Blower Bearing Replacement

[@HVACRSurvival]

Thanks for the shout out 👍👍. I'm no one special but thank you for mentioning me. Keep up the great video work! The content was excellent, your editing, audio and picture quality we're top notch. Job well done

[@HughesManHVAC]

Thanks man!

[@TRDBoomer]

You are awesome sir , I wish a lot technician like you around here 👍👍👍

[@HamHavoc]

Thanks for the video. I have a job like this coming up so I appreciate you uploading the process. I was planning on cuttings the shaft and I'm glad it seems like its the correct way to go about it.

[@engeclimarefrigeracao3644]

That was a job! Congratulations, for your execution of the services, you in the USA, you have many tools and resources to develop a good job. I learn a lot by watching your videos. Congratulations

[@HughesManHVAC]

Thank you! I appreciate it.

[@williampagan4489]

Hello again Ryan, Keep on recording as long as you can and when you can, people will watch and comment...... I know I will. As always be safe and take care.

[@HughesManHVAC]

Thanks man!

[@hozerhvac4406]

Great demonstration. Summer repairs must be nice on the roof. Nice Alone and peaceful. I enjoy your videos as always....keep it up pal

[@HughesManHVAC]

Thank you Hozer!

[@oscarcarrasquillo9360]

I like the bucket Idea.😂

[@daviddesilva4971]

Gotta like those low voltage motors. Ha ha. Keep them coming.

[@HughesManHVAC]

Thank alot for watching!

[@winstonwright3613]

Came to your channel recommended by HVACR Survival. I think your videos are high quality with good content. You troubleshoot like I do, and its a pleasure to watch. Can't believe you don't have more Subscribers. Only suggestion.... maybe make them longer? Take us through the work (like you did in this one) more often like Survival and Chris @ HVACR Videos does. The way YOU work .... we'd all enjoy seeing it!

[@HughesManHVAC]

Awesome! I'm happy you enjoy the videos. Some videos work out better then others in the editing process. I will take your suggestion and apply it when I can, and I appreciate it. Rick at HVAC/R Survival is an awesome guy and a genius service tech. Nice to meet you Winston.

[@AlexGarcia-vv4ux]

💪Great video and humble attitude 💯

[@HughesManHVAC]

Thank for watching!

[@zekenzy6486]

Good Job. Thank my man 💯

[@johnstewart2767]

awesome video, thank you.

[@HughesManHVAC]

Glad you liked it!

[@AlexGarcia-vv4ux]

Good advice for the set screw with the 5/16 wrench . On some You can get a ratcheting 3/8 12 point on there .

[@HughesManHVAC]

Thank you for watching!

[@jorgealtamirano6611]

Good job sir thank u God bless! Keep up the good work!! U do your thing dont mind the bad comments its lots of help!🙏🏼

[@HughesManHVAC]

I appreciate that man. Thanks for watching!

[@dmitripogosian5084]

Need to replace bearing on my house furnace blower, but I need to keep a cage and pulley !

[@HughesManHVAC]

Hope it works out

[@dmitripogosian5084]

@@HughesManHVAC It did ! Just replaced it yesterday, furnace purrs like a kitten, better than in years. On a second thought should have probably used the old rubber gasket, the new bearings came with a little different (and more narrow) ones, but it looked damaged on the first glance, just later after I washed it, I saw it is all right. But now I can take it apart again if needed :). Bearing sleeve on a pulley side was eaten through like by 1/4 inch in a side, the blower was full of metal shavings

[@craigforster9861]

have tools to pop bearing out of bracket and off shaft will share

[@donnierobertson3088]

Nice job and video

[@HughesManHVAC]

Thanks Donnie

[@come_on_now]

To align pullys, i use a string from the far end of the blower pully and stretch it back over the far end of the driver pully. Once the string lays flat over the pullys, theyre aligned. Ive also used the straight edge of a tape measure. Lol.

[@pointbreak8293]

Awesome video sir...👍👍👍

[@patcotsman866]

Ok But why the background music?

[@HughesManHVAC]

Your right the background music is completely unnecessary! I haven’t watched this video in 2 years. 😅 my old videos weren’t the best.

[@ThermalDynamicSevices]

Going threw all that I would have gone with a whole new assembly lol

[@HughesManHVAC]

yeah if RSC wasn't always on back order for the housing parts I would prefer that. honestly it only took me a couple hours to make the repair anyway. thanks for watching!

[@josedelapaz3152]

Dude you make it look too easy....

[@HughesManHVAC]

Thanks for watching!

[@gene-khvacr]

👍🏻👍🏻😎🍻

[@HughesManHVAC]

Cheers!

[@steveblake8766]

#53 Thumbs uP!