Betaflight won't arm - all 26 reasons explained

[@FPVUniversity]

12 NEW things you should know about Betaflight kzbin.info/www/bejne/nmqUooWNerN1nqM

[@bad2thebone244]

So what if upu have no arm disable warranty but it still will not arm? Endpoints setup, not gps rescue as you need gps lock before taking off, switch arming is on and working,throttle down don't work. Tx in binded with rx and is showing in bf, done is level and collaborated. Just refuses to spin motors with tx but in bf with sliders they spin

[@MrBcast99]

for the throttle issue.. you didn't explain how to get it between 1000 and 2000, could you please elaborate on that? thanks

[@B3NSipodtouch]

Great video! There one more I can think of . Crash flip !! If the arm switch is the same as the flip over crash the quad won’t arm

[@PkwyDrive13]

Most probably a great video!

[@BBFPV]

And now, the fist 126 reasons why inav won't arm. nav_extra_extra_safety_arming = ON allowed values ON, very ON, EXTREME ON.

[@MCsCreations]

Fantastic, Pawel! Thanks a lot for the video! 😃 Stay safe there with your family! 🖖😊

[@tiwidub8809]

Excellent explaination. Many thanks.

[@FPVUniversity]

Glad it was helpful!

[@micsherwood4930]

I have Many qwads now that i have bound (BetaFPV TX module and HM EP2 RX's) and BF gives RXloss in cli tab, and still do not arm. what else could be holding ALL my qwads from arming? I only have one qwad, using ELRS that is bound, able to get into BF and running great. My other 8 get nowhere.

[@FPVUniversity]

BF gives you precise reason why it not armed. Just see which flag is set

[@PHOTOZULU1]

Amazing work ..thank you !!!!

[@FPVUniversity]

I'm very happy you liked it!

[@babyzfpv1234]

The one thing you forgot, was if a pilot does an incorrect CLI dump, and is actually able to save and execute the dump, then the quad will load up, show that you have telemetry, and even lose telemetry when you unplug the quad. But not arm. And you notice in the modes tab, that when you go to arm, the little ChickLit moves into the slider range, but arm is not highlighted. Nor are some or all of the different things like air mode, horizon, crash flip, etc.. So the solution obviously is to find the correct CLI dump. It happened to me, I found this video, and then later was lucky enough to grab the correct CLI dump for a GEPRC phantom analog. Hit me up if you need it.

[@midge9740]

my arm tab doesn’t highlight, but the other modes like air etc do. thoughts?

[@babyzfpv1234]

@@midge9740 my first thought says check your channel mapping. And also go back to the receiver tab and make sure that the arm switch (and all others in correct order) is actually popping up when you engage it. If it isn’t/they aren’t popping up in the right order…then check your channel mapping on the radio versus Betaflight. Off memory, that’s my best idea.

[@MichaelRogersJesusrules]

Awesome it will help a lot being new. much love from Sth Aussie outback, God bless n thank you for the video!

[@FPVUniversity]

Glad it was helpful!

[@maddercat]

Lol first line, look at the effing info box, it was my newly installed gps, thanks! bardwell didnt say that on his vid.

[@FPVUniversity]

Glad to help

[@thejeffhendrix]

Can you do a video for inav?

[@FPVUniversity]

I did like 3 years ago

[@volkergoe]

Excellent roundup! I will send a lot of noobs to you from reddit ;-)

[@FPVUniversity]

Thank you very much 😁

[@johnkurpiewski3996]

I love you , and here I did not even know it tells you ! I’m an such a noob …

[@anthonylareppe5348]

Thanks sooooo much !!!

[@FPVUniversity]

You're welcome!

[@Droneterbang]

Help me. ARM disabled 😭

[@jeffdughman9741]

be patiencnt, youll get it, we all go through this stage in our quad lifes :) you will get it bubba !

[@MS-nj9le]

R.I.P FPV

[@tintenbomber]

Schwis

[@silvioparlato2719]

$M>âtARM;FAILSAFE;BEEPER;OSD DISABLE SW;BLACKBOX;AIR MODE;FPV ANGLE MIX;BLACKBOX ERASE (>30s);CAMERA CONTROL 1;CAMERA CONTROL 2;CAMERA CONTROL 3;FLIP OVER AFTER CRASH;PREARM;VTX PIT MODE;PARALYZE;DISABLE VTX CONTROL;LAUNCH CONTROL;¬$M>–

¼$M> ng Entering CLI Mode, type 'exit' to return, or 'help' help me plase

[@NewoneFPV]

Thank you solved my problem with GPS rescue 🛟

[@FPVUniversity]

My pleasure