't really have any videos doing that on different brands (super tech, oriley and autozone housebrands, valvoline etc.) and different types of transmission fluid (Mercon 4, Mercon 6, Type F, CVT Trans fluid, ect.) I would like to see this done with transmission fluid. And then at the end of it all you could do a competition like you had Amsoil vs Pennzoil in a showdown type of video. Love you content and Im a huge fan. Felt this was a good idea.

[@labrat7357]

Thanks for the video, I enjoyed watching it. A long time ago I bought a set of "no brand " bits in a cheap shop. The bit holder had an appearance similar to the Tomatoe Palace in your testing. On the first screw, a 35mm drywall type into a soft pine stud the bit burst out the side of the chrome plated part revealing it had been cast from pot metal and then plated. I can never understand why they would use an unsuitable material and then go to the expense of plating it. All the best and keep them coming.

[@ProjectFarm]

Thank you!

[@njmikeche5575]

I can confirm from experience that those Makita Gold bit holders work very well if the magnetic screw-holding is a priority. They are a little finicky to install bits, but I just bought five of them and keep them pre-loaded with some of the most commonly used drivers. The short Wiha driver bits make a nice combination here, as they are slow to wear out and have a very accurate fit to the fasteners. In my case it's not about pre-loading screws, but rather to avoid dropping screws when I remove them from furnace cabinets / service panels / etc. These things have saved me lots of aggravation, I used to drop screws all the time! A side note, It is unexpected to see the DeWalt long-sleeve bit holder fail so spectacularly. They must have changed something, I have a couple of those (at least, similar looking) bought many years ago and they are still perfectly useable.

[@ProjectFarm]

Thanks for sharing.

[@mattd.6679]

Definitely a fan of the chart at the end showing grades for all the tests and an accumulated, sometimes there's so much information (especially when testing lots of things) that it's hard to track without rewatching and rewinding a lot.

[@ProjectFarm]

Thanks for the feedback.

[@nigeld8694]

Agree, the table at the end was a great summary.

[@the_allamerican7057]

I’ll never get tired of this channel. It’s always my Go to when getting tools

[@ProjectFarm]

Thanks!

[@LS1LE]

Thank you!!! I hope you know how much you help everyone with your work!

[@ProjectFarm]

You are welcome!

[@dalinbaldwin6946]

Can we get a best impact nut driver? Also as a mechanic I'd love to see some videos about open end wrenches, rachets and sockets! Keep up the great work man

[@ProjectFarm]

Thank you for the video ideas!

[@dustinpomeroy8817]

I bought the Wera color coded about 2 weeks ago and man are they nice

[@jamiedaugherty1]

Great video! One are I would like to see improved is the torque test. It looks like you are applying a bending moment sometimes and others not. This is combined loading (torsion and bending) which can significantly affect the results. It would be nice if you could build a rig that holds everything coaxially. I this would generate more consistent results.

[@simontist]

One way to achieve this is with two u-joints: it's impossible to apply a side load then, provided the joints are approximately straight.

[@jimmyhill7707]

Awesome video! I love how in depth and unbiased your reviews are I would like to watch a test on wet tile saw blades

[@ProjectFarm]

Thanks! Thanks for the video idea.

[@tyrichardson7507]

Bro I love your vids so much. They are actually so calming

[@ProjectFarm]

Thanks! Glad to hear!

[@jewtube3311]

Oooh. I know it’s about bit holders but that impact driver is my favorite because it’s a monster.

[@ProjectFarm]

Great point! Thank you

[@majorahole]

That DeWalt bit holder says on the packaging "not impact rated". It's meant for a drill. They have a different model made for impact duty. I know because I had it break on me

[@lexel90]

and so was the Wera Rapidaptor shown here, as the fitting model would have been the Impaktorfor impact tools yet it still worked ;)

[@ProjectFarm]

Thanks for sharing.

[@davidmiller6010]

Thanks Todd, you always have such excellent and well thought out reviews. I have learned, (sometimes the hard way), to always check here first if I am in the market for a tool. You've pretty much got it covered. Until today. I find myself in the market for a battery operated hedge trimmer. And alas, there does not seem to be a Project Farm review. So how about it Todd? You up for a review on battery operated hedge trimmers? Of course by the time you could do a review, I will have already taken the plunge. I am leaning toward the newly released EGO platform, since I already have several tools in that lineup. And a super thank you for never accepting any sponsor ships! You rock!

[@ProjectFarm]

Thanks so much! Thanks for the suggestion.

[@quincymcguire287]

I love your unbiased testing and reviews. I just recently found you and I subscribed. I would like to see your testing of digital multimeters and drain cleaner products like Drano versus Liquid Plumber. Thanks!

[@ProjectFarm]

Thanks! Thanks for watching and subscribing! Thanks for the suggestion.

[@quincymcguire287]

@@ProjectFarm I found one you already had on drain cleaners. I'll be sure to check it out.

[@joeball1st]

I've only used a few of these, never had enough load to break one so far. I personally love the Makita Gold and their golden bits, love Hilti except that it is difficult to pull the bit out.

[@ProjectFarm]

Thanks for sharing.

[@DiniduPerera]

This is a great video! I actually bought a new bit holder because I hate my Makita one. (Such a pain to get bits in and out) At the store, I was faced with a wall of choices and no clue what to buy. They all claim to be great, but it's fantastic to see some actual numbers behind them.

[@ProjectFarm]

Thank you!

[@baalzevuv4509]

Thanks for review, just added Makita Gold to my cart, no more struggling with poor magnets in some applications!

[@ProjectFarm]

You are welcome! Thanks for sharing.

[@sonny.v925]

Been thinking since Sunday if there's anything you missed with this test. So far, I have nothing. lol. Nice job, Todd! 👏🏻

[@ProjectFarm]

Thanks!

[@sunglint]

I just bought the little Wera, and I love it. It's tiny, and the one handed bit swap works great. I was put off by how much it cost, but now I see it was not a bad choice at all.

[@ProjectFarm]

Thanks for sharing!

[@saladgreens912]

A lot of bit sets come with holders that are different than the ones sold separately. Would be nice to see them tested as well to be able to better compare the ones we already own to these. Though I see how that would increase the cost significantly. Very valuable work you do nonetheless.

[@ProjectFarm]

Thanks! Thanks for the suggestion.

[@jimivey6462]

The #1 holder in this video is the DeWalt model DWA3HLDFT. It is my all-time favorite. With it, I can put in hundreds of deck screws at a time without the bit falling out.

[@mohsinrasul8450]

Todd... Thanks for testing wera... Ive had mine for 15 years now... Still going strong.

[@ProjectFarm]

Nice! You are welcome!

[@davidvilabrera]

Scientific, precise, honest appraisals - I enjoy watching your reviews. Keep up the good work.

[@ProjectFarm]

Thanks!

[@_GntlStone_]

Your videos and testing methodology is invaluable! Thank you for the time and effort each video takes. Would you consider adding chapter markers in the future? For ease of access in going back to a certain section it would be very helpful. (Gamers Nexus, especially their weekly update videos, has an excellent implementation for reference)

[@ProjectFarm]

Thanks and you are welcome! Thanks for the suggestion.

[@jakesaari7652]

Wow! I suggested this a while back, and there's a lot more to these bit holders than I would have thought. Having the right one for the job makes a big difference. Good to know even the cheap ones can take a lot of abuse. It would be interesting to see what the lag screw speed would be for a dedicated 7/16" bit driver without the extension.

[@ProjectFarm]

Thank you for the video idea!

[@caodesignworks2407]

@@ProjectFarm Indeed, I just finished a project using concrete screws and stripped out several 5/16 drivers from various brands.

[@jamesadams2333]

I oughta get one of these! I did see a few sparks fly with the torque breaking test. How fascinating and well done.

[@ProjectFarm]

Thanks!

[@BY-ib9ew]

I'm extremely thankful that there is a Project Farm video for pretty much every tool I plan to buy

[@ProjectFarm]

Thanks for sharing.

[@rayrayber_]

That dewalt bit holder was like testing me in a milwaukee na I'm die out

[@ProjectFarm]

Thanks for the feedback

[@galacticgoose6255]

You do a wonderful job comparing the various products, as a carpenter I'm happy to have found your channel, thank you! I have a couple video suggestions; the first being to compare claw hammers (durability and ergonomics) and the second, 3x360 laser levels. Thanks again and keep up the great work!

[@ProjectFarm]

Thanks, will do! Thanks for the video ideas.

[@samrobinson9802]

As always, great job Todd.

[@ProjectFarm]

Thanks!

[@destrygriffith3972]

I'm really glad he's addressing how well they actually hold on to the bits and screws. I mean, other than breaking, that's pretty much all that matters.

[@ProjectFarm]

Thanks for the feedback.

[@Jannis368]

Here in Germany the Wera seems to be the standard recommendation. Together with a bit set the price is reasonable and changing bits is just so satisfying.

[@ProjectFarm]

Thanks for the feedback.

[@jake9705]

Been waiting for this one! Thanks for another great video. 🥳🥳🥳 Video Ideas 🥳🥳🥳 • Best portable solar panel for charging phone • Best reflective vest • Best traffic cone • Best unpowered pallet jack • Best fish tape for pulling wires • Best GIANT floor fan for cooling your whole garage or shop • Best tool belt • Best sonic cleaner for parts (gimmick?)

[@ProjectFarm]

Thank you for the video ideas and thanks for the positive comment!

[@daffydlwellen1270]

Another GREAT review. I bought a Bosch for all the driver tools I own.

[@ProjectFarm]

That is awesome! Thanks!

[@bjn714]

I used to install security equipment professionally and the Wera was the best bit holder I found for the job. Easy to change bits one handed, the collar slides toward the end of the shaft to remove the bit so the lock doesn't get accidentally released when inserting the drill into my tool belt, and never lets go when a bit is installed and locked. 5+ years of usage and it still works like new. I was previously using the Makita holders and I wanted to kill those retention rings, since the need for pliers to remove bits was a nightmare. Tried multiple versions from DeWalt, Milwaukee, and others, and none compare to the Wera in actual daily usage. $18 is a bargain (I think it was closer to $15 when I got it) compared to buying a dozen different ones that all perform terribly. I wish I had found your channel back then (even though this video didn't exist then), since I could have saved a lot of money on trying products that just didn't meet my needs.

[@ProjectFarm]

Thanks for sharing.

[@UtahDarkHorse]

The biggest issue I have with bit holders is the bit becoming stuck in the holder. I think you would have had to install more screws to run into that, but would've been nice to know which ones were suspectable to that and which ones weren't. thanks for sharing another great video ☺️

[@ssnerd583]

Yeah...a cheap insert bit will stick in some of these until you beat on them with a hammer or use a vise and vice grips to pull them apart.....BTDT

[@ProjectFarm]

You are welcome! Thanks for shairng.

[@unitrader403]

my personal solution to this is only using long bits, and dont fiddle with bitholders. Also very practical when you encounter recessed Screws, where bitholders are usually to thick to reach the screw.

[@UtahDarkHorse]

@@unitrader403 That's a really good idea. I have a few but could use some more. Thanks

[@purdyboi8078]

@@ssnerd583 Or maybe even using a vice w/vise grips

[@PetrosArgy]

This was an interesting review since it included both locking and unlocking types, plus what I would consider extensions rather than bit holders (ex. Irwin). I'm guessing every trade uses these items differently so the designs seem to target one or another use and optimize the mechanism (magnet, locking, retaining ring etc) for the use they think their users will benefit from. Of the styles you tested, I mostly use the magnetic style for insert bits (similar to the Hilti) for driving screws. The story changes when it comes to extensions, where my go-to is the Irwin series. In that use, I need to get more length for drilling with either spade or auger bits that use 1/4 hex shanks and the design of the Irwin has far outperformed any other extension brand I've tried. My record was 12 feet (12x12-in extensions) to drill down through the bottom plate of a wall from the attic with up to three extensions being the more common configuration when drilling across ceilings through recessed light openings or horizontally through multiple studs during a rough-in. Most other locking bit holders/extensions come apart under these conditions, whereas the Irwin design doesn't typically fail until the flexing of the stacked bit holders breaks the shank of a bit holder (where the notch is for the locking ball). Granted, this is an extreme use scenario, so until the standard is changed for the length of shank gripped above the locking notch changes or someone makes an entire series of 5/16-in extensions, there probably won't be an improvement to performance.

[@ProjectFarm]

Thank you for sharing!

[@michaelstella5771]

Thanks for all these videos. I work construction and hate wasting money on cheap tools that break at first stressful use. Whenever I think about buying a tool, first thing I do is come here to see if you stress tested it. You’ve saved me a few times from buying the wrong thing. So again great videos, testing process is awesome, and love the humor “we’re gonna test that!” Would like to see a vacuum cleaner comparison. Dyson, Hoover, Eureka etc. (not shop vac).

[@ProjectFarm]

Thanks and you are welcome! Thanks for the video idea.

[@DanielRyanScott]

Really appreciate all the different points of view you offer. Its not so much "What is the best tool", but instead "What's the best tool for which kind of work". I do a ton of over head house work, so having a magnet with a sleeve is a necessity. My brother who works on cars hates them, the metal in the engine bay attracts the magnet and the sleeves take up too much room in those tight quarters. Anyhow, thanks for your videos! And the links, sometimes its hard finding specific model numbers... especially if the products are designed to look alike but have different internals.

[@ProjectFarm]

Thanks!

[@antonhan4815]

I found out the hard way about the Makita Impact X. I was able to pinch the retaining rings so they widened a bit and much easier to install and remove. But I'm now interested in mostly the bosch and wera for the convenience features.

[@ProjectFarm]

Thanks for sharing.

[@AG-en5y]

you think Bosch would be better than the Irwin ? Seems like Irwin more convenient

[@catfishbilly7425]

Great video as always! I'd really like to see a comparison of 3 jaw pullers, lost count of how many I've broken over the years (probably more my fault for overstressing them, of coarse). Would be nice to know what brand would survive my abuse lol

[@ProjectFarm]

Thanks! Thanks for the video idea.

[@Aceedmonkey]

Awsome work as always!!! 👍🏻

[@ProjectFarm]

Thank you so much

[@JMJost]

I liked this comparison review quite a "bit"..... Thanks Todd!

[@ProjectFarm]

Thanks and you are welcome!

[@ericcox6764]

Thank you for sharing this info. I was driving some screws the other day, using an impact driver with a 6" extender. As I worked, I was wondering how much torque I was losing, if any, by using the extension. I'd love to see you do a test using different lengths and brands of extension tip holders. Thanks and keep up the great work!

[@ProjectFarm]

Thanks, will do!

[@ObservationofLimits]

Torque test channel has a few of those. Essentially the longer the shaft and the more connections the more torque you're losing. As for impacts, slop between connections also starts playing a part.

[@ericcox6764]

@@ObservationofLimits thanks for the heads up on the videos. I'll definitely check them out.