BFT Phobos A40-A25 & Thalia Lite SD Quick Overview

[@bollol5141]

Thank you from Poland :)

[@chanwka]

Is it possible to install a manual wired switch?

[@BFTAmericasInc]

Yes you want the switch to be Normally Open and you would wire into 60 and 61 on the control board.

[@SamuelThesinger-vz5lq]

Hi, watched you video and I have an issue with my A40. Trying to do the programming but I get error 18 and when it does the auto prog it opens and then stops at the limit switch and then doesn’t go back and shows me error 18. Wondering if you know how to fix this issue?

[@geomot7443]

now i installed A25 same error. What was your solution to err18?

[@tractorguy97]

How do I turn off Auto-Close on my Thalia?

[@drbones6040]

Hi are these bft kustos reliable? Can we make it smart so it works with Google home?

[@LindaMartinez-l1l]

Kessler Oval

[@ontheway5967]

Good job

[@BFTAmericasInc]

Thank you!!! 🤝🏻

[@ChristopherMoore-k8p]

Reichel Mission

[@SommerMceachin-j6o]

Sydni Knoll

[@jarkstt]

Can you share how the separate battery backup kit is connected to the Thalia L board?

[@BFTAmericasInc]

Sure thing! Just write us at [e-mail] and we will share some quick guides with you.

[@patkie7089]

2:10 there can be another problem which I had :) I did not conect safety switch to socket number 42 (1 motor).

[@BFTAmericasInc]

It happens my friend. Glad you figured it out. I've also seen it happen with old cable being broken or shorted causing everything to go nuts.

[@matthewisaacs5307]

​@BFTAmericasInc We had a heavy rain and after both swing gates would open but only one would close ...... what should I be checking?

[@matthewisaacs5307]

​@@BFTAmericasIncNice video

[@minceaclaudiu3614]

Hi, How can i reset to factory setting model Zara for BFT Phobos A40?

[@BFTAmericasInc]

Thank you for reaching out. The Zara is one of our more basic boards and there really isn't a factory reset for it. To get it back to how it came, you would just simply put all the potentiometers to zero and only have dip switch 1 and 8 on. Press and hold s3 and it will be back to how it came from factory, but that will more then likely not fix any issues your are having. Now, if you want to delete all the programmed remotes you would simply push and hold S1 and S2 for 10 seconds and all previously programmed remotes will be erased from memory. Please reach out to us at [e-mail] and we will see if we can help you out a little further.

[@russellpugh617]

Thanks for the clip and I have indeed been forced to upgrade my Motors to A40. I have however the old LIBRA controller and now need to slow down one of the Motors on one of the two swing gates as they close together and in order to avoid a collision, I have to stop the gate closing and then start it again in order to let the 1st swing gate close before the 2nd wing gate. Do you have a video on how to program the LIBRA controller? ... thanks very much!

[@BFTAmericasInc]

we have no video for that but you can go into libra programming menu and but a longer delay time so the gate can close first

[@russellpugh617]

@@BFTAmericasInc thanks for the reply.. indeed now found the setting in question, was able to apply a close delay on the 2nd motor/gate. Thanks very much!

[@Horizon301.]

How old were the motors?

[@unseenaworld]

Can I get spare parts of arm motor? It always problems

[@BFTAmericasInc]

Sure. Where are you located so I can get you to the right BFT Branch?

[@sanjaques]

Excellent, it worked perfectly with both arms, but I failed with the photo beam cells

[@BFTAmericasInc]

Sorry to hear that. What exactly happen with the photobeams. Reach out to us at [e-mail] and we will do our best to help you out.