Locating the Secure Gateway Module on 2018 Jeep Cherokee and using the Autel scantool to clear codes

In this video #billymoa shows you the location of the secure gateway module on a 2018 Jeep Cherokee, and how to clear codes. Codes can not be cleared without bypassing this module.
The Autel scan tool can be found here. amzn.to/2UOrRaH
The Chrysler 12+8 cable can be found here. amzn.to/2OHyzvb

[@kentearly805]

I wasted time watching over half of this video before finding out that you are working on a GRAND Cherokee and NOT a Cherokee like the title says!!! Thanks!

[@lard1892]

Yea another loser on Jeep security.....explains the 400 subs

[@stephanreckard8991]

Hey cousin Billy I subbed to ur channel this is Stephan. Keep up the good work man. I gave you some watch time i watched a few videos.

[@jasonrivord3476]

Do not have to tear all that apart only have to pull left trim panel on bottom side of glove box corner closest to center counsel and can see the box and plug in

[@brucebragg2395]

It’s under the glove box

[@NoahKuzel]

That smaller battery is for the Auto start/stop system.

[@matts3694]

Thank you! this was super helpful and accurate for the 2020 jeep grand Cherokee

[@emersonaroche1965]

Gracias Mr.

[@1INSOLENTDOBERMAN]

When you first started on the right side just below the glove compartment. On that carpet type covering you had to remove just under the glove compartment, was there a little white arrow pointing up??? I ask because I will be using an XHorse Key Tool Max Plus to obtain my PIN number to program new key fobs , for a 2018 Ram 1500 Big Horn. I ordered the 12+8 bypass cables. I have read numerous articles & seen numerous videos as well showing the FCA black box in numerous locations on the 2018 Ram 1500 . Some show the left side by the steering column, some show behind the radio, some show on the right and some show behind the dashboard. I really don’t want to tear apart my truck looking for it. I just want to know if that little white arrow gives the location or if you seen it.

[@BillyMOA]

I believe the ram has it behind the radio. But they do change it between the various models. I haven’t tried a tool to get the pin number yet. I think that’s pretty awesome. Let me know how it works.

[@BillyMOA]

Also, I don’t recall seeing any indicator arrow. Sorry it was a couple years ago.

[@1INSOLENTDOBERMAN]

I ask about the little white arrow pointing up 👆, because on that carpet like cover just under the glove compartment, on the left edge of the cover there’s a small white arrow pointing up.

[@abrvalg3440]

Thanks

[@transmisionesautomaticas5078]

Excelente video informativo.. es una lastima que en México no tengamos acceso a ciertas herramientas como el bypass

[@alessandrapetrone8395]

ciao dove si trova di preciso il modulo di una jeep compass 2018 ?

[@dashtyATG]

Hy again thanks to you hard work. I've found it but i didn't removed any plastic clips just entered from the back of it. But 1 thing please is it the same laredo and cherokee?

[@BillyMOA]

I'm pretty sure they are the same.

[@dashtyATG]

@@BillyMOA yes i did checked on Google result showed the same. Thank you.

[@barbi82276]

I have a 2018 Jeep Cherokee Latitude, not a JGC, where is the bypass on that? I've looked behind the radio, and it's not there... any help would be greatly appreciated!

[@BillyMOA]

It might be under the glove box on the left side of it. Next to the carpet on the hump. Hope this helps.

[@victornaja-paz5241]

hi any idea where i can find the security gate way module on a 2019 dodge grand caravan please help.

[@BillyMOA]

I will see what I can do tomorrow when I am at work.

[@Junior.illinois]

Hello any ideas of jeep cherokee latitude 2019 12+8 bypass location?

[@lollol2283]

Can I use that adapter with launch x431?

[@BillyMOA]

I think the adapter will work with most OBD 2 scan tools.

[@lollol2283]

@@BillyMOA thanks

[@bombaicantor6018]

with the cable only you can check codes? you can do relearns on trans and engine??

[@BillyMOA]

If you have the cable you can do relearns on the trans and the engine and various other modules.

[@truth4reel]

Service info would show the location

[@bugy207]

DUH, it's a right hand side (passenger side)

[@rafatqaryouti2107]

Hello, i just came through your vehicle looking for solution for my 2018 Jeep Grand Cherokee laredo it has a code B2761-13 ( left B-piller impact acceleration sensor circuit open) I deleted many time but won’t go away… so can u tell me what is that code please and where can i find that sensor on my vehicle so i can change it, i don’t know where is the location of it. Please and thank you

[@BillyMOA]

Sounds like driver side rear pillar air bag might have a bad connection. or a faulty air bag. Typically an air bag has a resistance of 2.5-3.5 ohms. (including wire harness resistance.) What does live data day on your scan tool?

[@dashtyATG]

Hi there thanks for your support and sharing your knowledge. I've IM508 other day i tried to add an extra smart key to chrysler S300 i couldn't this cable was required exactly. If i get that cable would i be need in any others?

[@BillyMOA]

What year is the car?

[@dashtyATG]

@@BillyMOA it was a 2018 but sold 2 morrow I'm about to add a key to dodge challenger 2019 I've brought the 12+8 cable and now i wanna find the bypass location

[@NoNegotiations]

80% of Chrysler vehicles have SGM in 2018, 90% in 2019, and 100% in 2020. Prior to 2018, there is no GSM.

[@dashtyATG]

@@NoNegotiations ohh i see thanks for your time, how about under 18?

[@NoNegotiations]

@@dashtyATG As far as I know, they didn't have it under 18.

[@dashtyATG]

Hy brother sorry to weste you time. I've a quick question do you know the bypass cable location for dodge charger 2014 please?

[@BillyMOA]

I don’t believe the 2014 has a secure gateway module.

[@dashtyATG]

@@BillyMOA great answer thank you very much so please do you think i can add 1 extra used key to it via my im508. As i did to a dodge challenger 2019 with my Autel and the bypass cable 12+8 cable.

[@BillyMOA]

@@dashtyATG I’m pretty sure you can. You will need the vehicles PIN number for the security.

[@dashtyATG]

@@BillyMOA yes you think so? And I'm sure I'll be needing the pin and i don't know if my im508 will pul it out or not ill go for it on Saturday bruv.

[@BillyMOA]

@@dashtyATG good luck. Let me know if I can help.

[@Animallover233]

This a grand cherokee please title the videos correctly

[@dashtyATG]

Any idea on about jeep cherokee latitude 2019 12+8 bypass location?

[@BillyMOA]

Not off the top of my head. I will look it up when I get to work.

[@dashtyATG]

@@BillyMOA k thanking you

[@BillyMOA]

@@dashtyATG I think it is in the same spot.

[@dashtyATG]

@@BillyMOA I'm not really sure i didn't do it. How about compass 18 location any idea?

[@BillyMOA]

@@dashtyATG I will look it up but I think only like 25% of those vehicles will have the secure gateway. If it has one your scan tool will let you know.

[@chano113street]

Does the 8+12 connector power the scanner

[@BillyMOA]

Don Lopez It turns the scanner into the secure gateway module.

[@alessandrapetrone8395]

sgw

[@chano113street]

What is the reason for the battery disconnect? Doesn’t that cause a bunch of code in itself

[@BillyMOA]

Don Lopez No not really. Always disconnect the battery when changing a module or disconnecting modules.

[@lard1892]

Another terrible Jeep video